Emerson 848T manual Ci = Li =

Page 69

Reference Manual

00809-0100-4697, Rev EA October 2011

Rosemount 848T

Special Conditions for Safe Use (x):

1.This apparatus must be installed in an enclosure which affords it a degree of protection of at least IP20. Non-metallic enclosures must have a surface resistance of less than 1Gohm. Light alloy or zirconium enclosures must be protected from impact and friction when installed.

2.The apparatus will not meet the 500V rms isolation test required by Clause 6.4.12 on EN 60079-11:2007. This must be taken into account when installing the apparatus.

NE ATEX TYPE ‘n’ APPROVAL

Certification Number: BASEFFA09ATEX0095X

ATEX Marking II 3 G

Ex nA nL IIC T5 (Tamb = –40 to 65 °C)

Table B-9. Baseefa Approved Entity Parameters

Power/Bus

Ui = 42.4 Vdc

Ci = 0

Li = 0

Sensor

Uo = 5 Vdc

Io = 2.5 mA Co = 1000 μF Lo = 1000 mH

Special Conditions for Safe Use (x):

1.Provisions shall be made, external to the apparatus to prevent the rated voltage (42.4 Vdc) from being exceeded by transient disturbances of more than 40%.

2.The ambient temperature range of use shall be the most restrictive of the apparatus, cable gland, or blanking plug.

NOTE:

NE is valid with S001 Input Type ONLY

N1 ATEX Type n

Certification Number: Baseefa09ATEX0095X

ATEX Marking II 3 G

Ex nL IIC T5 (Tamb = –40 to 65 °C)

Table B-10. Entity Parameters

Power/Bus

Ui = 42.4 Vdc Ci = 0

Li = 0

Sensor

Uo = 12.5 Vdc Io = 4.8 mA Po = 15 mW Co = 1.2 μF Lo = 1 H

B-5

Page 68 Page 70
Image 69
Page 68 Page 70
Contents 00809-0100-4697, Rev EA October Reference ManualPage Customer Central National Response Center International Rosemount 848T High Density Temperature Transmitter withPage Table of Contents Section Operation MaintenanceAppendix a TOC-2Section Introduction Safety MessagesProcess leaks could result in death or serious injury Electrical shock could cause death or serious injuryMaintenance of the Rosemount 848T Temperature Transmitter Fieldbus host or configuration toolOverview TransmitterService Support Rosemount 848T Safety Messages Mounting Section InstallationMounting to a Panel with a Junction Box Mounting to a DIN Rail Without an EnclosureAluminum/Plastic Junction Box Stainless Steel Junction Box Mounting to a 2-in. Pipe StandSpur Signal Wiring Devices 1 through WiringConnections Leads and terminalsRTD or Ohm Inputs Thermocouple or Millivolt InputsAnalog Inputs Power Supply ConnectorsOhm resistor in the loop when switched to the left Analog InputPower Supply Surges/TransientsConnections Grounding Shielded WireTransmitter Enclosure optional 848T Power Supply Sensor Wires Shield ground pointsMA loop Fieldbus busSimulate Enable SwitchesSwitch is not functional SecurityCommissioning Tag TaggingTransmitter Tag Sensor TagInstallation Using Cable GlandsUsing Conduit Entries Section Configuration Configuration Transmitter Configuration Custom Configuration MethodsStandard Rosemount 848T Typical Profiling Application Common Configurations for High Density ApplicationsFunction BlockMonitoring Application with a Single Selection Measuring Temperature Points IndividuallyMultiple Analog Input or Analog Input Block Configuration Block Configuration Resource BlockNumber Parameter Description 00809-0100-4697, Rev EA October Resource Block Parameters Saveconfigblocks SaveconfignowStartwithdefaults FailedenableModes Block ErrorsAutomatic Auto Block is processing its normal background memory checksAlarm Detection Out of Service OOSPlantWeb Alerts Status HandlingFailedmask 00809-0100-4697, Rev EA October Failure AlarmsMaintenance Alarms/Priority Alarm Advisory AlarmsAlarm Recommended Actions for PlantWeb Alerts Alarm Type Active Event Recommended ActionTransducer Blocks RESOURCE.HARDWAREREV,RESOURCE.RBSFTWRREVALL Transducer Block Channel Definitions Transducer Block ErrorsChannel Definitions for the 848T Channel DescriptionTransducer Block Alarm Detection 00809-0100-4697, Rev EA October Block/Transducer ErrorTransducer Block Modes Block outputs reflect the analog input measurementSENSOR2CONFIG SENSOR1CONFIGSENSOR3CONFIG SENSOR4CONFIGChanging the Sensor Configuration in the Transducer Block 11. Xderror Sub-Parameter Structure 12. Sensorconfig Sub-Parameter StructureTransducer Block Sub-Parameter Tables 14. Sensorcal Sub-Parameter Structure 13. Sensorstatus Sub-Parameter Structure15. Calstatus Structure 16. Transducer Status Sub-Parameter StructureStructure Dual Sensor Status TableStructure 20. Validation Config Sub-Parameter Structure Sensor Calibration in the Sensor Transducer BlockStructure Parameter Description Rosemount 848T Operation and Maintenance Foundation Fieldbus InformationFoundation Commissioning Addressing Restart with Defaults Hardware MaintenanceSensor Check Restart Processor cyclingTransducer Block Troubleshooting TroubleshootingSymptom Possible Cause Corrective Action Symptom Possible Causes Corrective ActionAppendix a Reference Data Functional SpecificationsAlarms Update TimeBackup Link Active Scheduler LAS Transient ProtectionPhysical Specifications Function Blocks Performance SpecificationsAccuracy for Differential Configurations Sensor Option Sensor Reference 3-Wire RTDsAccuracy Input RangesAnalog Sensors 4-20mA Sensor Option Alarm Levels AccuracyAmbient Temperature Effect Ambient Temperature Notes Examples Dimensional DrawingsRosemount 848T Top ViewStainless Steel Junction Box-Cable Gland option code JS2 Side View Front ViewFront View Side View Side View Stainless Steel Junction Box-Conduit Entry option code JS3Aluminum/Plastic Junction Box Styles JA and JP Mounting OptionsStainless Steel Junction Box Style JS Front View Side ViewOptions Ordering InformationSpecial Temperature Test Expanded Software Configuration StandardConduit Electrical Connector Standard Enclosure Options StandardRosemount 848T Appendix B Product Certificates Table B-2. Entity Parameters for Non Incendive Field WiringHazardous Locations Certificates North American ApprovalsPower/Bus Canadian Standards Association CSA Certifications European Approvals Power/Bus SensorAtex Certifications Special Conditions for Safe UseCi = Li = Rosemount 848T IECEx Certifications Special Conditions of Safe UseRosemount 848T China NEPSICertifications Parameters Terminals of power/loopJapanese Certifications Intrinsically Safe and NON-INCENDIVE Installations Installation Drawings Figure B-1. FM Intrinsic Safety/ Fisco 00809-0100-4697, Rev EA Rosemount 848T Figure B-2. CSA Intrinsic Safety/ Fisco Rosemount 848T Rosemount 848T Overview Function Blocks Appendix C Foundation fieldbus TechnologyOutput InputSnap Linkages StatusInstrument- Specific Function Blocks Alerts Device Descriptions Block OperationResource Blocks Transducer BlocksNetwork Communication Link Active Scheduler LASFieldbus Link MID x ST Data LAS ParametersAddressing Scheduled Transfers Backup LASPublisher/Subscriber Report DistributionUnscheduled Transfers ScheduleDevice Device Y Device Z Function Block Scheduling Analog Input AI Function Block Appendix D Function BlocksNumber Parameter Units Description OUTXdscale AlarmhysOutscale IooptsOUT mode in auto OUT mode in manFunctionalitySimulation 63% of ChangeFiltering Signal ConversionDirect IndirectConditions Indirect Square RootTable D-3. Alarm Priority Levels Manual ManValue of the block output OUT may be set manually Advanced Features Uncertain if in Manual modeBAD if Limited Uncertain if LimitedApplication Information AI Block TroubleshootingXdblock HIHILIMIT, LolimitTable D-4. Multiple Analog Input Function Block Parameters Multiple Analog Input MAI Function BlockCAPSTDDEV1 Simulate Figure D-4. Multiple Analog Input Function Block SchematicOption in Manual or Out of Service mode only Devices such as flowmetersTable D-5. Blockerr Conditions Block output OUT may be set manually MAI Block Troubleshooting Table D-6. Input Selector Function Block Parameters Input Selector Function BlockIN1 IN2 IN3 IN4 IN5 IN6 IN7 OUT OutrangeMingood SelecttypeSelected OpselectMode Logic Selection INn DISABLEnAlarm OUT FunctionalityOUT reflects the selected value Table D-8. Alarm Priority LevelsUse Uncertain as Good Block ExecutionIsel Block Troubleshooting Numerics IndexMaintalarms Troubleshooting Configuration Errors Modes AutomaticAlarm Detection Errors Modes AutomaticPage Pacific Private Limited Rosemount Inc

848T specifications

The Emerson 848T is a state-of-the-art temperature transmitter designed for accurate and reliable temperature measurement in various industrial applications. This device has gained recognition for its advanced features and robust performance, making it a popular choice among engineers and technicians in the field.

One of the key highlights of the Emerson 848T is its unique dual-channel capability, which allows it to seamlessly monitor two temperature sources simultaneously. This functionality is particularly beneficial in processes where multiple temperature points need to be assessed, optimizing efficiency and reducing the need for additional equipment. It supports various sensor types, including thermocouples, RTDs, and resistance temperature detectors, making it versatile for different applications.

The 848T is equipped with sophisticated digital processing technology, which enhances its accuracy and stability. It features a 24-bit analog-to-digital converter, ensuring precise measurement and minimizing drift over time. Moreover, the device boasts a wide operating temperature range, accommodating ambient conditions from -40°C to 85°C. This durability makes it suitable for harsh environments commonly encountered in industries such as oil and gas, pharmaceuticals, and power generation.

Another significant characteristic of the Emerson 848T is its configurable output options. Users can choose from a range of output signals, including 4-20 mA, which provides a standard interface for integration into existing control systems. Additionally, it offers a HART communication protocol, allowing for easy configuration, calibration, and diagnostics through a digital interface. This feature enhances the transmitter's usability, enabling operators to perform adjustments without direct access to the device.

The device is designed with user-friendliness in mind. Its intuitive setup procedure and robust graphical user interface simplify the commissioning process, ensuring that even those new to the technology can easily navigate the system. An integrated LCD display provides real-time readings and status information, facilitating monitoring at a glance.

In summary, the Emerson 848T temperature transmitter combines reliable performance, user-friendly design, and advanced digital technologies. Its dual-channel capability, wide sensor compatibility, and adjustable output options make it an essential tool for achieving precise temperature measurements in various industrial settings. With these compelling features, the Emerson 848T stands out as a leading choice for professionals seeking accuracy and efficiency in their temperature monitoring applications.
Top Page Image Contents