Superior CFST-CMP Decorative Arch Kits, Gas Flex Line with Valve, Cleaning and Servicing

Decorative Arch Kits

Two arch kits are available for the CFST appli- ance. A one piece complete door arch kit and a four (4) piece arch frame kit. Both kits are easy to install and do not require hardware to attach them to the standard door frame. The four- piece arch frame kit can be installed without the bottom or bottom and side pieces to customize the look of your appliance. This kit can be retrofitted to previously installed CFST appli- ances. The decorative arches may not be used in conjunction with the screen panel kit.

Gas Flex Line with Valve

A gas flex line kit is available to aid in attaching the appliance to the gas supply. This kit can only be used where local codes permit. The kit includes a ¹⁄₂" NPT to ³⁄₈" flare in line shut-off valve, a 12" flex line ³⁄₈" female flare through and a ³⁄₈" flare to ³⁄₈" NPT fitting. The components of this kit are rated for both natural and propane gas. This kit is designed to be used as an aid in installing the appliance.

WARNING: CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES. USE CAUTION AROUND THE APPLIANCE TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE SUPER- VISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

OPERATION AND CARE OF YOUR APPLIANCE

1.Appliance operation may be controlled through the optional ON/OFF unit rocker switch, located in the lower control compartment, or through a remotely located optional wall switch or wall thermostat. Separate switches may pro- vide independent control for the forced air blower and remote fireplace operation (op- tional equipment).

2.These heater rated units are equipped with a two stage (HI, LOW) gas control valve. To cycle the burner between the HI and LOW settings, rotate the control knob, located in the center of the valve front face, clockwise and counter- clockwise respectively.

3.When lit for the first time, the appliance will emit a slight odor for an hour or two. This is due to the “burn-in” of the internal paints and lubricants used in the manufacturing process. Additionally, when lit for the first time, this appliance may produce smoke, this is normal and should be expected. For the first few hours, operate the appliance with doors and windows open to encourage the dissipation of smoke and fumes.

4.Upon each lighting of the appliance, conden- sation may occur and fog the inside of the glass panel. This condition will disappear shortly as the appliance heats.

5.Keep lower control compartment clean by vacuuming or brushing at least twice a year. More frequent cleanings may be required due to excessive lint from carpeting, bedding mate- rials, etc. It is important that the control com- partments, burners and circulating air pas- sageways of the heater be kept clean.

6.Always turn off gas to pilot before cleaning. Before relighting, refer to the lighting instruc- tions in this manual. Instructions are also found on a pull-out panel located on the floor of the appliance.

7.Always keep the appliance area clear and free from combustible materials, gasoline and other flammable liquids.

8.Remember, this appliance has a continuous burning pilot flame. Exercise caution when using products with combustible vapors.

CLEANING AND SERVICING

WARNING: TURN OFF THE UNVENTED GAS ROOM HEATER AND ALLOW TO COOL BEFORE CLEANING.

Only limited cleaning will be required under the normal use of the heater. Dust the front grate, the top of the piezo cover and the control knob occasionally. Do not use cleaning fluids to clean the logs or any other part of the room heater.

Remove the log assembly, gently handling by holding each log at each end. Use a vacuum cleaner to remove loose particles from the base and from around the burners. Gloves are rec- ommended to prevent the fibers from pricking your skin. If the skin is pricked, wash gently with soap and water. Replace the logs as de- tailed in Step 9 Assembling the Logs.

If, after a period of use, the flames start to exhibit unusual shapes and behavior, or the burners fail to ignite smoothly, then the burner holes may require some cleaning. If this hap- pens, it is preferable to contact your nearest dealer to get the appliance serviced.

REPLACEMENT PARTS

An exploded view of the room heater with numbered parts and a parts list can be found on pages 18 and 20. All parts should be or- dered through your Superior distributor or dealer. Parts will be shipped at prevailing prices at time of order.

When ordering repair parts, always give the following information:

1.The model number of the heater.

2.The serial number of the heater.

3.The part number.

4.The description of the part.

5.The quantity required.

6.The installation date of the heater.

If you encounter any problems or have any questions concerning the installation of this heater, please contact your distributor. For the name of your nearest distributor contact:

SFC

1110 West Taft Avenue

Orange, CA 92865

13