Kenmore 625.347001 owner manual Install Cold Water Supply Saddle Valve

Page 5

-- STEP 1: INSTALL COLD WATER SUPPLY SADDLE VALVE --

Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The fitting must provide a leak- tight connection to the RO 1/4”tubing (see FIG. 8, page 8). A typical connection, using the included saddle valve is shown in FIG.3 - A below. An optional connection, using standard plumb- ing fittings (not included), is shown in B.

Note: Codes in the state of Massachusetts require instal- lation by a licensed plumber, and do not permit the use of the saddle valve. For installation, use plumbing code 248- CMR of the Commonwealth of Massa- chusetts.

A. SADDLE VALVE

Note: This valve has a cutting pin and will pierce a hole in copper tubing or plastic pipe. If installingon iron pipe, you have to drill a 1/8”hole for the pierc- ing pin. Read the following danger note and be sure to turn off water to the pipe and to drain water from it before drilling.

DANGER (if drilling metal pipe): To protect your-

FIG. 3

nut (2) --- not req’d with all types of clamp Z

clamp Z

A. WATER SUPPLY CONNECTION

(using included saddle valve)

 

pre---drill

 

 

 

1/8”hole

 

Check local

for iron pipe

codes

for

 

 

approval

 

seal

clamp X

 

 

 

valve

 

 

insert

 

 

 

self from serious injury or fatal shock, use a battery powered hand drill only to make the hole. Do not use an electric drill.

1.Close the house main water shutoff valve andopen faucets to drain water from the sink cold water pipe.

2.Observing above note and caution, drill the 1/8” diameter hole in iron pipe.

3.Looking at figure 3A, turn the valve into clamp X and tighten (maybe already assembled). Turn the valve handle all the way out.

4.Place the seal on the inside of clamp X as shown. Be sure the cutting pin does not stick out beyond the seal.

5.Place clamp X and Z around the pipe and secure in place with 2 screws. If you predrilled a 1/8” hole, align the cutting pin with it. Tighten both screws evenly, but do not overtighten. Clamp Z will either have threaded screw holes, or 2 nuts are included.

6.Carefully turn the handle inward to pierce a hole in the copper or plastic pipe.

B.OPTIONAL PIPE FITTINGS (compression type shown)

Note: Be sure to turn off the water supply and open a low faucet to drain the pipe.

Complying with plumbing codes, install a fitting on the kitchen cold water pipe to adapt 1/4”OD tubing. A typical connection is shown in figure 3B. If threaded fittings are used, be sure to use pipe joint compound or Teflon tape on outside threads.

nut

ferrule

handle

See note on codes

use to connect

 

in the state of

tubing, step 2,

 

Massachusetts,

on page 8

 

above left.

 

 

 

cold water

 

shutoff

 

B. WATER SUPPLY

 

TYPICAL CONNECTION

 

(using compression fitting)

 

- parts not included -

 

1/4”compression

 

fitting

 

insert

 

ferrule

cold

1/4”tubing to

water

RO inlet (see step

pipe

2, on page 8)

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Reverse Osmosis Drinking Water System Safety Guides WarrantyWhat Your Reverse Osmosis System will do Table of ContentsBefore YOU Begin to Install the RO System Tools and Materials Needed Where to Install the RO SystemSteps to Install Optional Pipe Fittings compression type shown Install Cold Water Supply Saddle ValveSaddle Valve Prepare Mounting Hole Install Drain AdapterInstall Faucet Assemble Faucet Install RO AssemblyTypical Undersink Installation Install Storage TANK, Make Remaining Tubing Connections7, only replace all cartridges SANITIZING, Pressure Testing & PurgingHOW Your Reverse Osmosis System Works RO Membrane Cartridge Care of Your Reverse Osmosis SystemPrefilter and Postfilter Cartridges Flow Control and Screen To clean/replace flow control and screen FIGTubing Connection Connection FIGChanging Collet and O-ring FIG Automatic Shutoff ServiceReverse Osmosis System Care Guide Dimensions and Specifications Kenmore Reverse Osmosis Drinking Water System, Model No Repair PartsKey Part Description of Part Number Remote Location for Reverse Osmosis System Remote RO InstallationPage Model no OWNER’S Manual

625.347001 specifications

The Kenmore 625.347001 is a versatile and efficient appliance that combines advanced technology with user-friendly features, making it an ideal choice for modern households. Renowned for its reliability and performance, this model boasts several characteristics that enhance its functionality and convenience.

One of the standout features of the Kenmore 625.347001 is its innovative filtration system, designed to ensure maximum air quality and odor control. The model utilizes a HEPA filter that captures even the finest particles, making it excellent for allergy sufferers. Additionally, the filter is washable, which not only makes it cost-effective but also eco-friendly, as it reduces waste.

Powerful suction is another hallmark of the Kenmore 625.347001. With its robust motor, it is capable of tackling various surfaces, from carpets to hardwood floors, efficiently. Users can adjust the suction power according to their cleaning needs, thanks to its variable suction control feature. This adaptability ensures that delicate surfaces are treated gently without compromising cleaning performance on tougher areas.

The Kenmore 625.347001 is designed for ease of use and convenience. It features an ergonomic handle and lightweight design, allowing for effortless maneuverability around the home. Its long power cord enhances reach, minimizing the need for frequent plug changes, which can disrupt the cleaning process. Furthermore, the quick-release tool caddy conveniently stores and allows easy access to a variety of attachments, such as a dusting brush, crevice tool, and upholstery nozzle.

Durability is another significant aspect of the Kenmore 625.347001. Constructed from high-quality materials, this model is built to withstand daily use, ensuring longevity and reliability. The dustbin is designed for easy emptying and cleaning, reducing maintenance time and enhancing user experience.

In terms of design, the Kenmore 625.347001 sports a sleek and modern aesthetic that fits seamlessly into any home decor. Its compact design allows for easy storage, catering to those with limited space.

Overall, the Kenmore 625.347001 stands out as a premium cleaning appliance, expertly combining efficiency, convenience, and durability, making it a valuable addition to any household.
Top Page Image Contents