Brother CS-770 operation manual Zipper Insertion, Rev. Reverse

Page 42

UTILITY STITCHES ——————————————————————————————————————————————————

ZIPPER INSERTION

You can use the zipper foot to sew different types of zippers, and can easily position it to the right or left side of the needle.

When sewing the right side of the zipper, attach the shank to the left pin of the zipper foot. When sewing the left side of the zipper, attach the shank to the right pin of the zipper foot.

Stitch Name

Straight stitch (center)

 

 

Presser Foot

 

Pattern No.

 

Pattern

 

 

 

 

70 stitches model

60 stitches model

50 stitches model

40 stitches model

 

 

I

01

01

01

01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stitch Width

Stitch Length

 

[mm (inch.)]

[mm (inch.)]

Application

 

 

 

 

 

 

 

 

 

Auto

Manual

Auto

Manual

Attaching zippers, basic

 

 

2.5

0.2–5.0

stitching, and sewing

(3/32)

(1/64–3/16)

gathers or pintucks, etc.

 

 

 

 

 

 

 

 

 

 

 

Twin Needle

Walking Foot

Reverse/ Reinforcement Stitching

Yes

**

Rev.

*

( J )

Yes

 

 

 

 

 

 

 

 

*Rev.: Reverse

**Do not use reverse stitching.

1 2

3

aZipper foot

bRight pin for sewing the left side of the zipper

cLeft pin for sewing the right side of the zipper

aSelect stitch .

bLower the presser foot lever and fix either the left or right pin of the zipper foot onto the shank.

cFold the edge of the material 2 cm (3/4 inch) and place the zipper under the folded section. Lower the needle into the notch located either on the left or right side of the zipper foot.

CAUTION

Turn the handwheel by hand to make sure the needle does not hit the presser foot before you start sewing. If you choose a different stitch, the needle will hit the presser foot and break the needle. You may also be injured.

dSew from the bottom of the zipper toward the top on both sides. The needle should be positioned on the zipper side of the foot for best results.

eTo sew the opposite side of the zipper, release the foot by pressing the button located at the back of the presser foot, fit the zipper foot on the other side of the zipper and continue sewing using the other side notch.

CAUTION

Make sure the needle does not hit the zipper during sewing. If the needle hits the zipper, the needle may break and you may be injured.

40

Image 42
Contents Computerized Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsNeedle and presser foot section Operation buttonsButtons provided on some models Operation panel Flat bed attachmentASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesBSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionPass the thread around the pre-tension disk Threading the MachineWinding the bobbin ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowDrawing up the lower thread For models equipped with the quick-set bobbinLightly hold the end of the upper thread Needle types and their uses Needle precautionsReplacing the Needle FabricsCorrect needle Checking the needleReplacing the needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the Presser Foot Replacing the presser footMark on the wheel points up. With models Attaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder Remove the presser footGeneral sewing procedure SewingTurn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser footStarting to sew On the wheel points up. With models equippedBRaise the presser foot lever Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tightChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing stretch fabrics Using a free-arm styleSewing thin fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchBasic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle positionBlind HEM Stitching BAttach blind hem foot R CSelect a stitchIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plate FPullpossible.down the buttonhole lever as far as Button sewing Sewing buttonholes on stretch fabricsCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingBaste the fabric to be quilted Using the optional quilting guideQuilting DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogBar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Fagoting Scallop stitchingDTrim along the stitches Sew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathersJoining Heirloom stitchingUnfold the fabric, and then iron the tucks down to one side Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Maintenance Cleaning the machine surfaceCleaning the bobbin case Remove the bobbin case Troubleshooting Thread ten LowerOr breaks Fabric isThere is a high Stitches areSkipped Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 Page English 885-S33/S34/S36/S37 XC8835-7219