Craftsman 139.53626SR - I/2HP Operation of Wall Control Wall Controlpush BAR, Lock Feature

Page 13

Installation

STEP 6 In,t . WallControl

LOCATE WALL CONTROL (OR ANY ADDITIONAL PUSH BUTTONS) WHERE GARAGE DOOR IS VISIBLE, AWAY FROM DOOR AND DOOR HARDWARE AND OUT OF REACH OF CHILDREN. SERIOUS PERSONAL INJURY FROM A MOVING GARAGE DOOR MAY RESULT FROM MISUSE OF OPENER. DO NOT ALLOW CHILDREN TO OPERATE WALL PUSH BUTTON(S) OR TRANSMITTER.

FASTEN CAUTION LABEL ON THE WALL NEAR THE WALL CONTROL AS A REMINDER OF SAFE

OPERATING PROCEDURES.

k Wall Control

TerminalScrews

4-Strand BellWire

O_eNe(

PROCEDURE: There are 4 screw terminals on the back of the Wall Control. Connect the bell wire by color; white to white, yellow to yellow, black to black and red to red.

Fasten Wall Control to an inside garage wall with 6ABx 1" sheet metal screws provided (use anchors if installing into drywall). A convenient place is beside the service door and

OUT OF REACH OF CHILDREN.

Run the bell wire up the wall and across the ceiling to the garage door opener. Use insulated staples.

The receiver terminals as well as the antenna ere located

on the right side panel of the opener. Position antenna wire as shown. Then connect the bell wire to the terminal

screws according to color.

Terminal Screws

R_ht S_de

Panel

Staples

Wall ConTrol

Pushbuilon

OPERATION OF WALL CONTROL

WALL CONTROLPUSH BAR

Press to open _ close door.

Press again to REVERSE door during the CLOSING cycle or to STOP door during OPENING cycle.

LOCK FEATURE

Activate Lock feature only when door Is closed.

The Lock _ature was designed to prevent of_rstion of the doo_ from portable transmitters.

The door will OPEN from the Wall Control push bar, Key

Switch and Touch Code Transmitter.The door will CLOSE if the Wall Control push bar is pressed and held until the door fully closes. If the push bar is released before down travel is completed, the door will reverse.

TO ACTIVATE: Press the Lock push button. The indicator light MUST turn ON.

TO TURN OFF: Press the Lock push button again. The

indicator light MUST turn off. Opener will return to normal operation.

LIGHT FEATURE

TO ACI"IVATE: Press the Light push button. The indicator light MUST turn ON. Opener light will turn on (or remain on if opener is still In 4-1/2 minute automatic cycle).

TO TURN OFF: Press the Light push button again.

Opener light will turn off.

NOTE: To tom opener light OFF dudng 4-1/2 minute automatic cycle, press the Light push button twice - to activate and then to turn off the Light Features The light will turn OFF Immediately..

WIRING INSTRUCTIONS FOR ACCESSORIES

Infrared Reversing System:

To white & black opener terminals

Key Switch:

To red & white opener terminals

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model 139.53626SR I/2HP Model 139.53515SR I/2HP ContentsAttempt Loosen Move or Adjust Safety Reverse System Test is VeryMake Needed Adjustments Do not Wear RINGS, Watches or Loose EEP GarageCare of the Opener Specifications Features of Your OpenerAccessories Youll Need Tools Assembly Hardware InstallationAssemble Tee Rail & Attach Cable Pulley Bracket AssemblyCablepulleybracket AttachestoFRONT ENDofteerail CarefullyAttach Tee Rail To Opener Chassis Slide trolley assembly along rail to screwdriver stopLockWasher LodRemove Screwdriver Install Chain and CableAttach Sprocket Cover to Chassis Tighten the Chain and Cable StepInstallation Piece Door Without Track InstallationInstallation Sectional Door Piece Door with Track ExampleInstallation ONE-PIECE Door With no Track Installation Sectional & ONE-PIECE Door with TrackAttach Tee Rail to Header Bracket Position Opener Chassis16LockWasher 5/16-18Nut Attach Emergency Release Rope & HandleLight Feature Lock FeatureWiring Instructions for Accessories Operation of Wall Control Wall Controlpush BARConnect Electric Power Install Lights and LensesInstalling Lens Permanent Wiring ConnectionLine OnepiecedoorDoor--HeaderWall Bracket ONE-PIECE Door Installation Sectional Door InstallationAdjustment Procedures Connect Door Arm to TrolleyAdjust UP and Down Limits AdjustmentLimit Adjustment Chart Force Adjustment ChartRepeat Adjustment After Test Safety Reverse SystemOptional Instafl Infrared Reversing Sensor Series with Receiver Code Switches SET Code Switches in ALL Transmitters to Matching PositionsMATCH/CHANGE the Code in Transmitters SET Receiver to MatchProbable Cause & Solution Having a Problem?Situation Door Wont CloseUnit Must be Grounded Do not Turn onInstallation Parts List Repair PartsKEY Part DescriptionKEY Part NO. NO. Description DriveWire Gear Contact Contact WireNot Shown OownHOW to Order Repair Parts Sears Warranty139.53626SR

139.53626SR - I/2HP, 139.53515SR - I/2HP specifications

The Craftsman 139.53626SR and 139.53515SR are two remarkable garage door openers that deliver reliable performance and advanced features ideal for both residential and commercial applications. Both models are powered by a robust ½ horsepower motor, providing a strong lift capability that can handle various types of garage doors.

One of the main features of the Craftsman 139.53626SR is its quiet operation. Designed with a belt drive system, it minimizes noise while delivering consistent performance. This makes it an excellent choice for homes where the garage is attached to the living space. The unit is also equipped with a soft-start and soft-stop feature, which ensures gentle movement of the door, further reducing noise and extending the lifespan of the garage door system.

The Craftsman 139.53515SR, on the other hand, incorporates a chain drive mechanism which is known for its durability and strength. This model is perfect for heavier doors or commercial applications where durability is crucial. It is built to withstand the rigors of frequent use and features a robust frame designed for long-lasting performance.

Both models include advanced safety features such as the infrared safety sensors that prevent the door from closing if something is detected in its path, thereby reducing the risk of accidents. They also come with a multi-function wall console, allowing for easy operation and access to settings like the vacation lock and door light control.

In terms of technology, the Craftsman openers are equipped with a security code system that changes the access code each time the remote is used. This feature enhances security by minimizing the risk of unauthorized access. Furthermore, both models are compatible with smartphone control options when paired with additional Craftsman connectivity accessories, providing users with the convenience of operating their garage doors remotely.

Setting up the Craftsman 139.53626SR and 139.53515SR is straightforward, thanks to the included installation manuals and clear instructions. Both models are designed for easy installation, making them ideal for DIY enthusiasts.

Overall, whether you choose the 139.53626SR for its quiet performance or the rugged 139.53515SR for its strength, both Craftsman garage door openers deliver reliability, advanced features, and safety, making them excellent additions to any home or business.
Top Page Image Contents