Brother CS 100T operation manual GTrim the excess thread above the bobbin

Page 14

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

fWhile holding the end of the thread, gently press the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to wind the thread around the bobbin a few times. Then stop the machine.

Note

●If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine.

●When the foot controller is plugged in, the start/stop button cannot be used to start or stop sewing (only for models equipped with the start/stop button).

gTrim the excess thread above the bobbin.

CAUTION

●Make sure you follow the instructions carefully. If you do not cut the thread completely, and the bobbin is wound, when the thread runs low it may tangle around the bobbin and cause the needle to break.

hSlide the sewing speed controller to the right (to set the speed to fast). (For models equipped with the sewing speed controller.)

iPress the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to start.

jWhen the bobbin seems full and begins spinning slowly, take your foot off the foot

controller or press (start/stop button) (for models equipped with the start/stop button).

kCut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

lSlide the sewing speed controller back to its original position (for models equipped with the sewing speed controller).

Memo

●When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.

●The needle bar does not move when you slide the bobbin winding shaft to the right.

CAUTION

●Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

1 2

aWound evenly

bWound poorly

aSewing speed controller

12

Image 14

Contents

Computerized Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Accessories Optional accessoriesBSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionPass the thread around the pre-tension disk Threading the MachineWinding the bobbin ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Needle types and their uses Needle precautionsReplacing the Needle FabricsCorrect needle Checking the needleReplacing the needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Attaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder Remove the presser footGeneral sewing procedure SewingTurn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser footBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tightChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing stretch fabrics Using a free-arm styleSewing thin fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchBasic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle positionIf the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingBaste the fabric to be quilted Using the optional quilting guideQuilting DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogBar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching DTrim along the stitches FagotingScallop stitching Sew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathersUnfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Stitch Settings Utility stitchesRfc. Reinforcement Decorative Stitch Buttonhole Bar tack Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Thread ten LowerOr breaks Fabric isThere is a high Stitches areSkipped Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-3215