Harman-Kardon AVR 155 owner manual Speaker Selection, Speaker Placement

Page 16

Installation and Connections

Speaker Selection

No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers. This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers.

Speaker Placement

The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.

Depending on the type of center-channel speaker in use and your viewing device, place the center speaker either directly above or below your TV, or in the center behind a perforated front-projection screen.

Once the center-channel speaker is installed, position the left-front and right-front speakers so that they are as far away from one another as the center-channel speaker is from the preferred listening position. Ideally, the front-channel speakers should be placed so that their tweeters are no more than 60cm above or below the tweeter in the center-channel speaker.

They should also be at least 0.5 meter from your TV set unless the speakers are magnetically shielded to avoid colourings on the TV screen. Note that most speakers are not shielded, even with complete surround sets only the Center speaker may be.

Depending on the specifics of your room acoustics and the type of speakers in use, you may find that imaging is improved by moving the front-left and front-right speakers slightly for- ward of the center-channel speaker. If possible, adjust all front loudspeakers so that they are aimed at ear height when you are seated in the listening position.

Using these guidelines, you’ll find that it takes some experimentation to find the correct location for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that audio transitions across the front of the room sound smooth.

When the AVR is used in 5.1-channel operation, the preferred location for surround speakers is on the side walls of the room, at or slightly behind the listening position.

Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by placing it in the front of the room, about 15 cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.

A)Front Channel Speaker Installation with Direct-View TV Sets or Rear-Screen Projectors

5.1-Channel System

At least 15 cm from celling

At least 60 cm

16INSTALLATION AND CONNECTIONS

Page 15 Page 17
Image 16
Page 15 Page 17
Contents AVR 155 Audio/VideoReceiver Table of Contents Declaration of ConformityIntroduction Description and FeaturesFront panel analog A/V inputs Important Safety Information Safety InformationUnpacking Front Panel Controls Headphone Jack $ Speaker/Channel Input Indicator‹ Stereo Modes ‹ Logic 7 Modes # Preset Stations Selector Press this See page 35 for more information on the Channel IndicatorsRear Panel Connections Main Power Switch Main Remote Control Functions See page 23-24 for more information Between these two options with the Up/Down button n Main Remote Control Functions Installation and Connections Audio Equipment ConnectionsVideo Equipment Connections Connect the analog output of a CD player to the CD inputsHdmi Connections Scart A/V ConnectionsImportant Note for Adapter Cables Important Notes for S-Video connectionsImportant Note for the Use SCART-Cinch AdaptersSpeaker Placement Speaker SelectionSystem Configuration Using the On-Screen DisplaySystem Setup First Turn OnInput Setup Source Input Default Digital Audio Input› Navigation Button CoaxSurround Setup Setting to your tasteNight Mode Settings ‹/› Navigation Buttons EConfiguring the Surround Off Stereo Modes Automated Speaker Setup Using EzSet/EQStereo-Direct Bypass Mode Stereo-Digital ModeSystem Configuration So that the on-screen cursor is pointing to OK Button FManual Setup Speaker SetupWith any movie input source ‹/› Navigation Buttons E toSubwoofer ‹/› Navigation Buttons E to choose the appropriate setting ¤ Button D once to move to the next line Delay Settings‹ / › Navigation Button E to enter Output Level Adjustment Is then pressed to select OFF in the highlighted video Until the word OFF appears to stop the test toneVolume until you can hear the test noise clearly Operation Surround Mode ChartMaximum bass impact Dolby 3 Stereo ReferenceWide Main speakers and a subwooferControls and Use of Headphones Basic OperationSource Selection Channel Direct InputSurround Mode Selection Digital Audio PlaybackRepeatedly to scroll through the list of available modes Dolby DigitalSurround Mode Types Digital Bitstream IndicatorsPCM Audio Playback Selecting a Digital SourceSpeaker/Channel Indicators PCM Playback IndicationsSee Figure Incoming Bitstream Available Surround ModesNight Mode Incoming Signal Available Surround ModesDTS, DTS Stereo DSP Surround OffOutput Level Adjustment With Source Signals To the Channel Reset line and pressTape Recording To change the output levelDim Function Memory BackupButton as needed until the displays are on System Setup Turn On Volume LevelSemi-OSD Settings Front-Panel-Display FadeFull-OSD Time Out Adjustment Default Surround ModeFull-OSD Background Color To exit the menu systemTuner Operation Basic Tuner OperationRDS Tuning RDS OperationRDS Display Options Program Search PTYProgramming the Remote Programming the Remote with CodesCode Readout Direct Code EntryMacro Programming Volume Punch-ThroughProgrammed Device Functions Resetting the Remote Memory Channel Control Punch-ThroughFunction List VID 1 VCRAVR DVD Troubleshooting Guide Processor ResetPower Switch 2 is pushed Remote sensor Ú is obscuredTechnical Specifications Appendix Settings Worksheet Table A4 Source Input Settings Center Speaker SizeHarman Consumer Group, Inc
Related manuals
Manual 52 pages 9.23 Kb

AVR 155 specifications

The Harman-Kardon AVR 155 is a compact yet powerful AV receiver designed to enhance your home entertainment experience. Renowned for its exceptional audio quality and user-friendly interface, the AVR 155 caters to both casual listeners and audiophiles alike.

One of the key features of the AVR 155 is its ability to deliver robust multi-channel audio. It comes equipped with a 5.1 channel setup, allowing you to immerse yourself in surround sound while enjoying movies, music, or gaming. With a total power output of 375 watts, the AVR 155 can drive a variety of speakers efficiently, ensuring clear, dynamic sound reproduction across frequencies.

The AVR 155 also supports high-definition audio formats. It is compatible with Dolby TrueHD and DTS-HD Master Audio, allowing for a rich listening experience that takes full advantage of modern soundtracks. This support for high-resolution audio formats highlights Harman-Kardon's commitment to quality and performance.

In addition to its audio capabilities, the AVR 155 features multiple HDMI inputs, enabling you to easily connect various media devices such as Blu-ray players, gaming consoles, and streaming devices. It is equipped with HDMI 1.4, which supports 3D playback and allows for 4K pass-through, making it a future-proof choice for your home theater system.

Another standout feature is the built-in proprietary Harman GreenEdge technology, which focuses on energy efficiency while maintaining performance. This not only minimizes power consumption but also contributes to a more sustainable home environment.

The AVR 155 boasts an intuitive on-screen display through its user interface, making navigation of settings and options straightforward. With options to customize sound settings, including bass management and room correction, users have complete control over their listening environment.

With its sleek design, the Harman-Kardon AVR 155 seamlessly blends into any home theater setup. The combination of solid build quality and advanced technologies positions it as a great choice for anyone looking to elevate their audio experience without sacrificing space or style.

Overall, the Harman-Kardon AVR 155 stands out for its high-quality sound performance, multiple connectivity options, and energy efficiency, making it an excellent choice for modern home entertainment enthusiasts.
Top Page Image Contents