Maintenance

The ENVI-RO requires very little maintenance. Regular cartridge replacement is the only normal requirement, and a very important one. In typical service, the cartridge change-out schedules are as listed below.

Every 6 months

-Replace the SR cartridge:

•Open both by-pass valves.

•Remove power from system by unplugging power cord.

•Close the inlet valve.

•Follow instructions on the SR cartridge label. Place a bucket under the cartridge to catch any excess water that may spill from the head. Remove the old cartridge by turning the cartridge to the left until it stops and pulling it downward until it is free from its head.

•Remove the outer shrink-wrap and protective cap from the new SR cartridge.

•Align the lugs on the new cartridge with the slots in the head.

•Holding the head and cartridge firmly, press the cartridge upward into the head fully, and then turn the cartridge to the right until it stops.

•Disconnect 3/8” OD line from SR Cartridge to Booster Pump inlet at Booster Pump. Route line into bucket and secure. Plug-in power cord.

•Route a blue line from the 3/8” storage tank drain valve to drain temporarily. Open inlet valve. Open storage tank drain valve. Drain storage tank until system starts processing water. Close storage tank drain valve.

•Once a solid flow of water has been established, flush 1 gallon. Unplug power cord. Re-connect 3/8” OD line to Booster Pump inlet. Plug in power cord.

•Close both by-pass valves.

Every 12 months

– Sanitize the storage tank and lines:

•Refer to “Disinfection” section - steps 1-8, for sanitization procedure.

– Replace the RO cartridge:

•Open both by-pass valves.

•Remove power from system by unplugging power cord.

•Close the inlet valve.

•Follow instructions on the MR cartridge label. Place a bucket under the cartridge to catch any excess water that may spill from the head. Remove the old cartridge by turning the cartridge to the left until it stops and pulling it downward until it is free from its head.

•Remove the outer shrink-wrap and protective cap from the new MR cartridge.

•Align the lugs on the new cartridge with the slots in the head.

•Holding the head and cartridge firmly, press the cartridge upward into the head fully, and then turn the cartridge to the right until it stops.

•Remove both capillary restrictors temporarily.

•Route a blue line from the 3/8” storage tank drain valve to drain temporarily. Open inlet valve. Open storage tank drain valve. Plug-in power cord.

•Drain storage tank until system starts processing water. Once a solid flow of water has been established, flush 5 gallons from tank drain (about 10 minutes). Unplug power cord.

WARNING Do not use this product water! It may contain a preservative solution from the RO cartridge and should not be consumed!

•Re-install capillary tubes.

•Close both by-pass valves.

–Replace the Post Carbon cartridge:

• Open both by-pass valves.

• Remove power from system by unplugging power cord.

• Close the inlet and both outlet valves.

•Route a blue line from the 3/8” storage tank drain valve to drain temporarily. Open storage tank drain valve. Drain storage tank. Close storage tank drain valve.

•Follow instructions on the Post Carbon cartridge label. Place a bucket under the cartridge to catch any excess water that may spill when removing lines. Remove lines, note flow direction, then remove cartridge.

•Install new cartridge, in same flow direction as original cartridge. Connect lines.

•Plug-in power cord. Once a solid flow of water has been established, flush 5 gallons from tank drain.

•Close storage tank drain valve.

•Open the inlet and both outlet valves.

•Close both by-pass valves.

ENVI-RO specifications

The Everpure ENVI-RO is a revolutionary reverse osmosis water filtration system designed to deliver high-quality drinking water while ensuring exceptional taste, safety, and convenience. Ideal for residential settings, this advanced system employs cutting-edge technology to remove impurities, contaminants, and unwanted minerals, providing users with clean and refreshing water.

One of the standout features of the ENVI-RO is its multi-stage filtration process, which includes a pre-filter, reverse osmosis membrane, and post-filter. The pre-filter effectively captures larger particles and sediments, prolonging the life of the subsequent filters. The heart of the system, the reverse osmosis membrane, boasts a high rejection rate for a wide range of contaminants, such as chlorine, lead, fluoride, and nitrates, resulting in water that is not only pure but also tastes fantastic.

The post-filter further enhances the quality of the water by removing any remaining odors and tastes, ensuring that each drop is crisp and clean. The ENVI-RO system also features an integrated water storage tank that provides ample supply, delivering filtered water on demand. The tank is designed to minimize space, making it an ideal choice for kitchens with limited under-sink areas.

Another notable characteristic of the Everpure ENVI-RO is its ease of installation and maintenance. Designed with user-friendliness in mind, the system can be installed without the need for professional assistance, allowing homeowners to enjoy high-quality water quickly and efficiently. The filters are easily replaceable, and the system includes a convenient indicator light that alerts users when it’s time for a filter change, ensuring optimal performance at all times.

Durability and reliability are also key components of the ENVI-RO design. The system features high-quality materials that ensure long-lasting performance, coupled with a design that minimizes wastewater during the filtration process, making it an environmentally friendly choice.

Whether for cooking, drinking, or preparing beverages, the Everpure ENVI-RO provides a superior solution for families seeking the best in water quality. With its innovative technologies and user-centric features, the ENVI-RO system stands as a testament to Everpure's commitment to delivering clean, delicious water that enhances everyday living.