Harman-Kardon Maximize Your Audio Experience with Harman Kardon AVR 147's Surround Sound Configuration and NSP Mode
Page 20

System Configuration

When Dolby Pro Logic II Music is selected as the listening mode, three special settings are available to tailor the sound field to your listening room environment and your individual taste and preferences. (When other Dolby Surround modes are selected, dotted lines will indicate that these settings are not active.)

•Center Width: This setting adjusts the balance of the vocal information in the front soundstage between the center and front left/right speakers. The lower settings spread the center channel sound more broadly into the left and right channels. A higher number (up to “7”) produces a tighter center channel presentatioin.

•Dimension: This setting alters the perceived depth of the surround field by creating a shallower presentation that appears to move sounds toward the front of the room, or a deeper presentation that appears to move the center of the sound field toward the back of the room. The setting of “0” is a neutral default, with the range of adjustment shown as “R-3” for a deeper, rear-oriented sound to “F-3” for a shallower, front-oriented sound.

•Panorama: Switch this setting on or off to add an enveloping wrap-around presentation that increases the perception of sound along the sides of the room.

To change these parameters, press the ⁄/¤ Navigation Buttons D while the DOLBY SURROUND menu is on the screen until the

➞cursor is pointing to the line on the menu with the parameter you wish to change. Then, press

the ‹/› Navigation Buttons E

to alter

the setting to your taste.

 

Note that when the Dolby Digital mode is selected there are additional settings available for the Night mode that are associated with the surround mode only, not with the input. That´s why these settings must be made only once, not with each input in use.

Night Mode Settings

The Night mode is a feature of Dolby Digital that uses special processing to preserve the dynamic range and full intelligibility of a movie sound track while reducing the peak level.

This prevents abruptly loud transitions from disturbing others, without reducing the sonic impact of a digital source. Note that the Night mode is only available when the Dolby Digital surround mode is selected.

To adjust the Night mode setting from the menu press the OSD Button L so that the MASTER menu appears. Then press the ¤ button D to access the SURROUND SETUP menu. Press Set F to select the DOLBY menu.

To adjust the Night mode setting, make certain that the ➞ cursor is on the NIGHT line of the DOLBY menu. Next, press ‹/› Buttons

20SYSTEM CONFIGURATION

Eto choose between the following set-

tings.

OFF: When OFF is highlighted, the Night mode will not function.

MID: When MID is in the highlighted video, a mild compression will be applied.

MAX: When MAX is in the highlighted video, a more severe compression algorithm will be applied.

When you want to use the Night mode feature, we recommend that you select the MID setting as a starting point and change to the MAX setting later, if desired.

Note that the Night mode may be adjusted direct- ly any time that Dolby Digital surround mode is selected by pressing the Night button B. When the button is pressed, the words D-RANGEfollowed by the current setting (MID, MAX, OFF) will appear in the lower third of the video screen and in the Main Information Display Ò. Press the ⁄/¤ buttons D within five seconds to select the desired setting, then press Set F to confirm the setting.

On the DTS menu, the selection choices made with the ‹ / › Buttons E on the remote are determined by the type of DTS program material in use.

When the 5.1 configuration is in use the AVR will automatically select the 5.1 version of DTS processing when a DTS data stream is received.

When a DTS 96/24 signal is detected, the

AVR 147 defaults to the DTS surround mode, but reproduces the higher-resolution materials that are present due to the higher sampling rate automatically. See page 30 and 31 for a complete explanation of the DTS modes.

On the LOGIC 7 menu, the selection choices made with the ‹ / › Buttons E on the remote enable Harman Kardon’s exclusive Logic 7 processing to create fully enveloping, multi- channel surround from either two-channel Stereo or Matrix-encoded programming such as VHS cassettes, laserdiscs or television broadcasts produced with Dolby surround.

You may select the Logic 7/5.1 Music, Cinema or Enhanced modes. They work best with two-chan- nel music, surround-encoded programs or standard two-channel programming of any type, respectively. Note that the Logic 7 modes are not available when either Dolby Digital or DTS Digital soundtracks are in use.

On the DSP (SURR) menu, the selection choices made with the ‹ / › Buttons E on the remote select one of the DSP surround modes that are designed for use with two-channel stereo programs to create a variety of sound field presentations. The choices available are Hall 1,

Hall 2, Theater. The Hall and Theater modes are designed for multichannel installations. See pages 30-31 for a complete explanation of the DSP surround modes. Note that the Hall and Theater modes are not available when a Dolby Digital or DTS soundtrack is played.

On the STEREO menu, the selection choices made with the ‹ / › Buttons E on the remote may either turn the surround processing off for a traditional two-channel stereo presen- tation, or select 5 CH Stereo. The latter modes feed the stereophonic input signal to both front speakers, to the rear speakers and to both surround back speakers (if in use), while the monophonic signal parts are spread over all speakers, also the Center. See page 30-31 for a complete explanation of the 5 CH Stereo modes.

After the selections are made in the Dolby, DTS, Logic 7, DSP (Surround) or Stereo menus, press the ⁄/¤ buttons D so that the cursor moves to the BACK TO SURR SELECT line and presss the Set Button F.

Configuring the Surround Off (Stereo) Modes

For superior reproduction of two-channel program materials, the AVR offers two Stereo modes: an analog Stereo-Direct mode that bypasses the digital signal processing circuitry for a completely analog signal path that preserves the purity of the original signal, and a digital mode that is capable of providing bass management for optimal distribution of the low frequencies between smaller speakers and a subwoofer.

Stereo-Direct (Bypass) Mode

When the analog Stereo-Direct mode is selected by pressing the Stereo Mode Selector

until SURROUND OFF appears in the Main Information Display Ò and the Surround Mode Indicator ( for Surround Off is lit, the AVR will pass the analog source material directly through to the front left and right speakers, bypassing the digital processing circuitry.

In this mode, the front left and right speakers will automatically be configured as LARGE; it is not possible to configure these speakers as SMALL.

When the AVR is in the Stereo Bypass mode you may still configure the subwoofer output so that it is either turned off, with a full-range signal going to the front left/right speakers, or you may configure it so that the subwoofer feed is activated.

The factory default setting is to have the subwoofer turned off for this mode, but you may change that setting by following these steps:

1. Press the Speaker Button 6

.

2.Press the Set Button F@ to activate the configuration menu.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents AVR 147 Audio/ Video Receiver Table of Contents Declaration of ConformityDescription and Features IntroductionFive channels of high-current amplification Front panel analog A/V inputsUnpacking Safety InformationImportant Safety Information Headphone Jack $ Speaker/Channel Input Indicator Front Panel ControlsDigital Input Selector When playing a # Preset Stations Selector Press thisSee page 35 for more information on the Channel Indicators Rear Panel Connections Rear Panel Connections Main Remote Control Functions See page 23-24 for more information Main Remote Control Functions Main Remote Control Functions Installation and Connections Audio Equipment ConnectionsVideo Equipment Connections Connect the analog output of a CD player to the CD inputsHdmi Connections Scart A/V ConnectionsPower Connections AC Power ConnectionsImportant Note for Adapter Cables Important Notes for S-Video connectionsSpeaker Placement Speaker SelectionSystem Configuration Using the On-Screen DisplaySystem Setup First Turn OnInput Setup Source Input Default Digital Audio Input› Navigation Button CoaxSurround Setup Configuring the Surround Off Stereo Modes Night Mode SettingsStereo-Direct Bypass Mode ‹/› Navigation Buttons ETo take advantage of this feature, press Automated Speaker Setup Using EzSet/EQStereo-Digital Mode System Configuration Set Button F Manual SetupSpeaker Setup System Configuration Subwoofer ¤ Button D once to move to the next line ‹/› Navigation Buttons E to choose the appropriate settingDelay Settings Output Level Adjustment ‹ / › Navigation Button E to enterVolume until you can hear the test noise clearly When all channels have the same output levelIs then pressed to select OFF in the highlighted video Until the word OFF appears to stop the test toneSystem Configuration Maximum bass impact Surround Mode ChartOperation Dolby 3 Stereo ReferenceWide Main speakers and a subwooferControls and Use of Headphones Basic OperationSource Selection Channel Direct InputSurround Mode Selection Digital Audio PlaybackRepeatedly to scroll through the list of available modes Until Surr OFF appears in the Main Information Display ÒSurround Mode Types Digital Bitstream IndicatorsPCM Audio Playback Selecting a Digital SourceSpeaker/Channel Indicators PCM Playback IndicationsSee Figure Incoming BitstreamIncoming Bitstream Available Surround Modes Night ModeIncoming Signal Available Surround Modes Using Tape RecordingOutput Level Adjustment With Source Signals Memory BackupTo change the output level Dim FunctionSystem Setup Turn On Volume LevelSemi-OSD Settings Front-Panel-Display FadeFull-OSD Time Out Adjustment Default Surround ModeFull-OSD Background Color To exit the menu systemTuner Operation Basic Tuner OperationRDS Tuning RDS OperationRDS Display Options Program Search PTYProgramming the Remote Programming the Remote with CodesCode Readout Direct Code EntryProgrammed Device Functions Volume Punch-ThroughMacro Programming Resetting the Remote Memory Channel Control Punch-ThroughFollowed by the AVR Input Selector Button , followed by the same InputFunction List DVDAVR DVD Troubleshooting Guide Processor ResetPower Switch 1 is pushed Remote sensor Ú is obscuredTechnical Specifications Center Speaker Size Comp VVideo Table A4 Source Input Settings Harman Consumer Group, Inc
Related manuals
Manual 68 pages 55.01 Kb Manual 2 pages 42.45 Kb

AVR 147 specifications

The Harman-Kardon AVR 147 is an entry-level receiver designed for those who seek quality audio and video experiences without overcomplicating their setup. This model is part of Harman-Kardon's well-known line of audio-video receivers, designed to provide an immersive home theater experience.

At the heart of the AVR 147 is its 5.1 channel surround sound capability, allowing for the connection of up to five speakers plus a subwoofer. This configuration enables a rich sound field that envelops listeners, ideal for both movies and music. The receiver can deliver up to 40 watts per channel, providing sufficient power for a modest home theater setup. The incorporation of Dolby Digital and DTS decoding ensures that users can enjoy their favorite movies with cinematic sound quality.

One of the main features of the AVR 147 is its user-friendly interface. The simplified remote control and intuitive on-screen menu make it easy for users to navigate settings and optimize sound performance. The receiver also offers multiple inputs, including HDMI, component, composite, and optical connections, ensuring compatibility with a wide range of audio and video sources, such as Blu-ray players, gaming consoles, and streaming devices.

The AVR 147 is equipped with Harman Kardon’s proprietary technologies, including the Advanced DSP (Digital Signal Processing), which enhances audio quality and clarity. Moreover, it supports various surround sound formats, allowing users to enjoy an enhanced home theater experience tailored to their preferences.

Another noteworthy characteristic is its sleek, modern design, which blends seamlessly into any entertainment setup. With its front panel display, users can easily see their settings and selections. The robust build quality of the AVR 147 ensures durability and longevity, making it a wise investment for those passionate about audio-visual technology.

In terms of video accessories, the AVR 147 can upscale standard-resolution video sources to provide a better viewing experience. Although it lacks some of the advanced features found in higher-end models, the AVR 147 remains a commendable choice for anyone seeking an effective and powerful home theater solution without excessive complexity. Whether you're watching movies, playing video games, or enjoying your favorite music, the Harman-Kardon AVR 147 is a reliable companion in elevating home entertainment experiences.
Top Page Image Contents