Harman-Kardon AVR 430 owner manual Surround Setup

Page 24

System Configuration

* * S P E A K E R S E T U P

* *

 

 

 

 

M O D E

: S I Z E

X - O V E R

L E F T / R I G H T :

1 0 0 H Z

 

 

 

C E N T E R

:

1 0 0 H Z

 

 

 

S U R R O U N D

:

1 0 0 H Z

 

 

 

S U R R B A C K :

1 0 0 H Z

 

 

 

L F E

: L E F T / R I G H T

B A S S M G R

:

G L O B A L

 

 

B A C K T O M A S T E R M E N U

Figure 5

To change the setting for any of the four speaker groups Left/Right, Center, Surrounds or Surrond Back, press the ⁄/¤ Buttons Euntil the cur- sor is next to the line where you wish to make a change and then press the ‹/› Buttons E until the desired setting appears. The available choices at which point low-frequency information will be sent to the subwoofer (or to the Front Left/Right speakers in case subwoofer is set to OFF), rather than to the speaker channel, are 40Hz, 60Hz, 80Hz, 100Hz, 120Hz and 200Hz. Pick the choice that is identical to the information for the speakers, or if an exact match is not possi- ble, pick the closest choice that is ABOVE the speaker’s lowfrequency limit to avoid the creation of a low-frequency “hole” where your system will have no bass information.

In cases where LARGE has been selected as the front channel speaker option and LFE+L/R has been selected as the subwoofer option, the front channel sound information below the cross- over point selected for the L/R front speakers (when fronts are set to "Small") will be sent to BOTH the front channel speakers and the sub- woofer.

When all speakers are set to LARGE the crossover point for the fronts (selectable when they are set to "Small") will affect the LFE signal and the bass support for the front speakers by the sub (when the sub is set to L/R+LFE, see above) only. In that case the default value "100Hz" should be kept or selected for the crossover point for the L/R fronts (selectable when they are "Small") as it´s indicated (and marked by *) behind the LEFT/RIGHT line in the speaker setup menu when the X-OVER option is selected.

10.When all speaker selections have been made, press the ¤ Button Euntil the cursor is next to the BACK TO MASTER MENU line and press the Set Button Fto return to the Main menu.

11.The Speaker Configuration may also be changed at any time without using the full-OSD on-screen menu system by pressing the Speaker

Selector 6 on the front panel or on the remote control. Once the button is pressed, FRONT SPEAKER will appear in both the lower third of the video display and the Main Information Display ˜.

24SYSTEM CONFIGURATION

Within five seconds, either press the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons

Eon the remote to select a different speaker position, or press the Set Button @F to begin the adjustment process for the front left and right speakers.

When the Set button @ Fhas been pressed and the system is ready for a change to the front speaker setting, the on-screen display and Main Information Display ˜ will read FRONT LARGE or FRONT SMALL depending on the current setting. Press the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons Eon the remote until the desired setting is shown, using the instructions for “large” or “small” shown earlier, then press the Set button @F.

If another speaker position needs to be changed, press the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons Eon the remote to select a different speaker position, press the Set button

@Fand then the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons Eon the remote until the correct speaker setting is shown and press the Set button @ Fagain to con- firm the selection.

To assist in making these settings, the icons in the Speaker/Channel Input Indicators Ú will change as the speaker type is selected at each position. When only the inner icon box is lit, the speaker is set for “small.” When the inner box and the two outer boxes with circles inside them are lit, the speaker is set for “large." When no indica- tor appears at a speaker location, that position is set for “none” or “no” speaker.

Note: These icons are available only when making setup changes without the use of the full OSD mode.

As an example, in the Figure below, all speakers are set for “large,” and a subwoofer is set.

Surround Setup

Once the speaker setup has been completed, the next step for that input is to set the surround mode you wish to use with that input. Since sur- round modes are a matter of personal taste, feel free to select any mode you wish – you may change it later. The Surround Mode chart on page 29 may help you select the mode best suited to the input source selected. For example you may select Dolby Pro Logic II or Logic 7 for most ana- log inputs and Dolby Digital for inputs connected

to digital sources. In the case of inputs such as a CD Player, Tape Deck or Tuner, you may wish to set the mode to Stereo, if that is your preferred listen- ing mode for standard stereo sources, where it is unlikely that surround encoded material will be used. Alternatively, the 5 Channel Stereo or Logic 7 Music mode may also be a good choice for stereo-only source material.

It is easiest to complete the surround setup using the full-OSDon-screen menus. From the MASTER menu (Figure 1), press the ⁄/¤ but- tons Euntil the › cursor is next to the SURROUND SELECT menu. Press the Set Button Fso that the SURROUND SELECT menu (Figure 6) is on the screen.

* * S U R R O U N D S E L E C T * *

D O L B Y

S U R R

D T S

 

L O G I C

7

D S P ( S U R R )

V M A x

S T E R E O

B A C K T O M A S T E R M E N U

Figure 6

Each of the option lines on this menu (Figure 6) selects the surround mode category, and within each of those categories there will be a choice of the specific mode options. The choice of modes will vary according to the speaker configuration in your system.

When the SURR BACK line of the SPEAKER SETUP menu (Figure 5) is set to NONE the AVR will be configured for 5.1-chan- nel operation, and only the modes appropriate to a five-speaker system will appear.

When the SURR BACK line of the SPEAKER SETUP menu (Figure 5) is set to SMALL or LARGE the AVR will be configured for 6.1/7.1-channel operation, and additional modes such as Dolby Digital EX and 7 STEREO or Logic 7 7.1 will appear, as they are only available when seven main speakers are present. In addition, the modes DTS ES (Discrete) and DTS+NEO:6 (DTS ES Matrix) available in the AVR will not appear unless a digital source is playing the correct bitstream.

Note: When a Dolby Digital or DTS source is selected and playing, the AVR will select the appropriate surround mode automatically, no matter which surround mode was selected for that input as default. Then no other surround modes will be available, except VMAx with Dolby Digital recordings and all Pro Logic II modes with Dolby Digital 2 channel (2.0) recordings (see page 34).

To select the mode that will be used as the initial default for an input, first press the ⁄/¤ buttons

Euntil the on-screen cursor is next to the desired mode’s master category name. Next, press

Page 23 Page 25
Image 24
Page 23 Page 25
Contents AVR 430 Audio/ Video Receiver Table of Contents Declaration of ConformityDescription and Features IntroductionIntroduction / Safety Information Important Safety InformationUnpacking Front Panel Controls Coaxial Ó For more informationRear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet Switched Outlet AC Power Cord Jack Connect the ACAVR 430 when appropriate upgrades are available + and negative terminalsMain Remote Control Functions Light ButtonMain Remote Control Functions SelectorChannel Direct Inputs the input Main Remote Control Functions Main Remote Control Functions Zone II Remote Control Functions Multi IR input jackInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Output jacksScart A/V Connections If you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersSystem and Power Connections Main Room Remote Control ExtensionAC Power Connections Multiroom IR LinkSpeaker Placement Speaker SelectionSystem Configuration Using the On-Screen DisplaySystem Setup Input SetupAudio Setup Component Video Inputs may beSet Button F Speaker Setup To bring up the Speaker Setup menu FigureOn the remote System Configuration Surround Setup Adjustments for Other Inputs Delay SettingsNight Mode Settings Output Level AdjustmentUsing EzSet Button on the remoteAn indication that the volume control was set too low Microphone Sensor at the topVolume until you can hear the test noise clearly Press the Clear ButtonSurround Mode Chart OperationNo delay available Mix of the in-phase material of the left and right channelsNo surround channels But no surround speakersBasic Operation Source SelectionChannel/8-Channel Direct Input Controls and Use of Headphones Surround Mode SelectionVolume Up/Down Buttons One of the most important featuresDigital Audio Playback Dolby DigitalPCM Audio Playback MP3 Audio PlaybackDigital Bitstream Indicators Speaker/Channel IndicatorsAudio, while the main feature is available Selecting a Digital SourceOutput Level Adjustment With Source Signals Night ModeTape Recording Puts for Tape OutputsMemory Backup Set Button Fto activate the Channel Adjust menu FigureDim Function Advanced Features Turn On Volume LevelSurround Amplifier Channel Assignment Front-Panel-Display FadeAdvanced Features / Multiroom Operation Semi-OSD SettingsFull-OSD Time Out Adjustment InstallationMultiroom Setup Multiroom OperationRS-232 Control At the Multi in line, press the ‹/› buttonsMultiroom Operation / Tuner Operation Basic Tuner OperationRDS Tuning Tuner OperationRDS Operation RDS Display OptionsConfiguring the Remote Preprogrammed Code EntryAppears Learning Commands Automatic Code EntryFappears Programming the Remote Changing DevicesMacro Programming Recording a MacroPunch-Through Configuration Power On VID 2/TV VID 3/Cable AVR Logic 7 OErasing a Macro Read a MacroVolume Punch-Through Returning the Volume Control Settings to Default OperationReturning the Channel Control Settings to Default Operation Channel Punch-ThroughEzSet Configuration Ezset Disable appears in the lower line of the LCD displayTransport Punch-Through ⁄¤ Navigation Buttons Eonce so thatRenaming Renaming a Device‹/› Navigation Buttons Eas required Renaming Individual KeysResetting the Remote At this point you have two optionsSee page 34 for more information Additional Notes on Configuring and Operating the Remote Troubleshooting Guide Processor ResetPower Switch 1 is pushed Press the AVR SelectorTechnical Specifications Harman Consumer International
Related manuals
Manual 52 pages 53.72 Kb

AVR 430 specifications

The Harman-Kardon AVR 430 is a versatile and powerful audio-video receiver that has made a significant mark in the world of home entertainment. Designed for audiophiles and casual listeners alike, the AVR 430 combines advanced technology with user-friendly features, making it an excellent choice for anyone looking to elevate their home theater experience.

One of the standout features of the AVR 430 is its multi-channel audio processing capability. It supports Dolby Digital and DTS surround sound formats, providing immersive audio that allows users to experience movies, music, and games in a whole new way. This receiver is equipped with 5.1 channel amplification, delivering a robust output of up to 70 watts per channel, ensuring that even the most demanding audio tracks come through with clarity and impact.

In terms of connectivity, the AVR 430 offers a range of input options. It includes multiple HDMI inputs that support high-definition video and audio, making it easy to connect modern devices such as Blu-ray players, gaming consoles, and streaming devices. It also features optical, coaxial, and analog inputs, providing compatibility with a variety of audio sources. Furthermore, the inclusion of a dedicated subwoofer output allows users to enhance their system with a powerful subwoofer for deeper bass response.

The AVR 430 is designed with user convenience in mind. It features an intuitive on-screen display that simplifies setup and navigation through various input sources and audio settings. The remote control is ergonomically designed and includes dedicated buttons for quick access to frequently used functions. One noteworthy technology embedded in this receiver is the proprietary Harman Kardon Logic 7 processing, which creates a wider soundstage and more realistic surround sound from stereo sources.

Additionally, the AVR 430 is built with high-quality components that ensure durability and longevity. Its sleek and stylish design allows it to seamlessly integrate into any home entertainment environment. The receiver is also known for its ability to maintain high audio fidelity, thanks to its high-current amplifier design and advanced digital circuitry.

In summary, the Harman-Kardon AVR 430 is an outstanding audio-video receiver that caters to both audiophiles and casual users. Its combination of powerful amplification, extensive connectivity options, intuitive controls, and high-quality sound processing technologies make it a top choice for anyone looking to upgrade their home theater system. Whether enjoying a blockbuster film or listening to favorite music tracks, the AVR 430 delivers an impressive audio experience that is sure to impress.
Top Page Image Contents