GE GXSF39E, GXSF35E installation instructions Installation instructions, Unpacking and Inspection

Page 3

Installation instructions.

GEAppliances.com

CAUTION: Certain plumbing skills are needed for installation. If you are unsure about any part of the installation of this product, consult a professional plumber.

Unpacking and Inspection

Be sure to check the entire softener for any shipping damage or parts loss. Also note damage to the shipping cartons. Contact the transportation company for all damage and loss claims. The manufacturer is not responsible for damages in transit.

Small parts needed to install the softener are packaged either in a bag or on a cardboard sheet. To avoid loss of the small parts, keep them packaged until you are ready to use them. Be sure not to discard components hidden in packaging.

Important Installation Recommendations

Read entire manual. Failure to follow all guidelines and rules could cause personal injury or property damage.

Before you begin installation, read these Installation Instructions completely. Then, obtain all the materials and tools you will need to make the installation. Failure to properly install the softener voids the warranty.

Check local codes. The installation must conform to them.

In the Commonwealth of Massachusetts, Plumbing Code 248 CMR shall be adhered to. Consult with your licensed plumber.

Use only lead-free solder and flux for all sweat-solder connections, as required by state and federal codes.

Connect the softener to the main water supply pipe before or ahead of the water heater. DO NOT RUN HOT WATER THROUGH THE SOFTENER. Temperature of water passing through the softener must be less than 120°F.

Use care when handling the softener. Do not turn upside down, drop, drag or set on sharp protrusions.

Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve if necessary. (Adding a pressure reducing valve may reduce the flow.)

The softener works on 24 volt-60 Hz electrical power only. Be sure to use the included transformer. Be sure the electric outlet and transformer are in an inside location to protect from moisture.

See Where to Install the Softener section for more details.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. The water should be tested periodically to verify that the system is performing satisfactorily.

Small parts remaining after the installation could be a choke hazard. Discard safely.

3

Image 3
Contents Write the model and serial numbers here Model # Serial # 7247174 215C1173P010 49-5015102-05 JRSafety Precautions Installation instructions Important Installation RecommendationsUnpacking and Inspection Plan How You Will Install the Softener Where to Install the SoftenerTools and Materials Required for Installation Typical Installation Illustration Optional 3-Valve Bypass Installation IllustrationGEAppliances.com Step-by-step installation instructions Install Bypass ValvePlumb in and OUT Pipes to and from Softener With local codes 4A. Connecting a Rigid Valve Drain TubeInstall the Brine Tank Overflow Fittings and Hose Connect and RUN the Valve Drain HoseInstall Grounding Clamp Connect to Electrical PowerADD Water and Salt to the Brine Tank SET Recharge Starting Time Programming the ControlSET Water Hardness Number Salt TimeDays to EMPTY. Recharge SET Salt LevelDays to Empty Press UP or DownError Signals Optional Control SettingsLost Time Signal LOW Salt SignalSpecifications/Dimensions Sanitizing ProceduresAbout the water softener system Do not overtighten the cap Breaking a Salt BridgeNormal Operation, Control Displays Feature Optional Recharge ControlsFeature Memory Feature/Service Automatic Electronic DiagnosticsVisual Checks Service Electronic Demand Time Features and ServiceService Timer/Softener, Service Checkout Procedure Error Code DisplayedPosition Switch Operation Service Set Model F or H CodeIf the water softening system does not draw brine, check However, you must keep the tank supplied with salt Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System Checking the Salt Storage Level and RefillingNo soft water Before you call for service…Water softening system After installationNot using any salt Water feels slipperyBrown/yellow Brown/yellow colored Water after installationWhen power applied Salty tasting orGEAppliances.com Parts list GEAppliances.com General Electric Parts Catalog Parts catalogSupport Screen What Is Not Covered For The Period Of We Will ReplaceWarrantor General Electric Company. Louisville, KY For The Period We Will Replace GE Water Softening System Warranty. For Customers in CanadaPage Información de seguridad Instrucciones para la Advertencia No use con agua que AdvertenciaRecomendaciones importantes para la instalación Instrucciones de instalaciónAdvertencia No use con Desempacado e inspecciónPlanifique la instalación del Descalcificador Dónde instalar el DescalcificadorHerramientas y materiales necesarios para la instalación Principal Ilustración de instalación normalInstale LA Válvula DE Bypass Instrucciones de instalación paso por paso4A. Cómo Conectar UN Tubo DE Drenaje DE Válvula Rígida RegresivoInstale LAS Abrazaderas DE Tierra Agregue Agua Y SAL AL Tanque DE SalmueraConectar a LA Fuente Eléctrica Ajuste LA Hora DE Inicio Programación del controlAjuste LA Hora DEL DÍA DEL AguaDías Para Desocupar Ajuste EL Nivel DE SALSeñal DE Bajo Nivel DE SAL Señales DE ErrorAjustes opcionales de control Señal DE Hora PerdidaEspecificaciones/Dimensiones Advertencia Si usted drenaProcedimientos de desinfección Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Junta Tapón de flujo Cómo limpiar la ensambladura de la boquilla y el VenturiRecargue Esta Noche Operación normal, Pantalla de controlFunción Memoria Característica/Servicio Diagnosis electrónica automáticaInspecciones Visuales VisualizadoOperación del interruptor de posición Alarm alarma de bajo nivel de salServicio Diagnóstico electrónico iniciado manualmente Operación DE DiagnósticoPresione el botón Recharge recargo Servicio Configurar el código del modelo F o HEl botón Mode modo Servicio Inspección manual del avance de la recargaPrecaución Cuidado y limpieza del sistema de descalcificación de aguaLa válvula de bypass manual está en la posición de bypass Antes de llamar para solicitar servicio…No hay agua DescalcificadaResbalosa después de la Veces el aguaEstá dura El agua se sienteCristalería en los Descalcificación noEstá regenerando Agua turbia en laDays to Empty Notas Lista de partes GEAppliances.com Catálogo DE Partes DE General Electric Catálogo de partesCubierta DE LA Válvula Notas GEAppliances.com Garante General Electric Company. Louisville, KY Garantía GE para el Sistema de Descalcificación de AguaPor el período de Reemplazamos Lo que no está cubiertoPiezas y accesorios Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadasReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

GXSF39E, GXSF35E specifications

The GE GXSF35E and GXSF39E are sophisticated water filtration systems designed to meet the diverse needs of residential consumers. Offering reliable water purification solutions, these models efficiently remove impurities, ensuring clean and safe water for household use.

Both the GXSF35E and GXSF39E units feature advanced filtration technology, specifically designed to target a broad spectrum of contaminants, including chlorine, sediment, lead, and other harmful substances. The filtration process effectively enhances the taste and smell of drinking water, allowing families to enjoy fresh and clean water directly from their taps.

One of the standout features of these models is their high-capacity filtration capabilities. The GXSF35E boasts a 35,000-gallon capacity, making it suitable for medium to large households. Conversely, the GXSF39E, designed for larger families, offers an impressive 39,000-gallon capacity. This extended capacity ensures that users have access to purified water for an extended period, reducing the frequency of cartridge replacements and associated maintenance.

In terms of technical specifications, both models utilize a unique dual-stage filtration system. The first stage consists of a high-performance sediment filter that captures large particles and sediments, while the second stage employs an activated carbon filter that removes chemical contaminants and enhances taste. This two-tiered approach ensures comprehensive purification and longevity of the filter media.

Another major characteristic of the GXSF35E and GXSF39E is their user-friendly design. With features such as easy installation processes, intuitive control panels, and filter change indicators, these systems cater to users with varying levels of technical expertise. The compact design of the units allows for versatile installation options, whether in basements, under sinks, or in utility rooms.

Both models are also equipped with smart technology, enabling users to monitor filter life through mobile applications or digital displays. This connectivity feature ensures that homeowners are well-informed when it’s time to replace filters, enhancing the system's overall efficiency and effectiveness.

In conclusion, the GE GXSF35E and GXSF39E water filtration systems stand out in the market due to their efficient filtration technologies, high capacity, user-friendly features, and smart monitoring capabilities. They provide an excellent solution for families seeking safe and clean drinking water without the hassles associated with traditional filtration methods.