Kenmore 625.39376 warranty Drain ALL Water from Softener, Protect the Water Softener from Freezing

Page 31

Care Of Your Water Softener

PROTECT THE WATER SOFTENER FROM FREEZING

If the softener is installed where it could freeze (sum- mer cabin, lake home, etc.), you must drain all water from it to stop possible freeze damage. To drain the sof- tener:

1.Close the shut-off valve on the house main water pipe, near the water meter or pressure tank.

2.Open a faucet in the soft water pipes to vent pres- sure in the softener.

3.Move the stem in a single bypass valve to bypass. Close the inlet and outlet valve in a 3 valve bypass system, and open the bypass valve. If you want water in the house pipes again, reopen the shut-off valve on the main water pipe.

4.Unplug the transformer at the wall outlet. Remove the salt hole cover and the main cover. Take off both drain hoses.

5.Carefully remove the large holding clips at the soften- er inlet and outlet. Separate the softener from the plastic installation adaptors, or from the bypass valve.

6.Remove the brinewell cover and disconnect the brine valve tubing at the nozzle and venturi assembly. Lift the brine valve out of the brinewell. Tip the brine valve upside down to drain water.

7.Lay a piece of 2 inch thick board near the floor drain. Move the softener close to the drain. SLOWLY and CAREFULLY, tip it over until the rim rests on the wood block with the inlet and outlet over the drain.

Do not allow the softener’s weight to rest on the inlet and outlet fittings or they will break.

8.Tip the bottom of the softener up a few inches and hold until all water has drained. Leave the softener laying like this until you are ready to use it. Plug the inlet and outlet with rags to keep dirt, bugs, etc. out.

DRAIN ALL WATER FROM SOFTENER

Floor Drain

Wood Block

FIG. 56

Questions? Call The Kenmore Water Line 1-800-426-9345

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Save this Manual Repair or Parts ? Call toll freeDisclaimer of implied warranties limitation of remedies ONE Year Limited Warranty on Water SoftenerThree Year Limited Warranty on Electronic Parts TEN Year Limited Warranty Against LeaksFacts and Figures to Keep Table of ContentsSafety Guides Inspect Shipment Unpack and Check Your CartonParts Descriptions Small PartsTools Needed Plan Your InstallationProper Order to Install Water Treating Equipment Plan Your InstallationSoft, Hot Where to Install the Water SoftenerDraw in Your Pipes and Fittings Suggested Slab Foundation InstallationPIPE, FITTINGS, Other Materials Needed OUTBefore Installing Checks & Tests Read Before Beginning InstallationAssemble Drain Port Elbow Inlet and Outlet Threaded Adaptors Install Plastic Bypass ValveAssemble Inlet Outlet ADAPTORS, or Plastic Bypass Valve Bypass ValveValve Bypass Install 3-Valve BypassInstalling Holding Clips Installing 3 Valve Bypass and PipesPosition Softener Into Place Locate Water Softener and Connect PipesMove Softener Into Place Typical Soldering ConnectionsConnect the Valve Drain Hose Connect Valve and Salt Tank DrainsConnect Salt Tank Overflow Tubing Leak Test Leak TestHouse Main Water Shutoff Valves Single BypassCold Water Pipe Grounding Water Meter Jumper WireConnecting Transformer Electrical RequirementsProgram the Timer Install Covers and Restart Water HeaterProgram The Timer Install CoversSET Water Hardness Number SET Present Time of DAYSET Regeneration Time Sanitize the Water Softener Sanitize The Water SoftenerSanitize Your Water Softener AS Follows Adding Salt to the Storage Tank Adding Salt To The Storage TankWater Softening Salt with Iron Removing Additives Check List Check List of STEP-BY-STEP Guides to InstallFaceplate Timer Features Gallons / Liters Maximum Days Between Regenerations Gallon or Liter readings Water usage and flow dis Tank LightMaximum days between regenerstions The face Program Memory Recharge Time Remaining and Valve Position IndicatorsError Code KENMORE’S Ultra Cleansing FeatureWater Flow Through Softener in Fill Water Flow Through Softener in ServiceSoft Water Service and Regeneration How Your Water Softener WorksWater Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseAutomatic Bypass Water Flow Through Softener Fast RinseElectronics Salt Bridge Care Of Your Water SoftenerSalt Bridge Iron from Resin BED Keeping the Water Softener CleanNozzle & Venturi Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money Problem Cause CorrectionInches SpecificationsModel 383760 Timer Code H Model 393760 Timer Code H Bypass ValvesOther Specifications Always Make These Initial Checks First Service Tech InformationWiring Schematic FaceplateManual Initiated Electronics Diagnostics Procedure for Removing Error Code from FaceplatePossible Defect Code Timer PWA Replacement Troubleshooting Valve Position IndicatorsManual Advance Regeneration Check Brine Valve Float SettingCycle Flow Rates Gallons PER MIN To Relieve Pressure Rotary Valve ServiceDisassembly AssemblyFill Cycle Water Flow Through the Softener Valve Service CycleBrining and Brine Rinse Cycle Fast Rinse Cycle Water Flow Through the Softener Valve Backwash CycleFast Rinse Cycle Backwash CycleExploded View Water Softener Complete Parts ListPart Number Part Description Inlet Outlet Grounding Clamps Brine Valve Assembly Wear-Strip Seal Cross-Section View Key Part Number Part Description Get it fixed, at your home or ours
Related manuals
Manual 48 pages 29.92 Kb Manual 48 pages 54.31 Kb

625.39376, 625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents