Craftsman 139.53626SR - I/2HP, 139.53515SR - I/2HP Onepiecedoor, Line, Door--HeaderWall Bracket

Page 15

Installation

STEP 9 Install Door Bracket and Plate

Follow instructions which apply to your door type as Illustrated below.

ALWAYS RE NFORCE THE NSIDE OF DOOR--BOTH VERTICALLY AND HOR ZONTALLY--W TH 2x4 TO PREVENT DAMAGE TO LIGHTWEIGHT AND METAL GARAGE DOORS OR ONES WITH GLASS PANELS BOARDS OR ANGLE IRON.

The horizontal brace should be st least 6 feet long. The vertical brace should cover height of top panel. Check with your garage door manufacturer for a door re=nforcement kit for an opener installs[ion.

Sectional Door Installation Procedure

Header

B_acket

VeStal

SECTIONAL DOOR

Center

 

Line

 

DoorBradder& plate Assy,

Top of Door

1.Assemble door bracket and plate as shown. Center bracket on previously marked vertical guideline.

2.Position the bracket assembly on the face of the door within the following limits:

A)The top edge of the bracket 2"- 4" below the top edge of the door.

B)Directly below any structural support across the top of the door.

Placement depends on your particular needs.

3, Mark and drill 5/16" TOP and BOTTOM fastening holes, Secure bracket as shown.

DoorBrad_t

Ptate

Nut

Reinfomernent

Board far

Lightw_ht Doors

ReinforcementBoard

Washer 5/16"

One-Piece Door Installation Procedure

NOTE: Door bracket has left and right side fastening holes. Assemble and install the door bracket and plate if your installation requires top and bottom fastening holes.

1, Center bracket (with or without plate as required) on top edge of door as shown. Mark holes.

2.Drill two 5/16" holes and fasten the door bracket with hardware supplied.

NOTE: If the door has no exposed framing, drill 3/16" pilot holes and use 5/16" x 1-1/2" lag screws (not sup- plied) to fasten bracket to top of door.

NOTE: The door bracket may be installed on face of door if required for your installation. (Refer to dotted line drawing.) HOWEVER, drill 3/16" pilot holes and substitute 5/16"x 1-1/2" lag screws (not supplied) to fasten the bracket to the door.

ONEPIECEDOOR

Door--HeaderWall --

Bracket

Optional

DoorBracket

Face of Door

Plate

Inst.'zllation

 

(Optional)

Vertical

 

Cenler--

 

Une

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model 139.53626SR I/2HP Model 139.53515SR I/2HP ContentsEEP Garage Safety Reverse System Test is VeryAttempt Loosen Move or Adjust Make Needed Adjustments Do not Wear RINGS, Watches or LooseCare of the Opener Features of Your Opener SpecificationsAccessories Youll Need Tools Assembly Hardware InstallationCarefully AssemblyAssemble Tee Rail & Attach Cable Pulley Bracket Cablepulleybracket AttachestoFRONT ENDofteerailLod Slide trolley assembly along rail to screwdriver stopAttach Tee Rail To Opener Chassis LockWasherInstall Chain and Cable Remove ScrewdriverAttach Sprocket Cover to Chassis Tighten the Chain and Cable StepExample InstallationInstallation Piece Door Without Track Installation Sectional Door Piece Door with TrackPosition Opener Chassis Installation Sectional & ONE-PIECE Door with TrackInstallation ONE-PIECE Door With no Track Attach Tee Rail to Header Bracket16LockWasher 5/16-18Nut Attach Emergency Release Rope & HandleOperation of Wall Control Wall Controlpush BAR Lock FeatureLight Feature Wiring Instructions for AccessoriesPermanent Wiring Connection Install Lights and LensesConnect Electric Power Installing LensOnepiecedoor LineDoor--HeaderWall Bracket Connect Door Arm to Trolley Sectional Door InstallationONE-PIECE Door Installation Adjustment ProceduresForce Adjustment Chart AdjustmentAdjust UP and Down Limits Limit Adjustment ChartTest Safety Reverse System Repeat Adjustment AfterOptional Instafl Infrared Reversing Sensor SET Receiver to Match SET Code Switches in ALL Transmitters to Matching PositionsSeries with Receiver Code Switches MATCH/CHANGE the Code in TransmittersDoor Wont Close Having a Problem?Probable Cause & Solution SituationUnit Must be Grounded Do not Turn onDescription Repair PartsInstallation Parts List KEY PartOown DriveWire Gear Contact Contact WireKEY Part NO. NO. Description Not ShownSears Warranty HOW to Order Repair Parts139.53626SR

139.53626SR - I/2HP, 139.53515SR - I/2HP specifications

The Craftsman 139.53626SR and 139.53515SR are two remarkable garage door openers that deliver reliable performance and advanced features ideal for both residential and commercial applications. Both models are powered by a robust ½ horsepower motor, providing a strong lift capability that can handle various types of garage doors.

One of the main features of the Craftsman 139.53626SR is its quiet operation. Designed with a belt drive system, it minimizes noise while delivering consistent performance. This makes it an excellent choice for homes where the garage is attached to the living space. The unit is also equipped with a soft-start and soft-stop feature, which ensures gentle movement of the door, further reducing noise and extending the lifespan of the garage door system.

The Craftsman 139.53515SR, on the other hand, incorporates a chain drive mechanism which is known for its durability and strength. This model is perfect for heavier doors or commercial applications where durability is crucial. It is built to withstand the rigors of frequent use and features a robust frame designed for long-lasting performance.

Both models include advanced safety features such as the infrared safety sensors that prevent the door from closing if something is detected in its path, thereby reducing the risk of accidents. They also come with a multi-function wall console, allowing for easy operation and access to settings like the vacation lock and door light control.

In terms of technology, the Craftsman openers are equipped with a security code system that changes the access code each time the remote is used. This feature enhances security by minimizing the risk of unauthorized access. Furthermore, both models are compatible with smartphone control options when paired with additional Craftsman connectivity accessories, providing users with the convenience of operating their garage doors remotely.

Setting up the Craftsman 139.53626SR and 139.53515SR is straightforward, thanks to the included installation manuals and clear instructions. Both models are designed for easy installation, making them ideal for DIY enthusiasts.

Overall, whether you choose the 139.53626SR for its quiet performance or the rugged 139.53515SR for its strength, both Craftsman garage door openers deliver reliability, advanced features, and safety, making them excellent additions to any home or business.
Top Page Image Contents