Harman-Kardon AVR 430 owner manual Speaker Selection, Speaker Placement

Page 19

Installation and Connections

The AVR draws significantly more current than other household devices such as computers that use removable power cords. For that reason, it is important that only the cord supplied with the unit (or a direct replacement of identical capa- city) be used.

Once the power cord is connected, you are almost ready to enjoy the AVR’s incredible power and fidelity!

Speaker Selection

No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers. This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers.

Speaker Placement

The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.

Depending on the type of center-channel speak- er in use and your viewing device, place the cen- ter speaker either directly above or below your TV, or in the center behind a perforated front- projection screen.

Once the center-channel speaker is installed, position the left-front and right-front speakers so that they are as far away from one another as the center-channel speaker is from the preferred listening position. Ideally, the front-channel speakers should be placed so that their tweeters are no more than 60cm above or below the tweeter in the center-channel speaker.

They should also be at least 0.5 meter from your TV set unless the speakers are magnetically shielded to avoid colourings on the TV screen. Note that most speakers are not shielded, even with complete surround sets only the Center speaker may be.

Depending on the specifics of your room acoustics and the type of speakers in use, you may find that imaging is improved by moving the front-left and front-right speakers slightly for- ward of the center-channel speaker. If possible, adjust all front loudspeakers so that they are aimed at ear height when you are seated in the listening position.

Using these guidelines, you’ll find that it takes some experimentation to find the correct loca- tion for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that audio transitions across the front of the room sound smooth.

When the AVR is used in 5.1-channel operation, the preferred location for surround speakers is on the side walls of the room, at or slightly behind the listening position. In a 7.1-channel system, both side surround and back surround speakers are required. The center of the speaker should face you (see below).

Rear surround speakers are required when a full 7.1-channel system is installed, and they may also be used in 5.1 channel mode as an alterna- tive mounting position when it is not practical to place the main surround speakers at the sides of the room. Speakers may be placed on a rear wall, behind the listening position. As with the side speakers, the center of the rear surrounds should face you. The speakers should be no more than 2 meters behind the rear of the seating area.

Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal loca- tion for a subwoofer is to begin by placing it in the front of the room, about 15cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.

Center Front Speaker

No more than 60cm

Left Front

 

Right Front

Speaker

 

Speaker

A)Front Channel Speaker Installation with Direct-View TV Sets or Rear-Screen Projectors

 

 

 

TV or Projection Screen

 

 

Left Front

Center Front

Right Front

 

Speaker

 

Speaker

Speaker

 

 

than 2m

-mounted

are used

 

 

No more

when rear

speakers

 

 

 

 

 

Optional Rear-Wall Mounting

 

B)The distance between the left and right

speakers should be equal to the distance from the seating position to the viewing screen. You may also experiment with placing the left and right speakers slightly forward of the center speaker.

Rear speaker mounting is an alternate location for 5.1 systems. It is required for 7.1 operation.

INSTALLATION AND CONNECTIONS 19

Image 19
Contents AVR 430 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesImportant Safety Information Introduction / Safety InformationUnpacking Front Panel Controls For more information Coaxial ÓDigital Audio Outputs Connect these Rear Panel ConnectionsSwitched Outlet AC Power Cord Jack Connect the AC Unswitched Outlet+ and negative terminals AVR 430 when appropriate upgrades are availableLight Button Main Remote Control FunctionsSelector Main Remote Control FunctionsChannel Direct Inputs the input Main Remote Control Functions Main Remote Control Functions Multi IR input jack Zone II Remote Control FunctionsOutput jacks Installation and ConnectionsAudio Equipment Connections Video Equipment ConnectionsScart A/V Connections Important Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aMultiroom IR Link System and Power ConnectionsMain Room Remote Control Extension AC Power ConnectionsSpeaker Selection Speaker PlacementInput Setup System ConfigurationUsing the On-Screen Display System SetupComponent Video Inputs may be Audio SetupSet Button F To bring up the Speaker Setup menu Figure Speaker SetupOn the remote System Configuration Surround Setup Delay Settings Adjustments for Other InputsButton on the remote Night Mode SettingsOutput Level Adjustment Using EzSetMicrophone Sensor at the top An indication that the volume control was set too lowPress the Clear Button Volume until you can hear the test noise clearlyOperation Surround Mode ChartBut no surround speakers No delay availableMix of the in-phase material of the left and right channels No surround channelsSource Selection Basic OperationChannel/8-Channel Direct Input One of the most important features Controls and Use of HeadphonesSurround Mode Selection Volume Up/Down ButtonsMP3 Audio Playback Digital Audio PlaybackDolby Digital PCM Audio PlaybackSelecting a Digital Source Digital Bitstream IndicatorsSpeaker/Channel Indicators Audio, while the main feature is availablePuts for Tape Outputs Output Level Adjustment With Source SignalsNight Mode Tape RecordingSet Button Fto activate the Channel Adjust menu Figure Memory BackupDim Function Front-Panel-Display Fade Advanced FeaturesTurn On Volume Level Surround Amplifier Channel AssignmentInstallation Advanced Features / Multiroom OperationSemi-OSD Settings Full-OSD Time Out AdjustmentAt the Multi in line, press the ‹/› buttons Multiroom SetupMultiroom Operation RS-232 ControlBasic Tuner Operation Multiroom Operation / Tuner OperationRDS Display Options RDS TuningTuner Operation RDS OperationPreprogrammed Code Entry Configuring the RemoteAppears Automatic Code Entry Learning CommandsFappears Changing Devices Programming the RemoteRecording a Macro Macro ProgrammingRead a Macro Punch-Through ConfigurationPower On VID 2/TV VID 3/Cable AVR Logic 7 O Erasing a MacroChannel Punch-Through Volume Punch-ThroughReturning the Volume Control Settings to Default Operation Returning the Channel Control Settings to Default Operation⁄¤ Navigation Buttons Eonce so that EzSet ConfigurationEzset Disable appears in the lower line of the LCD display Transport Punch-ThroughRenaming Individual Keys RenamingRenaming a Device ‹/› Navigation Buttons Eas requiredAt this point you have two options Resetting the RemoteSee page 34 for more information Additional Notes on Configuring and Operating the Remote Press the AVR Selector Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Harman Consumer International
Related manuals
Manual 52 pages 53.72 Kb

AVR 430 specifications

The Harman-Kardon AVR 430 is a versatile and powerful audio-video receiver that has made a significant mark in the world of home entertainment. Designed for audiophiles and casual listeners alike, the AVR 430 combines advanced technology with user-friendly features, making it an excellent choice for anyone looking to elevate their home theater experience.

One of the standout features of the AVR 430 is its multi-channel audio processing capability. It supports Dolby Digital and DTS surround sound formats, providing immersive audio that allows users to experience movies, music, and games in a whole new way. This receiver is equipped with 5.1 channel amplification, delivering a robust output of up to 70 watts per channel, ensuring that even the most demanding audio tracks come through with clarity and impact.

In terms of connectivity, the AVR 430 offers a range of input options. It includes multiple HDMI inputs that support high-definition video and audio, making it easy to connect modern devices such as Blu-ray players, gaming consoles, and streaming devices. It also features optical, coaxial, and analog inputs, providing compatibility with a variety of audio sources. Furthermore, the inclusion of a dedicated subwoofer output allows users to enhance their system with a powerful subwoofer for deeper bass response.

The AVR 430 is designed with user convenience in mind. It features an intuitive on-screen display that simplifies setup and navigation through various input sources and audio settings. The remote control is ergonomically designed and includes dedicated buttons for quick access to frequently used functions. One noteworthy technology embedded in this receiver is the proprietary Harman Kardon Logic 7 processing, which creates a wider soundstage and more realistic surround sound from stereo sources.

Additionally, the AVR 430 is built with high-quality components that ensure durability and longevity. Its sleek and stylish design allows it to seamlessly integrate into any home entertainment environment. The receiver is also known for its ability to maintain high audio fidelity, thanks to its high-current amplifier design and advanced digital circuitry.

In summary, the Harman-Kardon AVR 430 is an outstanding audio-video receiver that caters to both audiophiles and casual users. Its combination of powerful amplification, extensive connectivity options, intuitive controls, and high-quality sound processing technologies make it a top choice for anyone looking to upgrade their home theater system. Whether enjoying a blockbuster film or listening to favorite music tracks, the AVR 430 delivers an impressive audio experience that is sure to impress.