Harman-Kardon Explore the Functions and Features of the Harman Kardon AVR 745 Stereo Receiver
Page 13

29510_AVR745_Engelsk 30/10/06 9:31 Side 13

Zone II Remote Control Functions

GNumeric Keys: These buttons serve as a ten-button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, VCR or Sat receiver has been selected on the remote, or to select track num- bers on a CD, DVD or LD player, depending on how the remote has been programmed.

HDisc Skip: Press this button to change discs on compatible Harman Kardon CD or DVD changers.

IVolume Up/Down: When used in the room where the AVR is located, press this button to raise or lower the volume in that room. When it is used in a remote room with a sensor that is

connected to the Multi IR Jack , this button will raise or lower the volume in the remote room.

JBlank Buttons: These buttons are not active. Pressing them will not change or control any function on the AVR 745 or other IR devices.

KMute: When used in the room where the AVR is located, press this button to temporarily silence the unit. When it is used in a remote room with a sensor that is connected to the

Multi IR Jack , this button will temporarily silence the feed to the remote room only. Press the button again to return to the previous volume level.

Important Note: No matter in which room the Zone II remote is used, as with the main remote it is important to remember to press the Input Selector button D that corresponds to the unit you wish to operate befor you change the device to be controlled.

LClear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.

MDirect Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys G to select a station (See page 57 for more information on the tuner).

NMemory Button: Press this button to enter a radio station into the AVR’s preset memory. Two underline indicators will flash at the right side of the Main Information Display ˜, you then have five seconds to enter a preset memory location using the Numeric Keys G. (See page 57 for more information.)

OTuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so MANUAL appears in the Main Information Display ˜, pressing the Tuning buttons K will move the frequency up or down in single-step increments. When the FM band is in use and AUTO appears in the Main Information Display ˜, pressing this button will change to monaural reception making even week stations audible. (See page 57 for more information.)

PTransport Control Buttons: These buttons do not have any functions for the AVR, but they are programmed for the forward/reverse play operation of a wide variety of Harman Kardon CD or DVD players, and audio or video- cassette recorders.

QSet Button: This button is used to enter settings into the AVR’s memory. It is also used in the setup procedures for delay time, speaker con- figuration and channel output level adjustment.

 Digital Media Player (DMP) Selector: When Harman Kardon’s

(optional) is connected to Digital

Media Player (DMP) Connector

and a

compatible Apple® iPod® is docked in

 

,

 

pressing this selector will select the iPod as the audio source input device for the AVR 745. In addition, if a video display is connected to one of the Video Monitor Outputs , the iPod’s messages will appear on screen, and in the Upper and Lower Display Lines ˜. The ⁄/¤/‹/› Buttons DF, the Set Button EQ and the Transport Controls AP may be used to navigate the iPod and to operate many functions. See page 50, and the manuals for The Bridge and your iPod for more informa- tion.

ENGLISH

ZONE II REMOTE CONTROL FUNCTIONS 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents AVR 745 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesImportant Safety Information Introduction / Safety InformationUnpacking Front Panel Controls More information Coaxial ÓTo select between the Optical Surround Left Blue Surround Right Gray Surround Back Left Rear Panel ConnectionsSurround Back Right Tan Subwoofer LFE Digital AudioDigital Audio Outputs Connect these AC Power Cord Jack Connect the ACDigital recorder such as a CD-R or MiniDisc recorder Monitor Component Video Outputs+ and negative terminals AVR 745 when appropriate upgrades are availableRemote IR Carrier Output The output Main Remote Control Functions Power Button Press this button to turn a Device off Power Off B AVR Selector Zone II Remote Control Functions The Bridge /DMP Selector Tions of the AVR or any compatibleOptional is connected to Digital Audio Equipment Connections Installation and ConnectionsAnalog Video Equipment Connections Output jacksHdmi Input Connections Hdmi ConnectionsJacks Connection NotesScart A/V Connections Hdmi Output ConnectionsVideo 2 or Video 3 Video Audio Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters With Scart that cannot be switched and pro- vided by the AVRMain Room Remote Control Extension System and Power ConnectionsMultiroom IR Link Remote IR Carrier Output Jack . If youRS-232 Connections AC Power ConnectionsUSB Connections Trigger Jack ConnectionSpeaker Selection Speaker PlacementRemote Control Setup Using the On-Screen Display System ConfigurationFirst Turn On In/Out Setup System SetupSystem Configuration D E O Video Setup Video Monitor SettingsAdvanced Configuration menus to be active List of input source defaults isSettings available on Page 1 Advanced Configuration SettingsAdvanced Configuration menu are the following Surround Setup Audio SetupOn the ZR 10 remote Night Mode Settings Using EzSet/EQS I G N E P Ezset Design StepS E T On the ZR 10 remote to continueIf the sound is not to your liking, press AVRSpeaker Size Menu Manual SetupSpeaker Size Sub Mode Setting LFE Low-Pass-Filter SettingFollowing options are available Delay Settings Subwoofer ConfigurationSubwoofer Size Output Level Adjustment Setup Additional Input Adjustments EzSet/EQ II Preset SelectionOperation Surround Mode ChartChannel DTS-ES 6.1 DiscreteDTS Neo6 Cinema Channel presentation of two-channel stereo programsUsing the Sleep Timer Switched AC Outlets and the PowerBasic Operation Source SelectionOr Video 1 or 2 Component Inputs Controls and Use of HeadphonesOne of the most important features Surround Mode SelectionDigital Audio Playback Rear panel Dolby DigitalPCM Audio Playback Selecting a Digital SourceUSB Playback Digital Bitstream IndicatorsPanel Night Mode Speaker/Channel IndicatorsAudio, while the main feature is available Video Adjustments and Operation UsingDigital Audio Outputs Tape Recording Output Level AdjustmentFront Panel In/Outputs EzSet/EQ II OperationDim Function Memory BackupSubwoofer Control Turn On Volume Level Advanced FeaturesFront-Panel-Display Fade Display BrightnessFull-OSD Time Out Adjustment Semi-OSD SettingsDMP/ TheBridgeTM Auto Power Hdmi Video Auto FunctionMultiroom Setup InstallationMultiroom Operation Multiroom OperationInfrared Output Selection Recalling Preset Stations Preset TuningTuner Operation Basic Tuner OperationRDS Operation RDS TuningRDS Display Options Message after the individual time outProcessor Reset Troubleshooting GuidePower Switch 1 is pushed Press the AVR Selector BVideo Input Defaults System DefaultsVideo Source Defaults Worksheet C Delay Defaults and Setting Worksheet B Surround Configuration Defaults and SettingsWorksheet D System Defaults and Settings Video Video 3 Video Worksheet E Input SettingsTape Tuner Bridge Technical Specifications Harman Consumer Group, Inc
Top Page Image Contents