Craftsman 139.53978SRT owner manual Receiver and Remote Control Programming, Security,I

Page 33

Receiver and Remote Control Programming

SE( URri '.F

Your garage door opener receiver and remote control have been pre-setat the factory. The door will open when you press the LARGE remote control push button. The code between the remote control and the receiver changes with each use, randomly accessing over 100 billion new codes. The 3-function remote control can also activate additional SECURITY,I, garage door openers and/or light controls.

Your SECURITY+ opener will operate with:

•several SECURITY,I, remote controls (with blue push buttons) utilizing up to 8 functions.

•one SECURITY+ Keyless Entry System (Model 139.53684).

Follow the instructions below to program your opener to match any additional remotes you may _urchase. See Accessories on page 38.

To complywdhFCC rules,adjustmento¢modificationsof this receiverandfor transmitterare prohtbRed,except for changingthe code settingor replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Children operating or playing with a garage door opener can injure themselves or others.

The garage door could close and cause setfous injury or death. Do not allow children to operate the door push button(s) or remote control(s).

A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door clearly, it is free of obstructions, and is properly adjusted.

To Add A Remote Control

If you have a Premium Control Console:

1.With the doorc/osed, press and hold a remote control push button. See Figure 1.

2.Press and hold the Light button on the door control.

3.Press and hold the door control push button.

4.After the opener light flashes, release all buttons. Test by pressing the remote push button.

If you do not have a Premium Control Console:

1.Press and holdthe selected remote control push button. See Figure 1.

2.Then press and release the SRT (learn) button on the back panel of the opener, Figure 2. The indicator light on the panel will begin to blink and the opener light will flash once.

3. Release the remote push button.

Test by pressing the remote push button.

Figure I

Select a remote control push button to operate opener

SECURITY'I' 3-Function Remote Control

Figure 2

SECURITY,I,

Garage Door Opener

SRT (leam) Indicator BACK

Button Ught PANEL

To Erase All Remote Control Codes

Press and hold the SRT button on the opener panel until the indicator light turns off (about 6 seconds). All remote control codes are now erased. Then

follow the steps above to re-program each remote control.

Code programming instructions are

also located on the opener panel,

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Garage Door Opener Instructions. Read the instructions carefully Start by reviewing these important safety alert symbolsYoull Need Tools Safety Based on your particular requirements, there areClosed Position One-Piece Door with Track One-Piece Door without TrackClosed Position Section Carton Inventory@ @ Safety Reversing SensorAssembly Step Assembly Section Pages 8Install the Idler Pulley Fasten the Rail to the OpenerHardware Shown Actual Size Master Link Clip-OnSpdng Unk Cap Install the Chain/Cable Attach the Sprocket Cover= Lo Tro,.y Tighten ChainInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , Example One-piece door without track Jamb hardwareInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Insert a ring fastener to secure Attach the Rail to the Header BracketWith the door fully open and parallel to the floor Position the OpenerHang the Opener Installation StepSlide down to secure. Adjust screw for snug fit Install the Door ControlSerious injury or death Shown Actual Size UihJIlnJIlilililil IlilnInstall the light Install the Light and the LensInstall the lens Attach the Emergency Release Rope and HandlePermanent Widng Connections Electrical RequirementsRightWrong Important Information about Safety Reversing Sensor Safety Reversing SystemInstalling the Brackets Sensor Safety ReversingBe sure power to the opener is disconnected Garage door track installation preferredMounting and Wiring the Safety Sensors Aligning the Safety SensorsTrouble Shooting the Safety Sensors Fasten Door Bracket IIIIIlllillllILllllllllllllllllNut IIIIIII11111111LLLIIIIIlIConnect Door Arm to Trolley RBokAbove holes Adjustment Procedures for One-Piece Doors How and When to Adjust the Limits Adjustment Section Pages 28 Adjustment StepAdjust the UP and Down Limits Adjustment Step If the door does not close completelyHow and When to Adjust the Forces Adjust the ForceTest the Safety Reverse System Test The Safety Reversing SensorImportant safety check Press the remote control push button to open the doorMaintenance To reduce the risk of severe injury or death to personsSchedule Operation of Your Opener Operation of the Door Control seeManual disconnect Position If you have a Premium Control Console Receiver and Remote Control ProgrammingIf you do not have a Premium Control Console SECURITY,ISituation Probable Cause and Solution Having a Problem?Door opens but Situation Probable Cause SolutionOpener lights blink for 5 seconds Doesnt turn offRepair Parts Rail Assembly PartsInstallation Parts Br co.tact ASSEMe,v Opener Assembly PartsOnly through Sears Parts & Service AccessoriesFor Sectional Doors Onl With the door closedIndex For in-homemajor brand repair service Sears WarrantyPara ordenar piezas con entrega a domicilio

139.53978SRT specifications

The Craftsman 139.53978SRT is an advanced garage door opener that combines reliability, performance, and ease of use. Designed to cater to the needs of modern homeowners, this model stands out with its robust features and technological innovations.

One of the key highlights of the Craftsman 139.53978SRT is its powerful motor, delivering a peak horsepower equivalent to ensure smooth and efficient operation. This allows it to effortlessly lift even the heaviest of garage doors, making it suitable for various types of residential garage doors. The quiet operation of this opener is another major advantage, allowing for a peaceful environment in and around the garage.

Another notable feature is the smart technology integration. The Craftsman 139.53978SRT is compatible with a range of smart home systems, allowing users to control their garage door remotely via a smartphone app. This feature not only adds convenience but also enhances security, as users can receive alerts and notifications about the status of their garage door, ensuring peace of mind.

Security is a priority with this model, which comes equipped with rolling code technology. This mechanism generates a new code each time the remote is used, preventing unauthorized access and ensuring that your garage remains secure from intruders. Additionally, the enhanced safety features include safety sensors that detect obstacles, automatically reversing the door's movement if something is detected, thereby preventing accidents.

Installation and setup are straightforward, thanks to the user-friendly design of the Craftsman 139.53978SRT. The unit includes detailed instructions and all necessary hardware for installation. Many users can set it up within a few hours without the need for professional assistance.

With a durable construction, the Craftsman 139.53978SRT is built to last. It has a sleek design that complements various home aesthetics while withstanding wear and tear from daily use. Maintenance is minimal, with easy access to essential components for servicing.

In summary, the Craftsman 139.53978SRT offers a perfect blend of power, technology, and security features. Its user-friendly design, combined with smart technology compatibility and robust safety measures, makes it an ideal choice for homeowners seeking a reliable garage door opener. Whether you’re looking to upgrade an old system or install a new one, this model is sure to meet your requirements and enhance the functionality of your garage.
Top Page Image Contents