Brother CS 100T operation manual ESelect a stitch, With stitch Select stitch

Page 41

dPlacethe fabric.a button between the presser foot and

When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the button so that the needle goes into the two holes toward the rear of the sewing machine, and then sew them in the same way.

eSelect a stitch

. (With models not provided

with stitch

, select stitch .)

fAdjust the stitch width so that it is the same as the distance between the holes in the button.

gSet the stitch length to the shortest setting by pressing the stitch length adjustment key.

hTurn the handwheel toward you (counterclockwise) to check that the needle correctly goes into the two holes of the button.

Adjust the stitch width to the distance between the button holes.

3

CAUTION

When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break.

iStart sewing.

After sewing for about 10 seconds at low

speed, press (reverse/reinforcement stitch button) to sew reinforcement stitches.

jPull the upper thread at the end of the stitching to the wrong side of the fabric, and then tie it with the bobbin thread.

Use scissors to cut the upper thread and the bobbin thread at the beginning of the stitching.

kWhen you are finished attaching the button,

slide the feed dog position lever to (to the left as seen from the front of the machine) to raise the feed dogs.

39

Image 41
Contents Computerized Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only For safe operation For a longer service lifeContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Optional accessories AccessoriesPower supply precautions Using Your Sewing MachineBSet the main power switch to CTo turn off the machine, set the main power switch toChanging the needle stop position Foot controllerWinding the bobbin Threading the MachinePass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin CSlide the bobbin winder shaft to the right For models equipped with the fast bobbin winding systemActual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Right side see arrow b until the cover clicks into placeUpper threading Thread take-up lever Catch the thread on the hook as shown below DFully lower the needle threader leverLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Replacing the Needle Needle precautionsNeedle types and their uses FabricsReplacing the needle Checking the needleCorrect needle Incorrect needleInstalling the needle clamp Twin needle threading Sewing with a twin needleMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footSewing General sewing procedureSelecting stitching DIfwidth.necessary, adjust the stitch lengthTurn on the sewing machine CAttach the presser footBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Sewing reinforcement stitches Thread tensionCorrect tension Upper tension is too tightTrial sewing Useful Sewing TipsChanging the sewing direction Sewing curvesSewing thin fabrics Using a free-arm styleSewing stretch fabrics Slide the flat bed attachment to the left to release itAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesBasic Stitching When sewing is finished, cut the threadBasic stitching Changing the needle positionIf the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingIf the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics With stitch Select stitch ESelect a stitchRev. Reverse Zipper InsertionElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingPiecing Patchwork crazy quilt stitchingQuilting Using the optional quilting guideBaste the fabric to be quilted DSelect stitch , orGAfter sewing is finished, slide the feed dog Free-motion quiltingTriple stretch stitching Reinforcement StitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching DTrim along the stitches FagotingScallop stitching Shell tuck stitching SmockingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersUnfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Utility stitches Stitch SettingsRfc. Reinforcement Decorative Stitch Buttonhole Bar tack Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Or breaks LowerThread ten Fabric isSkipped Stitches areThere is a high Pitched noise While sewingOperation beep for models equipped with the operation beep Error MessagesNumerics Index30, 32 English 885-S33/S34/S36/S37 XC8835-3215

CS 100T specifications

The Brother CS 100T is a versatile and user-friendly sewing machine, designed to cater to both budding sewists and experienced crafters alike. With its lightweight build and robust features, the CS 100T has become a popular choice for those looking to explore their creative side, tackle household projects, or even dive into garment making.

One of the main features that sets the Brother CS 100T apart is its impressive selection of built-in stitches. The machine offers 100 stitch options, including decorative, utility, and quilting stitches. This variety allows users to experiment with different techniques and styles, ensuring that every project can be personalized to their liking. The easy-to-use stitch selector makes navigating through the options a breeze, making it ideal for all skill levels.

The CS 100T is equipped with an automatic needle threader, which takes the hassle out of threading the needle and saves valuable time. Additionally, the top drop-in bobbin system allows for easy bobbin changes, reducing downtime and keeping your sewing project flowing smoothly. This machine also includes a speed control feature, enabling users to adjust the sewing speed according to their comfort and skill level.

Another key technology incorporated in the Brother CS 100T is the built-in monogramming feature. With the ability to create customized letters and numbers, this machine allows users to personalize their projects, making it an excellent choice for gifts or special occasions. Furthermore, the machine comes with various presser feet, including a zipper foot and buttonhole foot, allowing for greater versatility in sewing techniques.

Its lightweight design, weighing in at just under ten pounds, makes the CS 100T highly portable, allowing users to easily transport it for sewing classes or crafting gatherings. The strong construction and durable materials ensure that it can withstand regular use while still producing high-quality results.

In terms of characteristics, the Brother CS 100T is designed for ease of use. The intuitive layout includes a bright LED light that illuminates the sewing area, providing better visibility during projects. The stitch length and width can be adjusted, giving users more control over their creations.

Overall, the Brother CS 100T is a feature-rich sewing machine that combines ease of use, versatility, and advanced technology. Whether you’re a beginner looking to learn the basics or an experienced sewist in need of a reliable machine, the CS 100T offers a wide range of capabilities to inspire creativity and enhance your sewing experience.