Harman-Kardon II manual For Wall-Mounting

Page 8

For Wall-Mounting

Note: The customer is responsible for the correct selection and use of mounting hardware (available through hardware stores) that will ensure the proper and safe wall-mounting of the speakers.

1.Remove the Modulus II from its box. Remove rubber cover from base and pull out Allen wrench. Use Allen wrench to remove mounting plate screw and remove mounting plate from base.

FIGURE 7

Adjustment

Screw

Allen Wrench

Housed

in Base

Rubber

Speaker

 

Cover

Base

 

Mounting Plate Screw

 

Mounting Plate

 

2.Secure the mounting plate to a wall stud using (4) #8-32 wood screws with a minimum 1-1/4" length. If fastened to wallboard with a minimum 1/2" depth, use #8 screws with plastic inserts or anchors. Do not mount directly to wallboard without plastic inserts or anchors designed for #8 screws. One of the mounting plates in the Modulus II system has a built-in bubble level. This mounting plate should be used as a template for mounting the mounting plates that do not include a bubble level.

2a. In cases where you would like to run the speaker wires through the wall, the mounting plate has a center hole for wire access.

FIGURE 8

WALL

Bubble Level

Hole in the Wall

#8-32 Wood

Screws (Not

Included)

Speaker Wires

3.Run speaker wires through base as shown below. Attach base to mounting plate by slipping the returns on underside of base into slots on the top of the mounting plate and hinging the base downward. Secure base by inserting and tightening mounting plate screw.Tighten adjustment screw, fixing the speaker into position.

FIGURE 9

Returns on

Underside of Base

Rubber Cover

Adjustment Screw

Allen Wrench

Speaker Wires

Viewed From Below

Note: Base Has Returns

 

That Grab Mounting Plate

 

 

4.Insert the Allen wrench back into holder in base and attach rubber cover.

4 MODULUS II HOME THEATER SYSTEM

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Modulus Home Theater System Read First Ii Modulus II Home Theater SystemTable of Contents Modulus II Home Theater SystemIntroduction TechnologyGraph Templates Unpacking the SystemSound-Level Meter Placement Planning Your SystemInstalling the Satellites For Shelf PlacementWall For Wall-MountingMay damage your equipment Turn Off All PowerSatellites ¡ R.A.B.O.S. On/Off Switch Subwoofer ControlsRear Panel Front Panel Few SuggestionsSet Low-Pass Filter § to On Subwoofer ConnectionsSet Low-Pass Filter § to Off Operation R.A.B.O.S. Kit Includes Following Components What R.A.B.O.S. DoesR.A.B.O.S. Goal Performing R.A.B.O.S.TestsR.A.B.O.S. Sound-Level Meter Rslm Contents of the R.A.B.O.S. Test CDRslm Placement Initial System-Level Setting Setting the Subwoofer Test LevelAdjusting the subwoofer levels for a 0dB peak Too Low When finished, press PauseLocating a test point Indicating an under-range testEffect of adjustable width Width B.O.S. Online What Does a Parametric Equalizer Do?Completing the Measurement Template These instructions are based on the example in FigureUsing the Width Selector Our example, you would enter 9 in the attenuation field LevelWhat You Measure,What To Do Skip to the Adjusting the R.A.B.O.S. Equalizersection on Modulus II Home Theater System Adjusting the R.A.B.O.S. Equalizer Table below illustrates all switch positions PositionMaintenance and Service Final System BalanceSpecifications Modulus II Home Theater System Satellite Center ChannelFrequency Width Modulus II Home Theater System Modulus II Home Theater System
Top Page Image Contents