Harman-Kardon AVR 2000 owner manual System Configuration, Speaker Selection, Speaker Placement

Page 17

System Configuration

When all audio, video and system connections have been made, there are a few configuration adjustments that must be made. A few minutes spent to correctly configure and calibrate the unit will greatly add to your listening experience.

Speaker Selection

No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers. This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers.

Speaker Placement

The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.

Depending on the type of center-channel speaker in use and your viewing device, place the center speaker either directly above or below your TV, or in the center behind a perforated front-projection screen.

Once the center-channel speaker is installed, position the left-front and right-front speakers so that they are as far away from one another as the center-channel speaker is from the preferred listening position. Ideally, the front-channel speakers should be placed so that their tweeters are no more than 60cm above or below the tweeter in the center-channel speaker.

They should also be at least 0.5 meter from your TV set unless the speakers are magnetically shielded to avoid colourings on the TV screen. Note that most speakers are not shielded, even with complete surround sets only the Center speaker may be.

Depending on the specifics of your room acoustics and the type of speakers in use, you may find that imaging is improved by moving the front-left and front-right speakers slightly forward of the center-channel speaker. If possible, adjust all front loudspeakers so that they are aimed at ear height when you are seated in the listening position.

Using these guidelines, you’ll find that it takes some experimentation to find the correct location for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that audio transitions across the front of the room sound smooth.

Surround speakers should be placed on the side walls of the room, at or slightly behind the listening position. The center of the speaker should face you.

If side-wall mounting is not practical, the speakers may be placed on a rear wall, behind the listening position. The speakers should be no more than two meters behind the rear of the seating area.

Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by placing it in the front of the room, about 15cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.

Center Front Speaker

No more than 60cm

Left Front

 

Right Front

Speaker

 

Speaker

A)Front Channel Speaker Installation with Direct-View TV Sets or Rear-Screen Projectors

 

 

 

TV or Projection Screen

 

 

Left Front

Center Front

Right Front

 

Speaker

 

Speaker

Speaker

 

 

than 2m

-mounted

are used

 

 

No more

when rear

speakers

 

 

 

 

 

Optional Rear-Wall Mounting

 

B)The distance between the left and right

speakers should be equal to the distance from the seating position to the viewing screen. You may also experiment with placing the left and right speakers slightly forward of the center speaker.

SYSTEM CONFIGURATION 17

Image 17
Contents AVR 2000 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesUnpacking Safety InformationImportant Safety Information 5 6 7 8 9 ! @ $ % Front Panel ControlsSee See page 29 for more information on tuning stationsFront Panel Information Display Dolby 3 Stereo Indicator Preset IndicatorFront Panel Information Display Digital Audio Outputs Connect these Rear Panel ConnectionsUnswitched Outlet 2000 Remote Control FunctionsHas been pressed Remote Control FunctionsRemote Control Functions Audio Equipment Connections Installation and ConnectionsVideo Equipment Connections Output jacksImportant Notes for S-Video connections Scart A/V ConnectionsImportant Note for Adapter Cables Remote Control Extension System and Power ConnectionsAC Power Connections Important Note for the Use SCART-Cinch AdaptersSpeaker Selection System ConfigurationSpeaker Placement Switched AC outlet Settings to be Made With Each Input UsedInput Setup Speaker SetupSystem Configuration Delay Settings Surround SetupOutput Level Adjustment To set the delay time, follow these stepsNight Mode Settings On the remote only, not the main volume controls Operation Controls and Use of HeadphonesBasic Operation Source SelectionSurround Mode Chart Digital Audio Playback Surround Mode SelectionDolby Digital PCM Audio PlaybackMP3 Audio Playback Digital Status IndicatorsSelecting a Digital Source Rear or front panel #$. In order to proRecord mode Night ModeTape Recording Or 2 OutputsMemory Backup Output Level Trim AdjustmentNormal output level adjustment for Volume ControlRecalling Preset Stations Preset TuningTuner Operation Station SelectionRDS Operation RDS TuningRDS Display Options Station’s frequencyOperation Direct Code Entry Programming the Remote with CodesMust be repeated first Auto-Search MethodProgramming the Remote Erasing Macro CommandsMacro Programming Press the AVR SelectorOperate the Volume Control Volume Punch-ThroughProgrammed Device Functions Remote With Other DevicesChannel Control Punch-Through Resetting the Remote MemoryTon , followed by the VID 2/TV Input Selector buttonAM/FM Function ListAVR DVD Setup Code Table TV 017 019 024 053 056 059 069 080 093 094 078 088 102040 091 020 022 043 075 076 077 078 092 102Setup Code Table VCR 054 155 045 047 085 090 112 135044 047 112 082 091 109 155Code Number 3digit List Setup Code Table CBLSetup Code Table CD Setup Code Table SAT Code Number 3 Digit List Setup Code Table DVDProcessor Reset Troubleshooting GuideTechnical Specifications Harman Consumer International

AVR 2000 specifications

The Harman-Kardon AVR 2000 is a versatile and powerful audio-video receiver designed to enhance your home entertainment experience. Engineered with cutting-edge technology, it delivers high-quality sound and video, making it a great choice for both audiophiles and casual listeners. The AVR 2000 emphasizes flexibility and connectivity, ensuring that it integrates seamlessly with a variety of components in your home theater setup.

One of the standout features of the AVR 2000 is its robust power output, with an impressive 100 watts per channel, which allows it to drive even the most demanding speakers with ease. This ensures that music enthusiasts can enjoy their favorite tracks with remarkable clarity and depth, while movie lovers can experience thrilling soundscapes that bring films to life.

The AVR 2000 supports a wide range of audio formats, including Dolby TrueHD and DTS-HD Master Audio, which are essential for delivering rich, cinematic sound. Whether you are playing a Blu-ray disc, streaming music, or gaming, the AVR 2000 offers a dynamic audio experience that enhances every moment.

In terms of video capabilities, the AVR 2000 supports 4K Ultra HD resolution, ensuring compatibility with the latest high-definition content. It features advanced video processing through its built-in HDMI ports, which allow for multiple device connections with support for 3D and HDCP 2.2. This means you can easily connect your TV, gaming console, and streaming devices without compromising on visual quality.

Another noteworthy characteristic of the AVR 2000 is its user-friendly interface, designed to make navigation and operation straightforward, even for beginners. The receiver includes an intuitive remote control and on-screen display, which simplify the process of customizing audio settings and adjusting inputs.

Moreover, the AVR 2000 integrates seamlessly with various wireless technologies, including Bluetooth, allowing users to easily stream music from their smartphones and tablets. This modern connection option enhances versatility, enabling users to enjoy their personal playlists without the need for additional cables.

In conclusion, the Harman-Kardon AVR 2000 is a feature-rich audio-video receiver that combines powerful performance with modern connectivity options. With support for various audio formats, superior video capabilities, and user-friendly design, it stands out as an excellent addition to any home theater setup, providing an immersive entertainment experience for users of all kinds.