Craftsman Official Installation Manual for Olo Carton Opener - Garage Door Opener
Page 18

Installation

Step 6

I

Install the Door

Control

Locate the door control within sight of the door at a minimum height of 5 feet where small children

cannot reach, and away from all moving parts of the door and door hardware.

The door control is typically attached directly to the wall. If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), Console models may be mounted to a standard single gang box (Figure 2).

1.Strip 1/4" of insulation from one end of the bell wire and connect it to the two screw terminals on the back of the door control: white to 2 and white/red to 1.

2.Pry off cover along one side with a screwdriver blade (Figure 1). Fasten with 6ABx1-1/4" self- tapping screws (standard installation) or 6-32x1" machine screws (pre-wired installation) as follows:

•Install bottom screw, allowing 1/8" to protrude above wall surface.

•Position bottom of door control on screw head

and slide down to secure. Adjust screw for snug fit.

Do not connect to live electrical wiling. Connect only to 24 Volt/oH, voltage wires. Connection to live wires or higher voltage may cause serious injury from shock, burn or electrocution.

Children operating or playing with a garage

door opener can injure themselves or others. The garage door could close and cause

serious injury or death.

Install the door control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible.

Do not allow children to operate the push button(s) or the remote control(s).

A moving garage door could injure someone under it. Activate the opener only when the door is properly adjusted, you can see it clearly, and there are no obstructions to door travel.

Hardware

Shown

Actual Size

_ UihJIlnJIlilililil

Ililn_

Insulated

6AB x 1-1/4" Screw

Control Console (std installation)

Staples

•Install top screw with care to avoid cracking plastic housing. Do not overtighten.

•Insert top tabs and snap on cover.

3.(For standard installation only) Run the bell wire up the wall and across the ceiling to the opener.

Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, creating a short.

4.Connect the bell wire to the terminal screws on the opener panel: white to 2; white/red to 1.

5.Position the antenna wire as shown.

2-Condustor Ben Wim

BACK

STANDARD

CONTROL

CONSOLE

Control

Console

(pre*wired)

Dry Wall Anchors

Figure

1

 

Figure 2

REMOVE

& REPLACE

COVER

PRE-WlRED

To Replace,

 

 

To Remove,

INSTALLATION

 

 

 

Insert

 

 

 

Twist

 

Top Tabs

 

.

•

Here

 

First

• •

 

•

 

 

24 Volt

2-Condustor Bell Wire

VIEW

of Opener

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Garage Door Opener Start by reviewing these important safety alert symbols Instructions. Read the instructions carefullyYoull Need Tools Safety Based on your particular requirements, there areClosed Position One-Piece Door with Track One-Piece Door without TrackClosed Position Carton Inventory SectionSafety Reversing Sensor @ @Assembly Section Pages 8 Assembly StepInstall the Idler Pulley Fasten the Rail to the OpenerHardware Shown Actual Size Install the Chain/Cable Attach the Sprocket Cover Master Link Clip-OnSpdng Unk CapTighten Chain = Lo Tro,.yInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , One-piece door without track Jamb hardware ExampleInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Insert a ring fastener to securePosition the Opener With the door fully open and parallel to the floorInstallation Step Hang the OpenerSerious injury or death Install the Door ControlSlide down to secure. Adjust screw for snug fit Shown Actual Size UihJIlnJIlilililil IlilnInstall the lens Install the Light and the LensInstall the light Attach the Emergency Release Rope and HandlePermanent Widng Connections Electrical RequirementsRightWrong Safety Reversing System Important Information about Safety Reversing SensorBe sure power to the opener is disconnected Sensor Safety ReversingInstalling the Brackets Garage door track installation preferredMounting and Wiring the Safety Sensors Aligning the Safety SensorsTrouble Shooting the Safety Sensors IIIIIlllillllILllllllllllllllll Fasten Door BracketIIIIIII11111111LLLIIIIIlI NutConnect Door Arm to Trolley RBokAbove holes Adjustment Procedures for One-Piece Doors Adjust the UP and Down Limits Adjustment Section Pages 28 Adjustment StepHow and When to Adjust the Limits Adjustment Step If the door does not close completelyAdjust the Force How and When to Adjust the ForcesImportant safety check Test The Safety Reversing SensorTest the Safety Reverse System Press the remote control push button to open the doorMaintenance To reduce the risk of severe injury or death to personsSchedule Operation of Your Opener Operation of the Door Control seeManual disconnect Position If you do not have a Premium Control Console Receiver and Remote Control ProgrammingIf you have a Premium Control Console SECURITY,IHaving a Problem? Situation Probable Cause and SolutionOpener lights blink for 5 seconds Situation Probable Cause SolutionDoor opens but Doesnt turn offRepair Parts Rail Assembly PartsInstallation Parts Opener Assembly Parts Br co.tact ASSEMe,vFor Sectional Doors Onl AccessoriesOnly through Sears Parts & Service With the door closedIndex For in-homemajor brand repair service Sears WarrantyPara ordenar piezas con entrega a domicilio

139.53978SRT specifications

The Craftsman 139.53978SRT is an advanced garage door opener that combines reliability, performance, and ease of use. Designed to cater to the needs of modern homeowners, this model stands out with its robust features and technological innovations.

One of the key highlights of the Craftsman 139.53978SRT is its powerful motor, delivering a peak horsepower equivalent to ensure smooth and efficient operation. This allows it to effortlessly lift even the heaviest of garage doors, making it suitable for various types of residential garage doors. The quiet operation of this opener is another major advantage, allowing for a peaceful environment in and around the garage.

Another notable feature is the smart technology integration. The Craftsman 139.53978SRT is compatible with a range of smart home systems, allowing users to control their garage door remotely via a smartphone app. This feature not only adds convenience but also enhances security, as users can receive alerts and notifications about the status of their garage door, ensuring peace of mind.

Security is a priority with this model, which comes equipped with rolling code technology. This mechanism generates a new code each time the remote is used, preventing unauthorized access and ensuring that your garage remains secure from intruders. Additionally, the enhanced safety features include safety sensors that detect obstacles, automatically reversing the door's movement if something is detected, thereby preventing accidents.

Installation and setup are straightforward, thanks to the user-friendly design of the Craftsman 139.53978SRT. The unit includes detailed instructions and all necessary hardware for installation. Many users can set it up within a few hours without the need for professional assistance.

With a durable construction, the Craftsman 139.53978SRT is built to last. It has a sleek design that complements various home aesthetics while withstanding wear and tear from daily use. Maintenance is minimal, with easy access to essential components for servicing.

In summary, the Craftsman 139.53978SRT offers a perfect blend of power, technology, and security features. Its user-friendly design, combined with smart technology compatibility and robust safety measures, makes it an ideal choice for homeowners seeking a reliable garage door opener. Whether you’re looking to upgrade an old system or install a new one, this model is sure to meet your requirements and enhance the functionality of your garage.
Top Page Image Contents