Dolby Laboratories CP65 manual Cat. No , B-Chain Card, Cat. No , Power Supply Module

Page 12

2-6

Cat. No. 242, B-Chain Card

J1

Jumper

Holder

(for storage)

Mono low

frequency filter OFF

100mV

 

 

Magnetic Input

in

 

 

Sensitivity Setting

in 1V

 

 

 

 

 

 

Cut jumpers for

 

 

 

high sensivity

 

 

 

power amplifiers

J5

J6

J7

J8

Cat. No. 242

J1 Mono LF cut In/Out: selects optional low frequency cut when Mono (format 01) is selected. In some cases the extended low frequency reponse may appear to be out of balance with the restricted high frequency response needed for the correct reproduction of mono optical sound-tracks. Move J1 to the ON position to attenuate the low frequency response.

J5, J6, J7, J8 Output levels: Jumpers W5, W6, W7, and W8 are set at the factory for a power amplifier input sensitivity of between 90 mV and 1.23 V. If the power amplifiers used in the installation are very sensitive (10 mV to 100 mV input sensitivity), it may be necessary to cut these jumpers.

See page 4-21 for information on setting the magnetic input sensitivity. The setting in effect is indicated by the arrow shown above.

Cat. No. 249, Power Supply Module

 

BYPASS OUTPUT LEVEL RANGE

 

 

Low

 

 

Hi

J1

Cat. No. 249

Low

Hi

 

 

J1 Bypass output level Hi/Low: Set to the Low bypass output range initially. If increased bypass output gain is required, as determined during the bypass gain adjustment later in this manual the jumper should then be placed in the Hi position.

Image 12
Contents Model CP65 Cinema Processor Dolby Laboratories Inc Headquarters Table of Contents Section Reference Block Diagrams Introduction Page Section Equipment Required Smpte Buzz Track Stereo Optical Surround Level Cat. No Jiffy Test Film Cat. No 2 Listen . . . Film Cat. NoSection Initial SET-UP and Installation Voltage Acceptable Setting Voltage Range Fuse Type Next, check the jumpers in the following locations Cat. No , Power Supply Module Cat. No , B-Chain CardCat. No , Control Logic Card J2 NON-SYNCCP65 Backplane Standard CP65 or CP65ACP65-300 High Low Subwoofer subwoofer Output output These Modules are Necessary for Bypass Operation Slot Card Function Cat. No Two-channel NoiseReduction Module Channel DecoderContains a semi-regulated power supply with Voltage Setting Fuse Type InternationalIEC Notices HUM Problems Room lighting dimmer controls SCR-TYPEPage Section AN Overview of the Alignment Procedure Aligning the B-ChainPage Page Section Chain Alignment Preliminary Procedures Action IndicationLamp Voltage Optical Preamplifier Adjustments Chain Alignment Procedures Optical Preamplifier Adjustments 222 CAT. no Test Film Oscilloscope Traces Repeat CAT no Repeat 1 →Magnetic Preamplifier Adjustments Magnetic Alignment 100mV Section Chain Alignment Setting Room Equalization BypassLoudspeakers and Crossovers Amplifiers GeneralChain Alignment Procedures OffRepeat ActionChain Alignment Procedures Setting Room Equalization Do not adjust Paul Setting Room Equalization b. Adjusting L,C,R Gain 14 → 21 R 14 →Setting Mono Gain 79 dBCChain Alignment Procedures Subwoofer Alignment Cat. No 90 dBC 85 dBCFrom Step NoSelect format 04 Dolby Stereo A-Type Same AS 441Surround Equalization Alignment Cat. No Surround Equalization Alignment Cat. No Notes Cat. No 441Desired 88 dBC Bypass Adjustment of Surround Delay Thumbwheel SwitchMsec Setting Chain Alignment Procedures Adjustment of Bypass Gain Xx dBCFrom Xx dBC -3 dB Yy dBCAdjustment of Non-sync Gain Press the format 60 non sync switchAuto Freq Adjustment of Mono Gain and Equalization Notes Repeat page 5-20 StepChain Alignment Procedures Final Checks Press the format 04 Dolby Stereo A-type switchSection Reference Diagrams Cat. No Dual Noise Reduction Module Inputs Cat. No Optical Bass Extension and Surround Equalizer Card Cat. No B-Chain Facilities Card Cat. No Power Supply Card Cat. No Transformer Module Inputs Cat. No Control Logic Card Cat. No +24V +15V 15V +12B+15M Appendix a Checking Phasing of Speakers Appendix B Effect of Changes in Slit Height on Slit Losses Appendix C CP65M Mono Instructions OperationCat. No a Circuit Description Schematic Cat. No a Appendix D Backplane Connections List Terminal Block TB3Connector J18