Craftsman 139.53515SR - I/2HP Install Lights and Lenses, Connect Electric Power, Installing Lens

Page 14

Installation

STEP 7 Install Lights and Lenses

Make sure antenna wire is bent down before installing lights and lenses.

Install a 75 Watt maximum light bulb in each socket as shown. The lights will turn on and remain lit for 4-1/2

minutes when power i-sconnected. After 4-1/2 minutes they will turn off. For constant light, press the Light push button on the Wall Control.

If light bulbs burn out prematurely due to vibration,

replace with bulbs specifically packaged for "Garage

Door Openers".Lens

Tab

INSTALLING LENS:

NOTE: Force and limit adjustment settings are located on opener side panels. For convenience, lenses may be installed after Adjustment Step 3, Page 18.

Slide each lens into the guides as shown. Snap bottom tabs into lens slots.

75 Watt Max.

Guide

LightLensBUlb

f//

STEP 8 Connect Electric Power

TO AVOID SERIOUS PERSONAL INJURY FROM ENTANGLEMENT, REMOVE ALL ROPES CONNECTED TO THE GARAGE DOOR BEFORE OPERATING OPENER.

TO AVOID DAMAGE TO GARAGE DOOR AND OPENER, MAKE DOOR LOCKS INOPERATIVE BEFORE CONNECTING ELECTRIC POWER. USE A WOOD SCREW OR NAIL TO HOLD THE LOCKS IN "OPEN"

(UNLOCKED) POSITION.

INSTALLATION & WIRING MUST BE IN COMPLIANCE WITH LOCAL ELECTRICAL AND BUILDING CODES.

OPERATION AT OTHER THAN 120V 60Hz WILL CAUSE OPENER MALFUNCTION AND DAMAGE.

Opener MUST be permanently wired or plugged into a grounded 3-prong receptacle wired according to local elec-

trical codes. DO NOT use a 2.wire adapter. DO NOT use an extension cord.

PERMANENT WIRING

CONNECTION

(If required by local code.)

GroundTab

S_v

Green Wire

RIGHTWRONG

IF LOCAL CODES REQUIRE PERMANENT WIRING:

DISCONNECT POWER AT THE FUSE BOX BEFORE PROCEEDING.

PROCEDURE: Refer to illustration. Make connection through the 7/8" diameter hole in top of opener chassis.

1.Remove opener chassis cover by removing the cover screws.

2.Remove attached 3-prong cord.

3.Connect the black (line) wire to black wire on terminal block; white (neutral) wire to the white terminal wire; the green (ground) wire to green ground screw.

White

Wire

CAUTION: BE SURE THE UNIT IS GROUNDED ACCORDING TO LOCAL CODE.

IMPORTANT NOTE: TO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN OPENER NOW.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Contents Model 139.53626SR I/2HP Model 139.53515SR I/2HPMake Needed Adjustments Do not Wear RINGS, Watches or Loose Safety Reverse System Test is VeryAttempt Loosen Move or Adjust EEP GarageCare of the Opener Accessories Features of Your OpenerSpecifications Assembly Hardware Installation Youll Need ToolsCablepulleybracket AttachestoFRONT ENDofteerail AssemblyAssemble Tee Rail & Attach Cable Pulley Bracket CarefullyLockWasher Slide trolley assembly along rail to screwdriver stopAttach Tee Rail To Opener Chassis LodAttach Sprocket Cover to Chassis Install Chain and CableRemove Screwdriver Step Tighten the Chain and CableInstallation Sectional Door Piece Door with Track InstallationInstallation Piece Door Without Track ExampleAttach Tee Rail to Header Bracket Installation Sectional & ONE-PIECE Door with TrackInstallation ONE-PIECE Door With no Track Position Opener ChassisAttach Emergency Release Rope & Handle 16LockWasher 5/16-18NutWiring Instructions for Accessories Lock FeatureLight Feature Operation of Wall Control Wall Controlpush BARInstalling Lens Install Lights and LensesConnect Electric Power Permanent Wiring ConnectionDoor--HeaderWall Bracket OnepiecedoorLine Adjustment Procedures Sectional Door InstallationONE-PIECE Door Installation Connect Door Arm to TrolleyLimit Adjustment Chart AdjustmentAdjust UP and Down Limits Force Adjustment ChartOptional Instafl Infrared Reversing Sensor Test Safety Reverse SystemRepeat Adjustment After MATCH/CHANGE the Code in Transmitters SET Code Switches in ALL Transmitters to Matching PositionsSeries with Receiver Code Switches SET Receiver to MatchSituation Having a Problem?Probable Cause & Solution Door Wont CloseDo not Turn on Unit Must be GroundedKEY Part Repair PartsInstallation Parts List DescriptionNot Shown DriveWire Gear Contact Contact WireKEY Part NO. NO. Description Oown139.53626SR Sears WarrantyHOW to Order Repair Parts

139.53626SR - I/2HP, 139.53515SR - I/2HP specifications

The Craftsman 139.53626SR and 139.53515SR are two remarkable garage door openers that deliver reliable performance and advanced features ideal for both residential and commercial applications. Both models are powered by a robust ½ horsepower motor, providing a strong lift capability that can handle various types of garage doors.

One of the main features of the Craftsman 139.53626SR is its quiet operation. Designed with a belt drive system, it minimizes noise while delivering consistent performance. This makes it an excellent choice for homes where the garage is attached to the living space. The unit is also equipped with a soft-start and soft-stop feature, which ensures gentle movement of the door, further reducing noise and extending the lifespan of the garage door system.

The Craftsman 139.53515SR, on the other hand, incorporates a chain drive mechanism which is known for its durability and strength. This model is perfect for heavier doors or commercial applications where durability is crucial. It is built to withstand the rigors of frequent use and features a robust frame designed for long-lasting performance.

Both models include advanced safety features such as the infrared safety sensors that prevent the door from closing if something is detected in its path, thereby reducing the risk of accidents. They also come with a multi-function wall console, allowing for easy operation and access to settings like the vacation lock and door light control.

In terms of technology, the Craftsman openers are equipped with a security code system that changes the access code each time the remote is used. This feature enhances security by minimizing the risk of unauthorized access. Furthermore, both models are compatible with smartphone control options when paired with additional Craftsman connectivity accessories, providing users with the convenience of operating their garage doors remotely.

Setting up the Craftsman 139.53626SR and 139.53515SR is straightforward, thanks to the included installation manuals and clear instructions. Both models are designed for easy installation, making them ideal for DIY enthusiasts.

Overall, whether you choose the 139.53626SR for its quiet performance or the rugged 139.53515SR for its strength, both Craftsman garage door openers deliver reliability, advanced features, and safety, making them excellent additions to any home or business.
Top Page Image Contents