Brother CS-770 Error Messages, Operation beep for models equipped with the operation beep

Page 64

APPENDIX —————————————————————————————————————————————————————

ERROR MESSAGES

If an operation is performed incorrectly before the sewing machine is set up, an error message appears on the operation panel. Follow the instructions indicated in the table.

If you press the stitch selection key or do the operation correctly while the error message is displayed, the message disappears.

Error Message

Probable Cause

Solution

 

 

 

 

The foot controller was pressed (or the start/stop but-

Lower the presser foot lever

 

ton was pressed if the foot controller is not con-

before continuing the opera-

 

nected) and the reverse/reinforcement stitch button

 

tion.

 

was pressed while the presser foot is raised.

 

 

 

 

 

 

A stitch other than the buttonhole or bar tack stitch

 

 

was selected and the foot controller was pressed (or

Raise the buttonhole lever

 

the start/stop button was pressed if the foot controller

before continuing the opera-

 

is not connected) while the buttonhole lever is low-

tion.

 

ered.

 

 

The buttonhole or bar tack stitch was selected and

Lower the buttonhole lever

 

the foot controller was pressed (or the start/stop but-

 

before continuing the opera-

 

ton was pressed if the foot controller is not con-

 

tion.

 

nected) while the buttonhole lever is raised.

 

 

 

 

 

 

The reverse/reinforcement stitch button or needle

Move the bobbin winder

 

position button was pressed while the bobbin winder

shaft to the left before con-

 

shaft is moved to the right.

tinuing the operation.

 

 

Disconnect the foot control-

 

The start/stop button was pressed while the foot con-

ler, and then press the start/

 

troller was connected.

stop button. Otherwise,

 

operate the machine by

 

 

 

 

using the foot controller.

 

 

 

 

 

Remove the tangled thread

 

The motor locked up because the thread is tangled.

before continuing the opera-

 

 

tion.

 

 

 

Note

●If error message “F1” through “F8” appears in the LCD while the sewing machine is being used, the machine may be malfunctioning. Contact your nearest authorized service center.

Operation beep (for models equipped with the operation beep)

Each time a key is pressed you will hear one beep. If a non-functioning key is pressed or an incorrect operation is performed you will hear two or four beeps (only for models equipped with the operation beep).

■If a key is pressed (correct operation) One beep sounds.

■If an incorrect operation is performed or a non-functioning key is pressed Two or four beeps sound.

■If the machine locks up, for example, because the thread is tangled

The sewing machine beeps for four seconds and the machine automatically stops. Be sure to check for the cause of the error, and correct it before continuing to sew.

62

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Computerized Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsOperation buttons Needle and presser foot sectionButtons provided on some models Flat bed attachment Operation panelASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesUsing Your Sewing Machine Power supply precautionsBSet the main power switch to CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionThreading the Machine Winding the bobbinPass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowFor models equipped with the quick-set bobbin Drawing up the lower threadLightly hold the end of the upper thread Needle precautions Replacing the NeedleNeedle types and their uses FabricsChecking the needle Replacing the needleCorrect needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the presser foot Replacing the Presser FootMark on the wheel points up. With models Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footGeneral sewing procedure SewingDIfwidth.necessary, adjust the stitch length Selecting stitchingTurn on the sewing machine CAttach the presser footOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Thread tension Sewing reinforcement stitchesCorrect tension Upper tension is too tightUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesUsing a free-arm style Sewing thin fabricsSewing stretch fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchWhen sewing is finished, cut the thread Basic StitchingBasic stitching Changing the needle positionBAttach blind hem foot R CSelect a stitch Blind HEM StitchingIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics Button sewingCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingUsing the optional quilting guide QuiltingBaste the fabric to be quilted DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogReinforcement Stitching Triple stretch stitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Scallop stitching FagotingDTrim along the stitches Smocking Shell tuck stitchingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersHeirloom stitching JoiningUnfold the fabric, and then iron the tucks down to one side Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the machine surface MaintenanceCleaning the bobbin case Remove the bobbin case Troubleshooting Lower Or breaksThread ten Fabric isStitches are SkippedThere is a high Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 Page English 885-S33/S34/S36/S37 XC8835-7219

CS-770 specifications

The Brother CS-770 is a versatile sewing machine that combines advanced technology with user-friendly features, making it an ideal choice for both beginners and seasoned sewists. This model stands out with its robust construction and sleek design, ensuring durability and performance.

One of the key features of the Brother CS-770 is its impressive range of stitch options. The machine boasts 140 built-in stitches, including utility, decorative, and heirloom stitches. This extensive selection offers users the flexibility to create a variety of projects, from simple hems to intricate quilt patterns. The stitches are easily accessible through an intuitive LCD screen, which displays the selected stitch and allows for quick adjustments.

Another highlight of the CS-770 is its automatic needle threader. This convenient technology eliminates the frustration often associated with threading the needle, allowing sewists to focus on their projects instead. Additionally, the drop-in bobbin system simplifies the process of loading the bobbin, reducing downtime and enhancing efficiency.

The machine features a 7-point feed dog system, ensuring smooth and even fabric feeding, whether working with delicate fabrics or heavier materials. This powerful feed mechanism is complemented by a range of presser feet, including a walking foot and a quilting foot, enhancing the machine’s versatility for different sewing tasks.

For those interested in quilting, the Brother CS-770 includes a wide table attachment, providing extra support for larger projects. This feature is particularly beneficial for quilters, allowing them to maneuver their work with ease. The machine also supports free-motion quilting, giving users the freedom to create unique designs.

Other notable characteristics of the Brother CS-770 include adjustable sewing speed, allowing users to set the pace according to their comfort level. The machine also has an auto-declutch bobbin winder, ensuring even and consistent bobbin winding. With built-in storage for accessories and a hard case for protection, this sewing machine is designed for ease of use and convenience.

Overall, the Brother CS-770 integrates innovative sewing technologies with practical features, making it a reliable choice for a wide range of sewing projects. Whether you are a hobbyist looking to dive into new techniques or an experienced sewist seeking a dependable machine, the CS-770 is equipped to meet various sewing needs. Its balance of functionality and user-friendly design makes it a standout model in Brother’s acclaimed lineup of sewing machines.
Top Page Image Contents