3Com ENTERPRISE OS 11.3 manual Bcmsysupgrade -sfromnb -ftp device

Page 18

18CHAPTER 3: PLANNING AND PREPARING THE UPGRADE

On a UNIX NMS, follow these steps:

1Create a user on your system with /tftpboot as the home directory.

2When using the upgrade utilities via the command line or the Transcend Upgrade Manager, specify this user name and password in the BCMFTPUSER and BCMFTPPASS environment variables.

Specify the -ftp flag in all command line utilities that use file transfers (bcmsysupgrade, bcmbackup, bcmrestore) if you want to use FTP file transfer. For example, to specify FTP file transfer use:

bcmsysupgrade -s:from_nb -ftp <device>

If no flag is used, TFTP is used by default for software release 11.0 and lower, but FTP is used by default for software release 11.1 and higher. If the -ftp flag is specified on a bridge/router running software version 11.0 or lower, the FTP password is overwritten with the following text string:

****

On a Windows NMS, follow these steps:

1Create a user in 3Com’s 3CServer FTP settings.

2When using the upgrade utilities via command line or the Transcend Upgrade Manager, specify the ftp user name and password in the BCMFTPUSER and BCMFTPPASS environment variables.

You can specify the -ftp flag in the utilities (bcmsysupgrade, bcmbackup, bcmrestore) if you want to use FTP file transfer.

If no flag is used, TFTP is used by default for software release 11.0 and lower, but FTP is used by default for software release 11.1 and higher. If the -ftp flag is specified on a bridge/router running software version 11.0 or lower, the FTP password is overwritten with the following text string:

****

Choosing Automatic If you have enough flash memory for dual-image support, complete your upgrade

Recovery or Manual using automatic recovery. If you have only enough memory for single-image

Recoverysupport, complete the upgrade using manual recovery. The following sections describe the difference between automatic and manual recovery and the memory requirements for each platform.

Automatic Recovery The default upgrade procedure uses automatic recovery. After backing up the current software to the network management station (NMS), the new software is copied into a test directory while the current software remains in the primary directory. If you accept the upgrade after booting from the test directory, the new software becomes the primary boot source, and the old software becomes the secondary boot source.

If you are upgrading your hardware as well as the software, the procedure for automatic recovery saves the software package that was originally on the new hardware as the secondary boot source.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Upgrading Enterprise OS Software Santa Clara, California 3Com CorporationBayfront Plaza 95052-8145Contents Upgrading a BRIDGE/ROUTER Using the COMMAND-LINEUTILITIES Reference for the Upgrade Management Utilities Lossary Ndex 3COM Corporation Limited Warranty List conventions that are used throughout this guide About this GuideConventions Icon DescriptionText Conventions Convention DescriptionUpgrade Tools OverviewProcess Primary, Secondary, and Test Boot Sources Automatic or Manual RecoveryRules and Support Limitations Take Time to PlanOverview Installing the Utilities on a Network Management Station Where os is the directory for your operating system Installing the Utilities on a Unix SystemPreparing for Installation Version message may refer to Solaris 2.5 as SunOSTo install only the upgrade utilities, enter Return to normal privilege by enteringOperating System Directory Name Bcmsteup -bootp You can choose to transfer files using FTP or Tftp Planning and Preparing UpgradeSetting Up a File Transfer MethodBcmsysupgrade -sfromnb -ftp device Flash Memory Required for SuperStack II NETBuilder Token RingSuperStack II NETBuilder SI PathBuilder S5xx Switch FD FradChecking Software VersionPlanning Tables 10.1.3.24 11.0 BF Planning and Preparing the Upgrade Upgrading Using the Netbuilder Upgrade Link Application Preparing for the UpgradePrograms⇒ Remote Upgrade Utilities⇒Upgrade Link RemotelyAppears. describes the buttons on the bottom of the Status Button DescriptionAbort To the switch or bridge/router by following these steps Verifying forUpgrading You must be logged in as root for this procedure Unix Select Upgrade and click Apply Upgrade page appearsFor Windows CD-ROM, use the following path Upgrading Using the Netbuilder Upgrade Link Application Upgrading Software Upgrading Using the Netbuilder Upgrade Link Application COMMAND-LINE Utilities Setting up for FTP File Transfers Setting up for Tftp File TransfersFTP password is overwritten with the following text string Shown onInstalling Software on the NMSFor UNIX, enter To check which version you have installed, enterWindows \%tftpboot%\image\platform\SWFW\version\pkg From a Tarred File, useUsing Bcmsysupgrade UtilityTo Upgrade Filenames Lists the most common bcmsysupgrade optionsSame options must be used to upgrade configuration files NETBuilder systemPathBuilder S5xx Series Switch Copy the upgraded software to the bridge/router using Test your new software usingAccept your upgrade using Bridge/router reboots after the firmware is upgraded If the Bridge/Router or Switch Does Not BootBcmsysupgrade options -sfromnb -newhw device SETDefault -IP CONTrol = ROute Bcmsysupgrade -saccept -newhw device Enable a routing protocol. For example, enable RIP by using Bcmsysupgrade -stonb -m -newhw device Upgrading a BRIDGE/ROUTER Using the COMMAND-LINE Utilities Upgrading the Software Image Only Upgrading the Software Image only Using Upgrade Link Upgrading Select Upgrade and click Apply. The Upgrade page appears Click Home then Exit to exit Upgrade Link Command-Line UtilitiesCopy the new software to the bridge/router using Accept the upgrade usingEnterprise OS User InterfaceReboot the system by entering Backing UP and Restoring Software PrerequisitesBacking UP and Restoring Software You select and set up your file transfer method SoftwareSelect Verify Upgrade Services Diagnose Prediagnosing System ProblemsBacking Up the Software For Unix For WindowsEnable a routing protocol. For example, enable Ospf using Mapping Hostnames Using the etc/snmp.cfg File Select Verify Upgrade Services Diagnose then click Apply Verifying the Device for RestoringRestoring the Software Command-Line Prediagnosing System Problems Detect any problems with Snmp or Tftp connectivity usingWhere backname is the name of the backup for the boot blocks If you are not replacing the hardware, useReference for Upgrade Management Utilities AccessingDownloading Update Log File Utility DescriptionsSyntax Bcmbackup To access the man pages for a specific utility, useOr to access help for a specific utility, use Getting HelpBcmconfig Ftp -tftpProcess WithBcmctrl Bcmdf Bcmdiagnose Network management station BcminstallTar path Installs a tarred package file Cdrom pathBcmloadconfig -l are mutually exclusiveBcmrestore BcmnbrusBcmsetup BcmsysupgradeBcmuname Bcmupdate UpgradeLink Getting Help TroubleshootingTroubleshooting Error GeneralCode Meaning Installation Troubleshooting MessagesHardware-Related Not consistent Validating the Snmp Testing Snmp read accessRequired programs Determining Pinging IP address ConnectivitySnmp write access OK Snmp read access OKTesting Snmp write access Creating an Upgrade FileRemote test files Action Check with your systems administrator MeaningMeaning This is a status message Action None Meaning This is an information message Action NoneDownloading an Upgrade File File transfers using Tftp are OKAppendix a Troubleshooting NETBuilder II Upgrade Choosing a Software PackageMigration Path Recommended Upgrade From Version To VersionFrom Version 8.2/8.3 To Version NETBuilder II Software Package Migration to NETBuilder Upgrade SuperStackFrom Version To Version 42x Series From Version 8.0/8.1 From Version 9.0/9.1/9.3/10.1 To Version32x Series From Version 8.3/9.0/9.1/9.3 To Version From Version 9.0/9.1/9.3 To VersionNETBuilder SI Upgrade OfficeConnect OfficeConnect Software Package Migration toFrom Version 10.2 model To Version 13x only PathBuilder Software Package Migration to Appendix B Choosing a Software Package CD-ROM on Mounting the CD-ROMON a C Unix PlatformMounting SolarisEnter At the command prompt on the remote system, enterChange directories to /etc/init.d and enter You may need to start the NFS daemonsMounting the CD-ROM on HP-UX Remote CD-ROM DriveOpen a command window Insert the CD-ROM Enter Mounting the CD-ROM on IBM AIX 4.1.x ThroughUnmounting CD-ROMAppendix C Mounting the CD-ROMON a Unix Platform Services Technical SupportOnline Technical 847 262 Access by Analog ModemAccess by Digital Modem 408 727Europe, South Africa, and Middle East Country Telephone Number Asia Pacific RimEurope Latin AmericaCountry Telephone Number Fax Number Glossary NMS See network management station Glossary Glossary Index NumbersIndex 3Com Corporation Limited Warranty Disclaimer

ENTERPRISE OS 11.3 specifications

3Com Enterprise OS 11.3 is a robust network operating system designed specifically for enterprise-level applications, offering a comprehensive suite of features and technologies that enhance network performance, reliability, and security. Engineered for the needs of large organizations, this operating system integrates advanced functionalities that ensure efficient management of network resources.

One of the key features of 3Com Enterprise OS 11.3 is its enhanced routing capabilities. It supports dynamic routing protocols like OSPF and RIP, ensuring optimal path selection and efficient use of network bandwidth. This enables seamless communication across multiple network segments, reducing latency and improving overall system responsiveness.

Another significant characteristic of this OS is its powerful network management tools. The built-in management functionalities provide administrators with an intuitive interface to monitor, configure, and troubleshoot network devices in real time. With features like SNMP (Simple Network Management Protocol) support, network visibility is improved, allowing for efficient performance monitoring and rapid response to potential issues.

Security is a critical focus for 3Com Enterprise OS 11.3, which includes comprehensive measures such as access control lists (ACLs), robust authentication methods, and support for Virtual Private Networks (VPNs). These security features safeguard sensitive data and ensure that only authorized users can access network resources, mitigating the risk of unauthorized access and potential data breaches.

The operating system is also designed for scalability, accommodating the growing needs of enterprise environments. Its modular architecture allows for the integration of additional features and services without sacrificing performance. This flexibility makes it suitable for both small businesses and large enterprises, adapting to various networking requirements as they evolve.

Furthermore, 3Com Enterprise OS 11.3 facilitates quality of service (QoS) management, which prioritizes critical network traffic. By ensuring that time-sensitive applications receive the bandwidth they need, the OS enhances the performance of voice, video, and data services, which is crucial for maintaining high productivity levels.

In summary, 3Com Enterprise OS 11.3 stands out with its advanced routing capabilities, robust network management tools, enhanced security features, scalability, and QoS management. These characteristics make it an ideal solution for enterprises seeking a reliable and efficient network operating system to support their complex networking needs.
Top Page Image Contents