Dolby Laboratories CP65 manual Voltage Acceptable Setting Voltage Range Fuse Type

Page 10

2-2

Locate the power amplifiers away from the Cat. No. 240A optical preamplifier to avoid hum pickup problems.

STEP 4 Disconnect power from the existing cinema sound equipment.

STEP 5 Disconnect all cabling from the existing cinema sound processing system,

but do not disconnect the wiring from power amplifiers, etc.

STEP 6 Check that the CP65 voltage selector switch is set correctly for your mains voltage and that the correct fuses are installed. (The selector switch is located on the rear of the Cat. No. 259 Power Supply and can be seen through the backplane.)

DISCONNECT THE CP65 FROM POWER BEFORE YOU TURN THE SELECTOR SWITCH FROM ONE POSITION TO ANOTHER.

The CP65 accepts both 50 Hz and 60 Hz power. The mains voltages must fall within the following limits:

Voltage

Acceptable

 

 

Setting

Voltage Range

Fuse

Type

100 VAC

85-110 VAC

1.25 A

1/4" x 1-1/4" slow-blow

120 VAC

102-132 VAC

1.25 A

1/4" x 1-1/4" slow-blow

140 VAC

119-154 VAC

1.25 A

1/4" x 1-1/4" slow-blow

200 VAC

170-220 VAC

T 630 mA

5 x 20mm time lag

220 VAC

187-242 VAC

T 630 mA

5 x 20mm time lag

240 VAC

204-265 VAC

T 630 mA

5 x 20mm time lag

NOTE

Follow all local codes and regulations covering electrical wiring. It is recommended that conduit be used for wiring runs.

STEP 7 All signal connections (except those to automation connector J18 -- see the following step) are made by soldering the leads to fanning strips (solder tags) that are supplied with the CP65. The fanning strips with the soldered wiring are fastened in place at the terminal blocks shown on the wiring diagram.

STEP 8 If you plan to make use of the automation interface in the CP65, there are two methods you can follow.

If both remote switches and their accompanying indicators for format, mute, and local / remote fader control are required you should use the 25 way D type connector J18. If only remote switches are required connections can be made to TB1 using the fanning strips supplied with the CP65.

Image 10
Contents Model CP65 Cinema Processor Dolby Laboratories Inc Headquarters Table of Contents Section Reference Block Diagrams Introduction Page Section Equipment Required Smpte Buzz Track Stereo Optical Surround Level Cat. No Jiffy Test Film Cat. No 2 Listen . . . Film Cat. NoSection Initial SET-UP and Installation Voltage Acceptable Setting Voltage Range Fuse Type Next, check the jumpers in the following locations Cat. No , Power Supply Module Cat. No , B-Chain CardCat. No , Control Logic Card J2 NON-SYNCCP65 Backplane Standard CP65 or CP65ACP65-300 High Low Subwoofer subwoofer Output output These Modules are Necessary for Bypass Operation Reduction Module Slot Card Function Cat. NoTwo-channel Noise Channel DecoderContains a semi-regulated power supply with Voltage Setting Fuse Type InternationalIEC Notices HUM Problems Room lighting dimmer controls SCR-TYPEPage Section AN Overview of the Alignment Procedure Aligning the B-ChainPage Page Section Chain Alignment Preliminary Procedures Action IndicationLamp Voltage Optical Preamplifier Adjustments Chain Alignment Procedures Optical Preamplifier Adjustments 222 CAT. no Test Film Oscilloscope Traces Repeat CAT no Repeat 1 →Magnetic Preamplifier Adjustments Magnetic Alignment 100mV Section Chain Alignment Setting Room Equalization BypassLoudspeakers and Crossovers Amplifiers GeneralChain Alignment Procedures OffRepeat ActionChain Alignment Procedures Setting Room Equalization Do not adjust Paul Setting Room Equalization b. Adjusting L,C,R Gain 14 → 21 R 14 →Setting Mono Gain 79 dBCChain Alignment Procedures Subwoofer Alignment Cat. No 90 dBC 85 dBCFrom Step NoSelect format 04 Dolby Stereo A-Type Same AS 441Surround Equalization Alignment Cat. No Surround Equalization Alignment Cat. No Notes Cat. No 441Desired 88 dBC Bypass Thumbwheel Switch Adjustment of Surround DelayMsec Setting Chain Alignment Procedures Adjustment of Bypass Gain Xx dBCFrom Xx dBC -3 dB Yy dBCAdjustment of Non-sync Gain Press the format 60 non sync switchAuto Freq Adjustment of Mono Gain and Equalization Notes Repeat page 5-20 StepChain Alignment Procedures Final Checks Press the format 04 Dolby Stereo A-type switchSection Reference Diagrams Cat. No Dual Noise Reduction Module Inputs Cat. No Optical Bass Extension and Surround Equalizer Card Cat. No B-Chain Facilities Card Cat. No Power Supply Card Cat. No Transformer Module Inputs Cat. No Control Logic Card 15V +12B Cat. No +24V +15V+15M Appendix a Checking Phasing of Speakers Appendix B Effect of Changes in Slit Height on Slit Losses Operation Appendix C CP65M Mono InstructionsCat. No a Circuit Description Schematic Cat. No a Appendix D Backplane Connections List Terminal Block TB3Connector J18