Refilling Your Steam Cleaner With Water

OPERATING INSTRUCTIONS

Refilling Your Steam Cleaner With Water

Step 1: Disconnect electrical power cord from wall outlet.

Step 2: Depress and hold the hand grip steam trigger to ensure that any remaining pressure in the boiler has been released.

Step 3: Carefully loosen the safety/filler cap by turning counter clockwise. Any residual steam will be released below the safety/filler cap if the tank has not been completely vented. When the hissing stops and the last of the steam has been released, remove the filler cap. Allow unit to cool down.

CAUTION: Allow unit to cool for 15 minutes before refilling. If the steam

Fig. 2

Fig. 3

NOTE: Fit floor brush with the angle adapter on to the extension tube.

Attaching a Towel to the Floor Brush

100% white terry cloth towel can be fitted on this brush, so as to absorb the dirt and protect delicate surfaces.

Important: Please note that bristles may break through thin towels. To cut and make your own towels, we recommend that you use one (1) towel 8” x 17” folded in half or two (2) towels 4” x 17” laid one on top of the other be used. This will ensure that the brush bristles do not break through and that the towels will be sufficiently absorbent and retain as much dirt as possible.

Very Important: When installing the towels to the floor brush, ensure that the towels do not cover the front and the back of the brush. (See Fig. 9)

Fig. 7

4.Fold the other side of the towel as shown in Fig. 7.

cleaner is still hot, there is a risk that water will squirt back during filling and cause scalding. Extreme care should be taken when refilling the unit. Use caution when opening the safety/filler cap as cap may become hot during use and escaping steam can cause scalding.

Step 4: Allow the steam cleaner to cool for 15 minutes before re-filling with water.

Step 5: Refill water tank with water using the filling funnel.

Step 6: Firmly screw the safety/filler cap back onto the unit by turning clockwise.

Step 7: Connect power cord to the wall outlet.

Using Your Steam Cleaner with Floor Brush

Step 1: Connect one of the extension tubes to the hand grip on the flexible steam hose. To attach the extension tubes one onto the other or

Step 2: If the angle adapter is not attached to the floor brush, hold the brush with its bristles up in your left hand. With the angle adapter pointing downward, insert it into the hole in the back of the brush, then turn the floor brush 180°.

Step 3: Insert the electrical power cord into the wall outlet. Heating time is approximately 8-10 minutes with cold water. Filling the steam generator with hot water will shorten the heat up time.

Note: If you require continuous steam, depress the trigger and engage the trigger lock. (Fig. 2)

Cleaning the Floor Brush

To clean the floor brush after you have finished using:

1.	Lift the front clip on the floor
2.	brush (Fig. 4) and remove the brush.
2.	Rinse the bristle brush and the
3.	diffuser housing under warm water.
3.	Replace bristle brush onto the diffuser

Fig. 5

1.Prepare white terry cloth towel:

size 8” x 17” folded in half or place one on top of another to have two layers. (Fig. 5)

2.Place the brush on top of the towel.

Fig. 8

5.Place the corner under the cloth holder as shown in Fig. 8.

Fig. 9

6.Place the towel around the brush, and repeat folding the towel as shown in Fig. 9. When folding the towel, leave some slack. Do not pull tightly around the brush, leave some looseness.

onto the hand grip, press the locking button ensuring that it fits into the hole. (Fig. 2, Fig. 3) To disconnect, repeat the operation by pressing the locking button and pulling the two sections apart.

housing.

Fig. 4

Fig. 6

3. Fold the towel as shown in Fig. 6.