Brother CS 100T operation manual Right side see arrow b until the cover clicks into place

Page 17

the right side (see arrow b) until the cover clicks into place.

•Replace the cover so that the end of the thread comes out from the left side of the cover (as shown by the line in the diagram).

■For models equipped with the quick-set bobbin

aRaise the needle to its highest position by turning the handwheel toward you (counterclockwise) or press (needle position button) (for models equipped with the needle position button), and raise the presser foot lever.

bSlide the button and open the cover.

1 2

aCover

bSlide button

cPut the bobbin in, feed the end of the thread through the slit, and then pull the thread to cut it.

•Only use bobbins that were designed to be used with this machine.

CAUTION

●Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.

1

aCutter

•Make sure that the thread is correctly inserted through the tension-adjusting spring of the bobbin case. If it is not inserted, re- insert the thread.

1

1

aTension-adjusting spring

Memo

●The order that the bobbin thread should be passed through the bobbin case is indicated by marks around the bobbin case. Be sure to thread the machine as indicated.

dReplace the bobbin cover. Put the left tab in place (see arrow a), and then press lightly on the right side (see arrow b) until the cover clicks into place.

Memo

●You can begin sewing immediately without drawing up the bobbin thread. If you want to draw up the bobbin thread before you start to sew, follow to the procedure in “Drawing up the lower thread” (page 19).

15

Image 17

Contents

Computerized Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only For safe operation For a longer service lifeContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Optional accessories AccessoriesPower supply precautions Using Your Sewing MachineBSet the main power switch to CTo turn off the machine, set the main power switch toChanging the needle stop position Foot controller Winding the bobbin Threading the Machine Pass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin CSlide the bobbin winder shaft to the right For models equipped with the fast bobbin winding systemActual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Right side see arrow b until the cover clicks into placeUpper threading Thread take-up lever Catch the thread on the hook as shown below DFully lower the needle threader leverLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Replacing the Needle Needle precautionsNeedle types and their uses FabricsReplacing the needle Checking the needleCorrect needle Incorrect needleInstalling the needle clamp Twin needle threading Sewing with a twin needleMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footSewing General sewing procedureSelecting stitching DIfwidth.necessary, adjust the stitch lengthTurn on the sewing machine CAttach the presser footBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Sewing reinforcement stitches Thread tensionCorrect tension Upper tension is too tightTrial sewing Useful Sewing TipsChanging the sewing direction Sewing curvesSewing thin fabrics Using a free-arm styleSewing stretch fabrics Slide the flat bed attachment to the left to release itAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesBasic Stitching When sewing is finished, cut the threadBasic stitching Changing the needle positionIf the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingIf the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics With stitch Select stitch ESelect a stitchRev. Reverse Zipper InsertionElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingPiecing Patchwork crazy quilt stitchingQuilting Using the optional quilting guideBaste the fabric to be quilted DSelect stitch , orGAfter sewing is finished, slide the feed dog Free-motion quiltingTriple stretch stitching Reinforcement StitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching DTrim along the stitches FagotingScallop stitching Shell tuck stitching SmockingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersUnfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Utility stitches Stitch SettingsRfc. Reinforcement Decorative Stitch Buttonhole Bar tack Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Or breaks LowerThread ten Fabric isSkipped Stitches areThere is a high Pitched noise While sewingOperation beep for models equipped with the operation beep Error MessagesNumerics Index30, 32 English 885-S33/S34/S36/S37 XC8835-3215