Craftsman 139.53978SRT owner manual Safety Reversing System

Page 21

The Safety Reversing System

IMPORTANT INFORMATION ABOUT THE

SAFETY REVERSING SENSOR

The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. This is a required safety device and cannot be disabled.

When properly connected and aligned, the safety reversing sensor will detect an obstacle in the path of its electronic beam. The sending eye (with an orange indicator light) transmits an invisible light beam to the receiving eye (with a green indicator light). If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to

full open position, and the opener light will flash 10 times.

The units must be installed inside the garage so

that the sending and receiving eyes face each other across the door, between 4 - 6" above the floor.

Either can be installed on the left or right of the door as long as the sun never shines directly into the receiving eye lens.

The mounting brackets are designed to clip onto the track of sectional garage doors without additional hardware.

Without a properly working safety reversing sensor, persons (particularly children) could

be injured or killed by a closing garage door. Read and follow all instructions,

To protect small children, install the safety reversing sensor so that the beam will be between 4 - 6" above the garage floor.

Disconnect power to the garage door opener before installing the safety reversing sensor,

If it is necessary to mount the units on the wall, the brackets must be securely fastened to a solid surface such as the wall framing. Extension brackets (see accessories) are available if needed. If installing in masonry construction, add a piece of wood at each location to avoid drilling extra holes in masonry if repositioning is necessary.

The invisible light beam path must be unobstructed. No part of the garage door (or door tracks, springs, hinges, rollers or other hardware) may interrupt the beam while the door is closing.

Sensor Beam

4-6" max, above floor

1

0[

I

 

I

k

Sortsor B6am 4-6" max,

above floor

Invisible Light Beam

Protection Area

Figure 1: Facing the door from inside the garage

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Garage Door Opener Instructions. Read the instructions carefully Start by reviewing these important safety alert symbolsYoull Need Tools Safety Based on your particular requirements, there areClosed Position One-Piece Door with Track One-Piece Door without TrackClosed Position Section Carton Inventory@ @ Safety Reversing SensorAssembly Step Assembly Section Pages 8Install the Idler Pulley Fasten the Rail to the OpenerHardware Shown Actual Size Master Link Clip-OnSpdng Unk Cap Install the Chain/Cable Attach the Sprocket Cover= Lo Tro,.y Tighten ChainInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , Example One-piece door without track Jamb hardwareInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Insert a ring fastener to secure Attach the Rail to the Header BracketWith the door fully open and parallel to the floor Position the OpenerHang the Opener Installation StepSlide down to secure. Adjust screw for snug fit Install the Door ControlSerious injury or death Shown Actual Size UihJIlnJIlilililil IlilnInstall the light Install the Light and the LensInstall the lens Attach the Emergency Release Rope and HandlePermanent Widng Connections Electrical RequirementsRightWrong Important Information about Safety Reversing Sensor Safety Reversing SystemInstalling the Brackets Sensor Safety ReversingBe sure power to the opener is disconnected Garage door track installation preferredMounting and Wiring the Safety Sensors Aligning the Safety SensorsTrouble Shooting the Safety Sensors Fasten Door Bracket IIIIIlllillllILllllllllllllllllNut IIIIIII11111111LLLIIIIIlIConnect Door Arm to Trolley RBokAbove holes Adjustment Procedures for One-Piece Doors How and When to Adjust the Limits Adjustment Section Pages 28 Adjustment StepAdjust the UP and Down Limits Adjustment Step If the door does not close completelyHow and When to Adjust the Forces Adjust the ForceTest the Safety Reverse System Test The Safety Reversing SensorImportant safety check Press the remote control push button to open the doorMaintenance To reduce the risk of severe injury or death to personsSchedule Operation of Your Opener Operation of the Door Control seeManual disconnect Position If you have a Premium Control Console Receiver and Remote Control ProgrammingIf you do not have a Premium Control Console SECURITY,ISituation Probable Cause and Solution Having a Problem?Door opens but Situation Probable Cause SolutionOpener lights blink for 5 seconds Doesnt turn offRepair Parts Rail Assembly PartsInstallation Parts Br co.tact ASSEMe,v Opener Assembly PartsOnly through Sears Parts & Service AccessoriesFor Sectional Doors Onl With the door closedIndex For in-homemajor brand repair service Sears WarrantyPara ordenar piezas con entrega a domicilio

139.53978SRT specifications

The Craftsman 139.53978SRT is an advanced garage door opener that combines reliability, performance, and ease of use. Designed to cater to the needs of modern homeowners, this model stands out with its robust features and technological innovations.

One of the key highlights of the Craftsman 139.53978SRT is its powerful motor, delivering a peak horsepower equivalent to ensure smooth and efficient operation. This allows it to effortlessly lift even the heaviest of garage doors, making it suitable for various types of residential garage doors. The quiet operation of this opener is another major advantage, allowing for a peaceful environment in and around the garage.

Another notable feature is the smart technology integration. The Craftsman 139.53978SRT is compatible with a range of smart home systems, allowing users to control their garage door remotely via a smartphone app. This feature not only adds convenience but also enhances security, as users can receive alerts and notifications about the status of their garage door, ensuring peace of mind.

Security is a priority with this model, which comes equipped with rolling code technology. This mechanism generates a new code each time the remote is used, preventing unauthorized access and ensuring that your garage remains secure from intruders. Additionally, the enhanced safety features include safety sensors that detect obstacles, automatically reversing the door's movement if something is detected, thereby preventing accidents.

Installation and setup are straightforward, thanks to the user-friendly design of the Craftsman 139.53978SRT. The unit includes detailed instructions and all necessary hardware for installation. Many users can set it up within a few hours without the need for professional assistance.

With a durable construction, the Craftsman 139.53978SRT is built to last. It has a sleek design that complements various home aesthetics while withstanding wear and tear from daily use. Maintenance is minimal, with easy access to essential components for servicing.

In summary, the Craftsman 139.53978SRT offers a perfect blend of power, technology, and security features. Its user-friendly design, combined with smart technology compatibility and robust safety measures, makes it an ideal choice for homeowners seeking a reliable garage door opener. Whether you’re looking to upgrade an old system or install a new one, this model is sure to meet your requirements and enhance the functionality of your garage.
Top Page Image Contents