Brother 885-V60 appendix For a longer service life

Page 4

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

4 Always keep your work area clear:

•Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot control free from the build up of lint, dust, and loose cloth.

•Do not store objects on the foot controller.

•Do not use extension cords. Plug the machine directly into the electrical outlet.

•Never drop or insert any object into any opening.

•Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

•Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or garment being sewn may ignite, resulting in fire or an electric shock.

•Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine may fall, resulting in injuries.

5 Special care is required when sewing:

•Always pay close attention to the needle. Do not use bent or damaged needles.

•Keep fingers away from all moving parts. Special care is required around the machine needle.

•Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.

•Do not use a damaged or incorrect needle plate, as it could cause the needle to break.

•Do not push or pull the fabric when sewing, and follow careful instruction when freehand stitching so that you do not deflect the needle and cause it to break.

6 This machine is not a toy:

•Your close attention is necessary when the machine is used by or near children.

•The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of. Never allow children to play with the bag due to the danger of suffocation.

•Do not use outdoors.

7 For a longer service life:

•When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects.

•Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used.

•Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct installation.

2

Page 3 Page 5
Image 4
Page 3 Page 5
Contents
Sewing Basics Utility Stitches Appendix Page Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta Cyprus only Contents Utility Stitches Included accessories AccessoriesAbout zigzag foot J Optional accessories Accessory compartmentNames of Machine Parts and Their Functions Main partsOperation buttons Needle and presser foot sectionButtons provided on some models Operation panel Spool pinShown.1 BPushplace.the spool pin down until it locks intoPower supply precautions Using Your Sewing MachinePower supply Foot controller Changing the needle stop positionAright to select the desired sewing speed Side of stitch selection keyWinding the bobbin Threading the MachineBRemove the spool cap DSlide the spool cap onto the spool pin Make sure that the thread passes under the pretension disk KTrim the excess thread above the bobbinFor models equipped with the fast bobbin winding system Thread is cut to a suitable length Lower threading Actual size 11.5mm 7/16 inch This modelFor models equipped with the quick-set bobbin Slit Cutter Cut the thread with the cutter Upper threading Remove the spool cap GSlide the spool cap onto the spool pinThread take-up lever Needle bar thread guide DFully lower the needle threader lever Catch the thread on the hook as shown belowLightly hold the end of the upper thread Drawing up the lower threadBobbin cover should still be removed Replacing the Needle Needle precautionsNeedle types and their uses Checking the needle Replacing the needleInstall the twin needle in the same way CLower the presser foot leverInstallthread.the thread spool and thread the upper Sewing with the twin needleThread the upper thread for the left needle For details, refer to steps a through l of Upper threadingFor details, refer to step a through l of Upper threading HAttach zigzag foot JModels equipped with a needle threader Turn on the sewing machine Select a stitchReplacing the Presser Foot Replacing the presser footReplace the presser foot as described below Mark on the wheel points up. With modelsRemove the presser foot Removing the presser foot holderFor details, refer to Replacing the presser foot Page Follow the basic procedures below to sew General sewing procedureSewing DIfwidth.necessary, adjust the stitch length Selecting stitchingPress the + or side of to increase or On the left changes the digit on the leftAdjusting the stitch length and width Right of in the LCDOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Sewing reinforcement stitches Raise the presser foot leverEach other Thread tension Correct tensionUpper tension is too tight Upper tension is too looseUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesSewing hook-and-loop Fastener Presser foot remains level, allowing the fabric to be fedSewing thin fabrics Sewing stretch fabricsStitching cylindrical pieces Slide the flat bed attachment to the left to release itUsing zigzag foot Overcasting StitchesAttach zigzag foot J Select stitch , or CSew with the edge of the fabricUsing overcasting foot Attach overcasting foot G Select stitch orWhen sewing is finished, cut the thread Basic StitchingBasic stitching For details, refer to Starting to sewBlind HEM Stitching Reverse the skirt or pantsFold back the fabric inside along the basting Thick fabric Normal fabric Stitch widthIf the needle does not catch the hem fold Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingAuto Rfc. Automatic Reinforcement **Rfc. Reinforcement Size of the buttonhole is set Once sewing is completed, Raiseposition.the buttonhole lever to its originalSewing buttonholes on stretch fabrics Trim off any excess of the gimp threadButton sewing DPlacethe fabric.a button between the presser footESelect a stitch With stitch Select stitchAfter sewing for about 10 seconds at low Normally, the feed dog position lever is Positioned atRev. Reverse Do not use reverse stitching Zipper InsertionRefer to Basic stitching on FSelect stitch Sew the stitching in order, from a to cSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching BAttach zigzag foot J CSelect stitchUtility Stitches APPLIQUÉ, Patchwork and Quilt Stitching PiecingAppliqués Patchwork crazy quilt stitchingPiecing Remove the basting, if necessaryQuilting For a seam allowance on the left sideDSelect stitch SewingUsing the optional quilting guide Free-motion quilting† Walking foot † Presser foot holder ARemoveholder. the presser foot and the presser footSlide the feed dog position lever, located at Reinforcement Stitching Triple stretch stitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Fagoting Scallop stitching SmockingDTrim along the stitches CSew parallel stitching at intervals of 10 mm 3/8 inchShell tuck stitching JoiningFold the fabric along the bias BAttach zigzag foot J Unfold the fabric, and then iron the tucks down to one sideHeirloom stitching Stitch Settings Utility stitchesPattern No Decorative Stitch Buttonhole Bar tack For decoration, etc For decoration, etc Yes Maintenance Cleaning the machine surfaceCleaning the bobbin case Remove the bobbin caseAlign the U and marks Needle plate cover Frequent troubleshooting topics TroubleshootingUpper thread tightened up Symptom For details, refer to Cleaning the bobbin case onTangled thread on wrong side of fabric Cause Incorrect upper threadingHFeed the upper thread as shown in the illustration below Thread take-up lever Incorrect thread tension DRemoveholder. the presser foot and presser foot Fabric is caught in the machine and cannot be removedIf threads remain in the bobbin case, remove them Be careful not to drop the removed screws in the machine Memo Do not yet install the presser foot and thread Checking machine operationsTurn on the machine Select middle needle position stitch Correctly thread the machineList of symptoms While sewing Machine doesNot work Fabric being Sewn withUpper Thread breaksLower Or breaksStitches are SkippedThere is a high Pitched noise While sewingAfter sewing Thread hasTightened up ThreadError Messages Operation beep for models equipped with the operation beepIndex Numerics42 , 45 English 885-V60/ V61 XE6528-1011
Top Page Image Contents