Brother PC-2800 operation manual Buttonhole Stitching

Page 45

BUTTONHOLE STITCHING

A

 

 

 

 

 

11

12

13

14

15

11: Rounded buttonhole on light to medium weight fabric

 

 

 

 

 

*2

 

 

 

 

 

12: Squared buttonhole for light and medium weight fab-

 

 

 

 

 

rics *1

13:Squared heavy-duty buttonhole with reinforced bar tacks in medium to heavyweight fabrics *3

14:Stretch buttonhole with reinforced bar tacks in light to medium weight stretch fabrics, medium to heavyweight tightly woven fabrics, heavyweight fabrics with stretch fabrics *2

15:Keyhole buttonhole in heavyweight fabrics for larger flat buttons *2

*1 For use on low stress or decorative applications

*2 For use on average stress applications

*3 For use on high stress or utility applications

Note

Before sewing a buttonhole on your project, practice on a scrap piece of the same type of fabric.

1. Mark the position and length of the buttonhole on the fabric.

*The maximum buttonhole length is 30 mm (1-3/16'') (diameter + thickness of the button)

 

13

 

14

*

Thick thread (#30) cannot be used with the “

” and “

”

 

buttonhole styles.

 

 

2.

Attach buttonhole foot “A”. Pull out the button holder plate on

5

the presser foot, and insert the button that will be put through

the buttonhole, then tighten the button holder plate around the

 

6

button.

 

 

*The size of the buttonhole is decided by the button holder plate holding the button.

1Button holder plate

3.Align the presser foot with the mark on the fabric, and lower the presser foot lever.

 

1

Mark on the fabric

 

1

2

Mark on the presser foot

 

 

5

 

 

 

6

 

 

 

CAUTION

 

 

•

Slide the outside frame of the buttonhole foot

 

 

 

backward as far as possible as shown in the il-

 

A

 

lustration, making sure that there is no gap be-

 

 

hind the part of the foot marked “A”. If the button-

A

 

 

hole foot is not slid back as far as possible, the

 

 

buttonhole will not be sewn with the correct size.

 

 

•

Pass the thread underneath the presser foot.

 

CONTENTS

BEFORE USE

SEWING

PATTERNS UTILITY STITCHES MAINTENANCESEWING CHART(PROGRAMMED IN MACHINE)

42

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta Cyprus only Congratulations on Choosing OUR Machine Contents Maintenance Part Names Before USEPower cord Main power switchPresser foot symbol Foot controller jackStandard Accessories Optional Accessories Operation Panel Operation Buttons Using the operation buttonsPower Supply Winding the bobbin and setting the bobbin thread Bobbin Winding / Bobbin Thread Setting324,9 Spool cap Spool pinSpring on the shaft Groove of the bobbin Setting the bobbin Bobbin cover Bobbin cover release buttonBuilt-in thread cutter Upper threading shutter Upper ThreadingThread take-up lever Needle clamp thread guideNeedle threader lever Guide Large hook Second set of hooks Third hook Extra spool pin Using the extra spool pin and the netNet Net Thread spool Spool pin Spool capSTART/STOP button Starting and Stopping SewingFoot controller Foot controller Foot controller jackSelecting a Stitch Pattern Lit LED lamp shows the selection Stitch pattern switch keyNot adjustable Correct upper thread tension Thread TensionLoosening the upper thread tension Wrong side Right side Upper thread Bobbin threadTightening the upper thread tension Removing the presser foot holder while cleaning, etc Presser FootChanging the presser foot Needle clamp screw Operating lever Walking foot shank Attaching the Optional Walking FootFeed DOG Needle stopper Hole for setting needle Flat side of needle Installing the needle securelyNeedle Checking the needleFABRIC/THREAD/NEEDLE Combination Chart About the NeedleFabric Thread Size of needle Type Trial Sewing Sewing using a utility stitchThread cutter You can begin sewing without drawing up the bobbin threadCanceling the needle stop down position setting Setting the Needle Stop Down PositionWhen the needle stop position switch keys LED lamp is Lit, the needle stop position is set to the down positionAdjusting the stitch length Adjusting the stitch widthStitch Width and Length Up Wider Down NarrowerSewing corners Useful SkillsSewing curves Sewing a curve with a straight stitchSewing heavyweight fabrics Sewing lightweight fabricsFabric Thick paper Using the needle plate Free-arm sewing15 mm 9/16 To 4 reverse stitches Straight StitchesSewing stretch fabrics Changing the stitch lengthBasting Appliqué using a zigzag stitch Overcasting using a zigzag stitchSewing curves using a zigzag stitch Zigzag StitchesSewing using stitch 7 or Sewing using stitch 4 orOvercasting Stitches Needle clamp screw Operating lever Overcasting When Using the Optional Side Cutter20 mm 3/4 Guide plate lower knife Presser footSeam margin Blind HEM Stitching Adjusting the needle drop point Buttonhole Stitching Eyelet punch Basting pin Metal bracketButtonhole sewing order Sewing stretch fabrics 13Reinforcement stitch 10 mm 3/8 Changing the stitch width Size of eyelet actual size Eyelet StitchFor sewing eyelets on belts, etc Large Medium SmallZipper Insertion Make sure you sew using the middle needle positionCentered zipper For attaching zippersNeedle will strike the presser foot, causing When using zipper foot I, make sure the straightFabric End of zipper openingBasting stitches To 10 mm 1/4 to 3/8 Reverse stitches 50 mm Right Left Needle drop positionDart Seam Gathering Upper thread Bobbin thread About 50 mmSeam line 10 to 15 mm 3/8 to 9/16 About 50 mm Shuttle Pulling up the bobbin threadFor decorating blouses, etc PintuckFor reinforcing seams and neatly finishing edges Flat Fell SeamAbout 12 mm 1/2 Wrong side of fabric Finish line Wrong side of fabricFinished flat fell seam Sewing sharp curves AppliquésAppliqué Fabric glue Appliqué materialScallop Stitch EtcRight side of fabric Beforeuse Smocking Stitch For making decorative stitchingAbout 10 mm 3/8 Fagoting For fagoting, decorating, etcMm 3/16 Paper Basting stitches Decorative Stitching Decorative stitchingChanging the size of a decorative stitch Hemstitching Hemstitch Heirloom StitchRative stitching on shirtfronts Lamp is turned off Lamp is litIllustration of finished product Twin Needle Decorative stitches where the zigzag width can be changedManually StopperTypes of thread Stitch lengthSewing attractive finishes SewingStabilizer Thin paperCleaning the operation panel Cleaning the MachineCleaning the machine casing Cleaning the race and shuttleRace Same position as when you removed the raceDo not oil the shuttle or the race Brush Check that the notch on the shuttle isScrew Light cover Changing the Light BulbTrouble with threads and stitches Trouble ShootingMechanical trouble AlarmSewing Chart Programmed Machine Decorative Utility stitches Decorative stitches Patterns Programmed in MachinePage Page Page English 194953-011

PC-2800 specifications

The Brother PC-2800 is a versatile and compact typewriter designed for both home and office use. With a focus on convenience and user-friendliness, it offers a range of features that cater to the needs of modern typists. One of its standout characteristics is its built-in printer, which allows users to produce high-quality printed documents without the need for a separate printer.

One of the main features of the PC-2800 is its auto-correction technology. This innovative feature helps prevent typographical errors by automatically correcting common mistakes as you type, saving time and ensuring that the final output is polished. Additionally, this device offers a variety of fonts and styles to choose from, enabling users to customize their documents to better fit their personal or professional needs.

Another notable aspect of the Brother PC-2800 is its memory capacity. With the ability to store multiple documents, it allows users to easily switch between projects without the hassle of retyping. This feature is particularly useful for students, writers, and anyone who frequently works on various documents simultaneously. The typewriter’s LCD display provides a clear view of typed text, making it easy to follow along as you compose your work.

The PC-2800 utilizes thermal printing technology, which ensures that documents are produced with crisp and clear text. This form of printing is not only efficient but also quiet, making it an ideal choice for shared work environments. The Brother PC-2800 is also equipped with a range of connectivity options, allowing users to easily link the device to computers or other devices for seamless printing.

In terms of design, the Brother PC-2800 is compact and lightweight, making it easily portable. This design is perfect for those who may need to take their typewriter on the go, whether for meetings, classes, or simply to work in different locations. The user-friendly interface and intuitive controls make it accessible for individuals of varying skill levels, from novices to experienced typists.

In summary, the Brother PC-2800 is a reliable and multifunctional typewriter that merges traditional typing with modern technology. Its auto-correction feature, generous memory capacity, thermal printing technology, and user-friendly design make it an excellent choice for anyone in need of a durable and efficient typing solution. Whether for personal use, academic purposes, or professional environments, the PC-2800 stands out as an impressive tool for document creation.
Top Page Image Contents