Harman-Kardon AVR 155 owner manual Between these two options with the Up/Down button n

Page 11

Main Remote Control Functions

E ‹ Button: This button is used to change the menu selection or setting during some of the setup procedures for the AVR.

FOK Button: This button is used to enter settings into the AVR’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.

GDigital Select: Press this button to assign one of the digital inputs ￿￿*Ó to a source. (See page 34 for more information on using digital inputs.)

HNumeric Keys: These buttons serve as a ten-button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, VCR or Sat receiver has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.

ITuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so MANUAL appears in the Main Information Display Ò, pressing the Tuning buttons K) will move the frequency up or down in single-step increments. When the FM band is in use and AUTO appears in the Main Information Display Ò, pressing this button will change to monaural reception making even week stations audible. (See page 41 for more information.)

JDirect Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys H to select a station (See page 41 for more information on the tuner).

KTuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode button I has been pressed or the Band button ! on the front panel was held pressed so that AUTO appears in the Main Information Display Ò, pressing either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the MANUAL appears in the Main Information Display Ò, pressing these buttons will tune stations in single-step increments. (See page 41 for more information.)

LOSD Button: Press this button to activate the On Screen Display (OSD) system used to set up or adjust the AVR’s parameters.

MDolby Mode Selector: This button is used to select one of the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes, Dolby 3 Stereo or Dolby Digital. Note that the Dolby Digital mode is only available with a digital input selected and the other modes only as long as a Dolby Digital source is not playing (except Pro Logic II with Dolby Digital 2.0 recordings, see page 35-36). See page 35 for the available Dolby surround mode options.

NDTS Digital Mode Selector: When a DTS source is in use the AVR will select the appropriate mode automatically and no other mode will be available. Pressing this button will display the mode currently selected by the AVR´s decoder, depending on the surround material played and the speaker setting. When a DTS source is not in use, this button has no function. (See page 36 for the available DTS options.)

OLogic 7 Selector: Press this button to select one of the available Logic 7 surround modes. (See page 36 for the available Logic 7 options.)

PTransport Control Buttons: These buttons do not have any functions for the AVR, but they may be programmed for the for- ward/reverse play operation of a wide variety of CD or DVD players, and audio or video- cassette recorders. (See page 43 for more information on programming the remote.)

QTone Mode : Pressing this button enables or disables the Balance, Bass and Treble tone controls. When the button is pressed so that the words TONE IN appear in the Main Information Display Ò, the settings of the Bass and Treble controls and of the Balance

control will affect the output signals, and may be adjusted with the ⁄/¤ Buttons $. When the button is pressed so that the words TONE OUT appear in the Main Information Display Ò, the output signal will be "flat", without any balance, bass or treble alteration. When pressing this button to make TONE IN or TONE OUT appear in the Display, switch

between these two options with the Up/Down button n.

Skip Up/Down Buttons: These buttons do not have a direct function with the AVR, but when used with a compatibly programmed CD or DVD player/changer they will change the tracks on the disc currently being played.

Stereo Mode Selector: Press this button to select a stereo playback mode. When the button is pressed so that DSP SURROUND OFF appears in the Main Information Display Ò, the AVR will operate in a bypass mode with true fully analog, two-channel left/right stereo mode with no surround process- ing or bass management as opposed to other modes where digital processing is used. When the button is pressed so that 5 CH STEREO appears, the stereo signal is routed to all five speakers, if installed. (See page 20-21 for more information on stereo playback modes).

DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the various DTS Neo:6 modes, which extract a five-channel surround field from two-channel program material (from PCM source or analog input signal). The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects the next mode.

Macro Buttons: Press these buttons to store or recall a “Macro”, which is a pre-pro- grammed sequence of commands stored in the remote. (See page 44 for more information on storing and recalling macros).

RDS Select Button: Press this button to display the various messages that are part of the RDS data system of the AVR’s tuner. (See page 42 for more information on RDS).

Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR’s memory. When CD or DVD is selected using the Input Selector button 4, these buttons may function as Slow Fwd/Rev (DVD) or ”+10” (CD, CDR).

Clear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.

ENGLISH

MAIN REMOTE CONTROL FUNCTIONS 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents AVR 155 Audio/VideoReceiver Declaration of Conformity Table of ContentsFront panel analog A/V inputs Description and FeaturesIntroduction Unpacking Safety InformationImportant Safety Information ‹ Stereo Modes ‹ Logic 7 Modes Headphone Jack $ Speaker/Channel Input IndicatorFront Panel Controls See page 35 for more information on the Channel Indicators # Preset Stations Selector Press thisRear Panel Connections Main Power Switch Main Remote Control Functions See page 23-24 for more information Between these two options with the Up/Down button n Main Remote Control Functions Connect the analog output of a CD player to the CD inputs Installation and ConnectionsAudio Equipment Connections Video Equipment ConnectionsScart A/V Connections Hdmi ConnectionsSCART-Cinch Adapters Important Note for Adapter CablesImportant Notes for S-Video connections Important Note for the UseSpeaker Selection Speaker PlacementFirst Turn On System ConfigurationUsing the On-Screen Display System SetupCoax Input SetupSource Input Default Digital Audio Input › Navigation Button‹/› Navigation Buttons E Surround SetupSetting to your taste Night Mode SettingsStereo-Digital Mode Configuring the Surround Off Stereo ModesAutomated Speaker Setup Using EzSet/EQ Stereo-Direct Bypass ModeSystem Configuration OK Button F So that the on-screen cursor is pointing to‹/› Navigation Buttons E to Manual SetupSpeaker Setup With any movie input sourceSubwoofer ‹/› Navigation Buttons E to choose the appropriate setting ‹ / › Navigation Button E to enter Delay Settings¤ Button D once to move to the next line Output Level Adjustment Until the word OFF appears to stop the test tone Is then pressed to select OFF in the highlighted videoVolume until you can hear the test noise clearly Maximum bass impact Surround Mode ChartOperation Main speakers and a subwoofer Dolby 3 StereoReference WideChannel Direct Input Controls and Use of HeadphonesBasic Operation Source SelectionDolby Digital Surround Mode SelectionDigital Audio Playback Repeatedly to scroll through the list of available modesSelecting a Digital Source Surround Mode TypesDigital Bitstream Indicators PCM Audio PlaybackIncoming Bitstream Available Surround Modes Speaker/Channel IndicatorsPCM Playback Indications See FigureDSP Surround Off Night ModeIncoming Signal Available Surround Modes DTS, DTS StereoTo change the output level Output Level Adjustment With Source SignalsTo the Channel Reset line and press Tape RecordingButton as needed until the displays are on Memory BackupDim Function Front-Panel-Display Fade System SetupTurn On Volume Level Semi-OSD SettingsTo exit the menu system Full-OSD Time Out AdjustmentDefault Surround Mode Full-OSD Background ColorBasic Tuner Operation Tuner OperationProgram Search PTY RDS TuningRDS Operation RDS Display OptionsDirect Code Entry Programming the RemoteProgramming the Remote with Codes Code ReadoutProgrammed Device Functions Volume Punch-ThroughMacro Programming Channel Control Punch-Through Resetting the Remote MemoryVID 1 VCR Function ListAVR DVD Remote sensor Ú is obscured Troubleshooting GuideProcessor Reset Power Switch 2 is pushedTechnical Specifications Appendix Settings Worksheet Center Speaker Size Table A4 Source Input SettingsHarman Consumer Group, Inc
Related manuals
Manual 52 pages 9.23 Kb

AVR 155 specifications

The Harman-Kardon AVR 155 is a compact yet powerful AV receiver designed to enhance your home entertainment experience. Renowned for its exceptional audio quality and user-friendly interface, the AVR 155 caters to both casual listeners and audiophiles alike.

One of the key features of the AVR 155 is its ability to deliver robust multi-channel audio. It comes equipped with a 5.1 channel setup, allowing you to immerse yourself in surround sound while enjoying movies, music, or gaming. With a total power output of 375 watts, the AVR 155 can drive a variety of speakers efficiently, ensuring clear, dynamic sound reproduction across frequencies.

The AVR 155 also supports high-definition audio formats. It is compatible with Dolby TrueHD and DTS-HD Master Audio, allowing for a rich listening experience that takes full advantage of modern soundtracks. This support for high-resolution audio formats highlights Harman-Kardon's commitment to quality and performance.

In addition to its audio capabilities, the AVR 155 features multiple HDMI inputs, enabling you to easily connect various media devices such as Blu-ray players, gaming consoles, and streaming devices. It is equipped with HDMI 1.4, which supports 3D playback and allows for 4K pass-through, making it a future-proof choice for your home theater system.

Another standout feature is the built-in proprietary Harman GreenEdge technology, which focuses on energy efficiency while maintaining performance. This not only minimizes power consumption but also contributes to a more sustainable home environment.

The AVR 155 boasts an intuitive on-screen display through its user interface, making navigation of settings and options straightforward. With options to customize sound settings, including bass management and room correction, users have complete control over their listening environment.

With its sleek design, the Harman-Kardon AVR 155 seamlessly blends into any home theater setup. The combination of solid build quality and advanced technologies positions it as a great choice for anyone looking to elevate their audio experience without sacrificing space or style.

Overall, the Harman-Kardon AVR 155 stands out for its high-quality sound performance, multiple connectivity options, and energy efficiency, making it an excellent choice for modern home entertainment enthusiasts.
Top Page Image Contents