GE GXWH20F Attach Fittings to Water Line, Installing the Unit, Installing the Ground Wire

Page 4

STEP-BY-STEP INSTALLATION INSTRUCTIONS (cont.)

Attach Fittings to Water Line

 

Slip a compression nut onto each pipe.

1

 

Next, slip the brass ferrule onto each pipe.

2

 

D

Brass ferrule

Brass ferrule

Hex nut

Hex nut

Installing the Unit

1

Align filter assembly with pipe ends, making certain that the

incoming water supply is going into the filter opening marked

 

 

“IN”. It may be necessary to spread the pipe ends apart to

 

install filter assembly.

 

Using a 118″ wrench to hold the fitting in place, use a 114

2

wrench to tighten the nut. Repeat process for other fittings.

 

3

4

Hang mounting bracket with unit onto previously installed screws. Drive two screws to secure unit tightly to the wall if necessary.

Install a filter into the housing and tighten canister to seal (see Filter Cartridge Replacement section).

Installing the Ground Wire

NOTE: If your house plumbing is plastic, it would not be used as a grounding path, and this step should be skipped.

IMPORTANT: A copper or galvanized cold water pipe is often used to ground electrical outlets in the home. Grounding protects you from electrical shock. The water filter housing may have broken this ground path. To restore connection, install a 12″ long,

6-gauge copper wire across the filter, and tightly clamp using UL-approved 1/2″ –1″ bronze grounding clamps at both ends as shown. Zinc clamps should not be used on copper plumbing. For GXWH04F, wire and clamps may be purchased separately from your local hardware store, or are available by visiting our Website at ge.com, or from Parts and Accessories by calling 800.626.2002 (U.S.)or 800.663.6060 (Canada)—order part number WHKIT.

1

Clean copper pipe and ends of wire with emery paper. Bare

wire is recommended. If insulated wire is used, it should be

 

 

stripped 3/4″ at each end before cleaning with emery paper.

 

Attach bronze clamps to copper pipe. Tighten screws.

2

 

Attach wire to clamps as shown. Tighten screws.

3

Ground wire

Clamp

Final Check

1

2

3

Install filter, if not already done. (See Filter Cartridge Replacement section.)

Slowly turn on water supply.

Check entire system for leaks.

4

5

If leaking from fittings, shut off water pressure and tighten or reseal fittings. If leaking from the canister, tighten the canister with a wrench.

Open any downstream faucet and allow filter and housing to flush for 5 minutes.

Timer Installation and Application Instructions

Blue reset button

Timer cap

2 AAA batteries

Timer base

Timer seat

Head

Timer battery installation and change

Insert coin or screwdriver into the slot between timer cap and base. Gently pry them open and separate timer base from cap. Install or change 2 new AAA 1.5 volt batteries. After you have the batteries in place, line up the base and cap and snap them back together.

It is recommended to change the batteries at least every 2 filter changes, or when the blue LED light seems dim.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries.

Installation of timer

Hold the timer body in the center and gently push the timer to its seat at the top of the head or attach it in a remote location for easy viewing.

Timer reset and application

After new batteries are installed or filter is changed, push and hold the blue timer reset button (hold the reset button for approximately 5 seconds). Release the reset button after the light stops flashing. The timer has been reset. The light will flash again in 90 days to remind you that it is time to change the filter.

4

Image 4
Contents Filtration Housing Freezing. Water freezing in the housing will damage itPressure-reducing valve before the housing is installed HOT water 100˚F maxPerformance Data Sheet Replacement Filter CartridgesFilter Cartridge Replacement About the Filter CartridgeSTEP-BY-STEP Installation Instructions Installation OverviewInstall Fittings and Mounting Bracket Select LocationInstalling the Unit Installing the Ground WireTimer Installation and Application Instructions Timer battery installation and changeParts List Exclusion of Implied WARRANTIES-Your soleInstructions D’INSTALLATION LA Cartouche DE Filtration Étapes DE L’INSTALLATION Illustration de l’installationEmplacement d’installation Sectionnement de la canalisation d’eauInstallation des raccords sur la canalisation Installation du filtreInstallation du conducteur de liaison à la terre Installation de la minuterie et instructions d’applicationGaranties de commercialité et d’adéquation à un usage Liste DES PiècesCourte autorisée par la législation Page Instrucciones DE Instalacion Hoja de datos de desarrollo LOS Cartuchos DEL FiltroManija de control modelo GXWH20F OFF apagado Instrucciones DE Instalacion Paso a Paso Sumario de la instalaciónSeleccione la ubicación Corte de la línea de aguaConecte las uniones a la línea del agua Instalación de la unidadInstalación del cable de tierra Revisión finalLista DE Partes De ref Parte No Descriptión