Mounting Bracket to Cabinet Wall

The bracket can be used as a template for marking the location of the mounting screws. When determining the location of the bracket, make sure you leave 1 1/2″ to 2″ of free area under the sumps to allow for sump removal and enough space on either side to make the tubing connections.

7 9⁄16 ″

Mounting bracket

Tubing connector (inlet)

Sump

Filter I

1 1⁄2 ″ to 2″

Tubing

connector (outlet)

Mounting screws

Sump

Filter II

Tubing Connections – Push-In Style (Models GXSL03C [rev. 2] and GXSV10C)

1 Run the length of the 3⁄8″ tubing, connected to the bottom of the faucet, to the filter system outlet (illustration above). Allow enough slack in the tubing so that the unit can be easily removed.

2 Measure and cut the end of the tubing square using a sharp cutter or knife. Remove any burrs (illustration A).

3 Inspect the end of the tubing, about 1 inch, to be sure there are no imperfections. It may be necessary to cut the tubing again.

4 Mark the tubing for length of insertion. For 3/8″ OD tubing the insertion length should be approximately 3/4 of an inch. Tubing must be fully

inserted to avoid leaks.

5 DO NOT REMOVE GRAY COLLET. Push the tubing all the way into the fitting until it bottoms out. The insertion line should be hidden or barely visible (illustration B and C). Slightly pull on the tubing to verify engagement.

6 Repeat the procedure to connect the tubing between the filter system inlet and the water supply/saddle valve (illustration in the Installation Overview section).

7 To remove tubing (illustration D), depress and hold gray collet. Pull tubing to remove.

A	Cut tubing square

End of tubing round and smooth, with no cuts, nicks

or flat spots (approximately 1 inch)

B	Gray Collet
B	(DO NOT REMOVE)
	(DO NOT REMOVE)
	Insertion line
	Tubing
	3⁄4 ″		Tubing must
	3⁄4 ″		be fully inserted
			be fully inserted
	Insert		to avoid leaks.
C	Gray Collet
C	(DO NOT
	REMOVE)
	3	4"
	Insertion line

NOTE: Avoid installing the unit where the tubing is pulled at a sharp angle. This type of installation may cause the fittings to leak. If using tubing other than what is supplied, be sure it is high quality, exact size and roundness, and has a smooth surface.

Insert tubing

	Engagement
	3/4″ (3/8″ tubing)
D	Gray Collet
D
	Tubing

Depress gray collet and pull tubing

to remove.

GXSL03C, GXSV10C specifications

The GE GXSL03C and GXSV10C are two models in General Electric's range of water filtration systems, known for their innovative features and advanced technologies. Designed to provide clean and safe drinking water, these systems cater to a variety of needs, from residential households to more extensive applications.

The GE GXSL03C model is particularly notable for its compact design and efficiency. It incorporates a reverse osmosis filtration system, which is highly effective in removing impurities, harmful contaminants, and sediments from water. This model is equipped with a five-stage filtration process that includes pre-filters, post-filters, and a thin-film composite membrane, ensuring a thorough purification. It has a maximum flow rate that allows for convenient water delivery, making it suitable for daily use.

On the other hand, the GE GXSV10C boasts a higher capacity and is designed specifically for larger households or small businesses. This model also employs advanced filtration technology, including a multi-stage process that removes chlorine, lead, and other unwanted substances. A key feature of the GXSV10C is its built-in smart technology, which monitors the status of filters and indicates when replacements are due. This ensures optimal performance and convenience for users.

Both models highlight user-friendly designs, featuring easy-to-replace filters and straightforward installation processes. They come with detailed instructions and typically include necessary accessories for setup. Moreover, the compact nature of these systems allows for flexible installation options, including under-sink locations or in utility areas.

Durability is another strong characteristic of both the GXSL03C and GXSV10C. They are constructed from high-quality materials designed to withstand common wear and tear while maintaining performance over time. Additionally, GE backs these products with reliable customer service and support, ensuring users can easily access help when needed.

In summary, the GE GXSL03C and GXSV10C present powerful water purification solutions featuring advanced filtration technologies, user-friendly designs, and durability. Their focus on efficiency and performance makes them excellent choices for consumers seeking improved water quality in their homes or businesses. With these systems, customers can enjoy peace of mind knowing they are investing in reliable water filtration solutions.