9Switch List
SW |
| Supported | Function | OFF | ON | Remark |
| Channel | |||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
SW01 | 1 | Channel 1 | Use of input contact | No | Yes | Set whether to use the Channel 1 input. |
| 2 | Channel 2 | Use of input contact | No | Yes | Set whether to use the Channel 2 input. |
| 3 | Channel 3 | Use of input contact | No | Yes | Set whether to use the Channel 3 input. |
| 4 | Channel 4 | Use of input contact | No | Yes | Set whether to use the Channel 4 input. |
| 5 | Unused |
|
|
| Set to OFF |
| 6 | Unused |
|
|
| Set to OFF |
| 7 | Unused |
|
|
| Set to OFF |
| 8 | Unused |
|
|
| Set to OFF |
SW02 | 1 |
| Pulse weight value setting: |
| ||
|
| SC setting (*1): | OFF | OFF |
| |
|
| Channel 1 | × 0.1: | OFF | ON | Set 1 pulse of the meter connected to channel 1. |
|
| |||||
| 2 |
| × 1: | ON | OFF |
|
|
| × 10: | ON | ON |
| |
|
|
|
| |||
| 3 |
| Pulse weight value setting: |
| ||
|
| SC setting (*1): | OFF | OFF |
| |
|
| Channel 2 | × 0.1: | OFF | ON | Set 1 pulse of the meter connected to channel 2. |
|
| |||||
| 4 |
| × 1: | ON | OFF |
|
|
| × 10: | ON | ON |
| |
|
|
|
| |||
| 5 |
| Pulse weight value setting: |
| ||
|
| SC setting (*1): | OFF | OFF |
| |
|
| Channel 3 | × 0.1: | OFF | ON | Set 1 pulse of the meter connected to channel 3. |
|
| |||||
| 6 |
| × 1: | ON | OFF |
|
|
| × 10: | ON | ON |
| |
|
|
|
| |||
| 7 |
| Pulse weight value setting: |
| ||
|
| SC setting (*1): | OFF | OFF |
| |
|
| Channel 4 | × 0.1: | OFF | ON | Set 1 pulse of the meter connected to channel 4. |
|
| |||||
| 8 |
| × 1: | ON | OFF |
|
|
| × 10: | ON | ON |
| |
|
|
|
| |||
SW03 | 1 | Unused |
|
|
| Set to OFF |
| 2 | Unused |
|
|
| Set to OFF |
| 3 | Unused |
|
|
| Set to OFF |
| 4 | Unused |
|
|
| Set to OFF |
| 5 | Unused |
|
|
| Set to OFF |
| 6 | Unused |
|
|
| Set to OFF |
| 7 | Unused |
|
|
| Set to OFF |
| 8 | Unused |
|
|
| Set to OFF |
SW06 |
|
|
| (Address 10s) 0 to 9 (decimal) | An address from 01 to 50 can be set. | |
|
|
|
|
| Set an address that is not the same as that of | |
SW07 |
|
| (Address 1s) 0 to 9 (decimal) | |||
|
|
| another unit. | |||
SW08 |
|
|
|
|
| Only enabled during communication error status |
|
| Communication error status display (error code | Change the switch to ON once | display. | ||
| 1 | display) |
| * The communication error status display is | ||
|
| and then return it to OFF. | ||||
|
| Temporary mask setting | masked for 10 seconds and the contact input | |||
|
|
|
| |||
|
|
|
|
|
| status is displayed. |
| 2 | Unused |
|
|
| Set to OFF |
| 3 | Unused |
|
|
| Set to OFF |
| 4 | Unused |
|
|
| Set to OFF |
| 5 | Unused |
|
|
| Set to OFF |
| 6 | Unused |
|
|
| Set to OFF |
SW09 | 1 | Unused |
|
|
| Set to OFF |
| 2 | Unused |
|
|
| Set to OFF |
Set the dip switches for function selection according to the system to be used.
At the time of shipment, all dip switches are set to OFF and the
*1: When using a system controller
*2: The pulse unit of the
10