Media Considerations, Location and Mounting

ChannelMag

Section 2 Installation

2.1Media

Considerations

The ChannelMag is suitable for such media as water, raw sewage, slurries, algae laden river water, and similar. The minimum media conductivity is 0.5 microS/cm for operation with pulsed AC transmitters. Most water based media has a conductivity of 200 – 800 microS/cm.

The ChannelMag may be permanently coated with sewage grease, algae, calcium carbonate, iron oxides or similar, without affecting accuracy. No cleaning is necessary. If there is non ﬂuidic sediment on the bed of the channel, then the ChannelMag should sit on the channel bed with its upper-most surface above the channel bed. Ramps are then required (see Section 2.2). All PM2 ChannelMag sensors are supplied with ramps.

Check the compatibility of the media with the wetted parts before installing. With some media its consistency and operational temperature range can affect this compatibility.

Make sure the pressure of the media acting on the sensor(s) and the operational temperature does not exceed that speciﬁed.

2.1Location and Mounting

For lifting the ChannelMag sensor, use the lifting brackets ﬁxed to the sensor, as shown on the drawing in Section 2.4. Use a min. diameter 1/8” (3mm) steel rope looped through the bracket holes for installing the ChannelMag sensors(s). Use the holes in the magnetic enhancement plates ONLY for convenience of removing the sensors from ﬂowing media, since in so doing the enhancement plates may be damaged.

The ChannelMag is highly insensitive to environmental electrical noise, including interference from radio and variable frequency drives. However, it is good practice to locate the ChannelMag and ancillary equipment away from the immediate area of such noisy environments. The ancillary electronics must be located remotely from the ChannelMag sensors. They must not be mounted under direct sunlight, or where they are subject to driving rain, where they cannot be reasonably read or serviced. For such environments they must be protected by a suitable canopy or protective housing. Avoid environments where moisture can accumulate in the electronics. A heated enclosure may be necessary to achieve this.

The ChannelMag sensors are indeﬁnitely submersible to 30 feet (10m)/ 15 psig/1 bar g. They are normally supplied with conduited cables and junction box (see data sheet in this instruction manual for details of lengths). Should the cables be extended then each cable may be spliced, soldered and all cable joint surrounded with shrink sleeves. Shielding must be extended to the same length as all other cable cores. Should a junction box be used to extend cables, it must be absolutely dry, then ﬁ lled with potting compound. We recommend 3M “High Gel” type 4442 two part, re-enterable compound, mixed 50% / 50%

. The typical drying time is 2 – 3 hours, but it never solidiﬁes hard. A metal shield 1/16” (1-2mm) thick must be placed between

Channelmag specifications

Arkon Channelmag is a dynamic digital platform designed to streamline content dissemination and enhance communication among businesses, consumers, and content producers. As a cutting-edge solution, it tailors its features to meet the diverse needs of modern audiences, emphasizing engagement, accessibility, and user-friendliness.

At its core, Arkon Channelmag utilizes a robust content management system (CMS) that allows users to create, edit, and manage digital content effortlessly. The CMS supports a variety of media formats, including text, images, videos, and interactive elements, providing a comprehensive toolkit for content creators. This versatility enables businesses to produce visually appealing and informative content that captures the attention of their target audience.

One of the standout features of Arkon Channelmag is its integration of artificial intelligence (AI) and machine learning algorithms. These technologies analyze user behavior and engagement patterns, allowing for personalized content recommendations that enhance user experience. This tailored approach not only keeps users engaged but also drives traffic to businesses by presenting them with relevant content that aligns with their interests.

Another key characteristic of Arkon Channelmag is its responsive design, which ensures that content is accessible across all devices, from desktops to smartphones. The platform’s mobile optimization is essential in today’s digital landscape, where users expect seamless experiences regardless of the device they are using. This adaptability allows businesses to reach a wider audience and fosters higher engagement rates.

The platform also prioritizes collaboration by allowing multiple users to work on content simultaneously. This feature facilitates teamwork and accelerates the content creation process, crucial for businesses aiming to stay ahead in a competitive market. Furthermore, the built-in analytics tools provide insightful metrics on content performance, enabling users to make data-driven decisions and refine their strategies accordingly.

Security is another hallmark of Arkon Channelmag, with advanced encryption protocols and compliance with data protection regulations ensuring that user data is safeguarded. This commitment to security fosters trust among users, making Arkon Channelmag a credible choice for businesses that prioritize privacy and data integrity.

In summary, Arkon Channelmag stands out in the digital landscape through its rich features, innovative technologies, and user-centric design. By focusing on content management, personalization, collaboration, and security, it equips businesses with the tools they need to thrive in a rapidly evolving digital environment.