Piping/Tubing Connections

3.Refer to Figure 1 for mounting bracket details. Position the top row of holes 1-9/16" inches below the top of the processor when installed. Install the wall mount bracket to a suitable vertical surface. Use no less than 4 - #12 fasteners to secure the bracket to the surface.

4.Prepare to attach the processor to the wall mount bracket. Lift the processor and “hook” the metal lip of the processor backplate over the top edge of the wall mount bracket.

Go to step 6.

5.Measure and install 2 - #12 fasteners on 16" centers to engage the top edge of the processor backplate - leave 1/4" gap. Lift the processor and “hook” the key-hole slots on the processor backplate. Tighten the 2 fasteners.

6.Install 2 - #12 minimum fasteners in the 2" wide slots along the bottom edge of the processor backplate.

1.Refer to Figure 2 and the drawing on Page 14 for general views of the piping, with a description of major components and connection points. These major components and connections will be referred to in the following steps.

2.A parts kit has been provided, which includes valves and tees to configure a system by-pass. Assemble the parts to the system using the example shown in Figure 3.

3.Prepare the plumbing to accept the RO system.

Note: The product water tubing/piping and associated fittings connecting the RO product outlet to the equipment being serviced should be food grade material that meets NSF Standard 51 or 61 with a minimum pressure rating of 100-PSI. The product water may react with metal piping, creating a corrosive condition, in addition to imparting an objectionable taste. Plastic pipe or reinforced tubing are generally very good choices for RO water distribution materials. The size of the product water tubing/piping should be 3/8" ID minimum. Distances of 25 feet or greater from the RO to the equipment being serviced should be 1/2" ID minimum.

4.Shut-off the supply of water to the existing filtration system, and relieve pressure. Connect a line from the treated water outlet of the filtration system to the inlet of the ENVI-RO system.

5.Connect the appropriate size and type of tubing/piping and associated fittings to the corresponding ENVI-RO outlet connection. Route the line(s) to the equipment being serviced (i.e.; espresso, coffee, etc.). Close the inlet, outlet and by-pass valves. Apply pressure to the existing filtration system and place it back into service.

6.Check the storage tank pre-charge pressure. It should only be checked and adjusted when the storage tank is empty. A 30 psi pre-charge pressure is required.

7.Connect a 3/8" OD tube to the reject Y-connector (labeled WASTE) located in lower right corner of processor. Route the other end of the tubing to a drain nearby, securing it properly. Allow an air gap at the drain, following any applicable local and national codes. See Figures 2 and 4.

WARNING Refer to “Reject to Drain, Maximum” under RO Production in the Performance Table (page 8) to determine the maximum gallon per minute waste flow rate. Verify drain has ample capacity for this waste flow, plus all other sources of waste flow sharing this drain.

8.Locate the needle valve from the parts kit. Attach a short section of 3/8" tubing to this valve.

NOTE: This assembly will be used to adjust the system recovery in the following section, then removed.

9.Remove the 3/8" tube from the reject Y-connector and install the needle assembly between the reject Y-connector and 3/8" tube.

Figure 3. Inlet and Outlet Connections

INLET	TEAMER
	S	COFFEE
	S	COFFEE

Figure 4. Reject Y-Connector Detail

ENVI-RO specifications

The Everpure ENVI-RO is a revolutionary reverse osmosis water filtration system designed to deliver high-quality drinking water while ensuring exceptional taste, safety, and convenience. Ideal for residential settings, this advanced system employs cutting-edge technology to remove impurities, contaminants, and unwanted minerals, providing users with clean and refreshing water.

One of the standout features of the ENVI-RO is its multi-stage filtration process, which includes a pre-filter, reverse osmosis membrane, and post-filter. The pre-filter effectively captures larger particles and sediments, prolonging the life of the subsequent filters. The heart of the system, the reverse osmosis membrane, boasts a high rejection rate for a wide range of contaminants, such as chlorine, lead, fluoride, and nitrates, resulting in water that is not only pure but also tastes fantastic.

The post-filter further enhances the quality of the water by removing any remaining odors and tastes, ensuring that each drop is crisp and clean. The ENVI-RO system also features an integrated water storage tank that provides ample supply, delivering filtered water on demand. The tank is designed to minimize space, making it an ideal choice for kitchens with limited under-sink areas.

Another notable characteristic of the Everpure ENVI-RO is its ease of installation and maintenance. Designed with user-friendliness in mind, the system can be installed without the need for professional assistance, allowing homeowners to enjoy high-quality water quickly and efficiently. The filters are easily replaceable, and the system includes a convenient indicator light that alerts users when it’s time for a filter change, ensuring optimal performance at all times.

Durability and reliability are also key components of the ENVI-RO design. The system features high-quality materials that ensure long-lasting performance, coupled with a design that minimizes wastewater during the filtration process, making it an environmentally friendly choice.

Whether for cooking, drinking, or preparing beverages, the Everpure ENVI-RO provides a superior solution for families seeking the best in water quality. With its innovative technologies and user-centric features, the ENVI-RO system stands as a testament to Everpure's commitment to delivering clean, delicious water that enhances everyday living.