Brother 885-V60 appendix Checking the needle, Replacing the needle

Page 31

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

■Ball point needle

Use the ball point needle when sewing on stretch fabrics or fabrics where skipped stitches easily occur.

Use the ball point needle for best results when sewing patterns using monogramming foot “N”. The factory recommended needle is “HG-4BR” (Organ). Schmetz needles “JERSEY BALL POINT” 130/705H SUK 90/14 may be used as a substitute.

■Transparent nylon thread

Use a 90/14 to 100/16 needle, regardless of the fabric or thread.

CAUTION

●The appropriate fabric, thread and needle combinations are shown in the table on the previous page. If the combination of the fabric, thread and needle is not correct, particularly when sewing thick fabrics (such as denim) with thin needles (such as 65/9 to 75/11), the needle may bend or break. In addition, the stitching may be uneven or puckered or there may be skipped stitches.

Checking the needle

Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated.

Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even.

1

2

aFlat side

bNeedle type marking

■Correct needle

1

■Incorrect needle

If the distance between the needle and the flat surface is not even, the needle is bent. Do not use a bent needle.

1

1

aFlat surface

Replacing the needle

Replace the needle as described below. Use the disc-shaped screwdriver and a needle that has been determined to be straight according to the instructions in “Checking the needle”.

aRaise the needle by turning the handwheel toward you (counterclockwise) so that the

mark on the wheel points up. (With models

equipped with (needle position button), raise the needle by pressing once or twice.)

or

a Mark

b Needle position button

bTurn off the sewing machine.

CAUTION

●Before replacing the needle, be sure to turn off the sewing machine, otherwise injuries may occur if the foot controller or the start/ stop button is accidentally pressed and the machine starts sewing.

aFlat surface

29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Sewing Basics Utility Stitches Appendix Page Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta Cyprus only Contents Utility Stitches Included accessories AccessoriesAbout zigzag foot J Accessory compartment Optional accessoriesMain parts Names of Machine Parts and Their FunctionsOperation buttons Needle and presser foot sectionButtons provided on some models Spool pin Operation panelBPushplace.the spool pin down until it locks into Shown.1Power supply precautions Using Your Sewing MachinePower supply Side of stitch selection key Foot controllerChanging the needle stop position Aright to select the desired sewing speedWinding the bobbin Threading the MachineBRemove the spool cap DSlide the spool cap onto the spool pin KTrim the excess thread above the bobbin Make sure that the thread passes under the pretension diskFor models equipped with the fast bobbin winding system Thread is cut to a suitable length Actual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Slit Cutter Cut the thread with the cutter Upper threading GSlide the spool cap onto the spool pin Remove the spool capThread take-up lever Needle bar thread guide Catch the thread on the hook as shown below DFully lower the needle threader leverLightly hold the end of the upper thread Drawing up the lower threadBobbin cover should still be removed Replacing the Needle Needle precautionsNeedle types and their uses Replacing the needle Checking the needleCLower the presser foot lever Install the twin needle in the same wayFor details, refer to steps a through l of Upper threading Installthread.the thread spool and thread the upperSewing with the twin needle Thread the upper thread for the left needleTurn on the sewing machine Select a stitch For details, refer to step a through l of Upper threadingHAttach zigzag foot J Models equipped with a needle threaderMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Replace the presser foot as described belowRemove the presser foot Removing the presser foot holderFor details, refer to Replacing the presser foot Page Follow the basic procedures below to sew General sewing procedureSewing On the left changes the digit on the left DIfwidth.necessary, adjust the stitch lengthSelecting stitching Press the + or side of to increase orRight of in the LCD Adjusting the stitch length and widthOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Sewing reinforcement stitches Raise the presser foot leverEach other Upper tension is too loose Thread tensionCorrect tension Upper tension is too tightSewing curves Useful Sewing TipsTrial sewing Changing the sewing directionPresser foot remains level, allowing the fabric to be fed Sewing hook-and-loop FastenerSlide the flat bed attachment to the left to release it Sewing thin fabricsSewing stretch fabrics Stitching cylindrical piecesCSew with the edge of the fabric Using zigzag footOvercasting Stitches Attach zigzag foot J Select stitch , orAttach overcasting foot G Select stitch or Using overcasting footFor details, refer to Starting to sew When sewing is finished, cut the threadBasic Stitching Basic stitchingReverse the skirt or pants Blind HEM StitchingFold back the fabric inside along the basting Thick fabric Normal fabric Stitch widthIf the needle does not catch the hem fold Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingAuto Rfc. Automatic Reinforcement **Rfc. Reinforcement Size of the buttonhole is set Raiseposition.the buttonhole lever to its original Once sewing is completed,Trim off any excess of the gimp thread Sewing buttonholes on stretch fabricsWith stitch Select stitch Button sewingDPlacethe fabric.a button between the presser foot ESelect a stitchNormally, the feed dog position lever is Positioned at After sewing for about 10 seconds at lowRev. Reverse Do not use reverse stitching Zipper InsertionRefer to Basic stitching on Sew the stitching in order, from a to c FSelect stitchBAttach zigzag foot J CSelect stitch Sewing Stretch Fabrics and Elastic TapeStretch stitching Elastic attachingUtility Stitches Piecing APPLIQUÉ, Patchwork and Quilt StitchingRemove the basting, if necessary AppliquésPatchwork crazy quilt stitching PiecingSewing QuiltingFor a seam allowance on the left side DSelect stitchARemoveholder. the presser foot and the presser foot Using the optional quilting guideFree-motion quilting † Walking foot † Presser foot holderSlide the feed dog position lever, located at Attach zigzag foot J Select stitch Start sewing Reinforcement StitchingTriple stretch stitching Bar tack stitchingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching Fagoting CSew parallel stitching at intervals of 10 mm 3/8 inch Scallop stitchingSmocking DTrim along the stitchesUnfold the fabric, and then iron the tucks down to one side Shell tuck stitchingJoining Fold the fabric along the bias BAttach zigzag foot JHeirloom stitching Utility stitches Stitch SettingsPattern No Decorative Stitch Buttonhole Bar tack For decoration, etc For decoration, etc Yes Remove the bobbin case MaintenanceCleaning the machine surface Cleaning the bobbin caseAlign the U and marks Needle plate cover Frequent troubleshooting topics TroubleshootingUpper thread tightened up Cause Incorrect upper threading SymptomFor details, refer to Cleaning the bobbin case on Tangled thread on wrong side of fabricHFeed the upper thread as shown in the illustration below Thread take-up lever Incorrect thread tension DRemoveholder. the presser foot and presser foot Fabric is caught in the machine and cannot be removedIf threads remain in the bobbin case, remove them Be careful not to drop the removed screws in the machine Memo Correctly thread the machine Do not yet install the presser foot and threadChecking machine operations Turn on the machine Select middle needle position stitchList of symptoms Fabric being Sewn with While sewingMachine does Not workOr breaks UpperThread breaks LowerPitched noise While sewing Stitches areSkipped There is a highThread After sewingThread has Tightened upOperation beep for models equipped with the operation beep Error MessagesNumerics Index42 , 45 English 885-V60/ V61 XE6528-1011

885-V60 specifications

The Brother 885-V60 is a versatile sewing machine that caters to both novice and experienced sewers alike. With its myriad of features and advanced technologies, it stands out as a reliable tool for creating a wide variety of projects, from basic mending to intricate quilting.

One of the main features of the Brother 885-V60 is its 60 built-in sewing stitches, which include utility stitches, decorative stitches, and auto-size buttonhole options. This selection allows users to explore their creativity and tackle diverse sewing tasks with ease. The machine also offers a one-step buttonhole function, making it simple to create perfectly sized buttonholes in a matter of seconds.

The Brother 885-V60 boasts a generous sewing area, equipped with a large extension table that provides ample space for handling larger projects like quilts. This extended work surface enhances stability and support, ensuring that even extensive pieces can be managed comfortably. The adjustable stitch width and length further allow for customization of stitches, catering to individual preferences for each project.

Another highlight of the Brother 885-V60 is its automatic needle threader, which simplifies the threading process and reduces eye strain, particularly for those who may struggle with manual threading. The machine also features a jam-resistant drop-in bobbin system, making it quick and straightforward to replace the bobbin without any complications.

The LED lighting built into the Brother 885-V60 illuminates the workspace, ensuring visibility while working on intricate designs, even in low-light conditions. This feature is invaluable for detailed projects where precision is crucial.

In terms of technology, the Brother 885-V60 includes a variety of presser feet, allowing users to switch between functions easily. The machine supports various feet such as the zipper foot, walking foot, and quilting foot, providing flexibility and enhancing the sewing experience.

Additionally, the integrated speed control feature offers users the ability to adjust the sewing speed according to their comfort level, making it easier for beginners to build confidence or for seasoned sewers to work on complex projects efficiently.

Durable and built to last, the Brother 885-V60 is an excellent investment for anyone looking to enhance their sewing capabilities. With its combination of user-friendly features, advanced technology, and robust performance, this sewing machine is poised to meet the demands of a wide range of sewing enthusiasts.
Top Page Image Contents