Wolf Ventilation Hood S Ta L L S U P P O Rt S Y S T E M, N N E C T D E C O R At I V E F L U E

Page 10

W O L F COOKTOP VENTILATION HOODS

ISLAND HOOD I N S TA L L AT I O N

E L E C T R I C A L R E Q U I R E M E N T S

The Wolf cooktop island hood requires a separate, grounded 110/120 V AC, 60 Hz power supply. The service should have its own 15 amp circuit breaker. Locate the electrical supply with a minimum of 6' (1.8) of 120 V AC power cable on the ceiling through the top of the hood.

You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service.

I N S TA L L S U P P O RT S Y S T E M

At the island hood installation location, install two-by-four or 3/4" (19) plywood cross framing between ceiling joists. Refer to the island hood mounting pattern dimensions below.

Finish the ceiling surface. Be sure to mark the location of the ceiling joists and cross framing.

Determine the desired orientation of the island hood. Note that the front designates the control side of the hood.

Secure the upper half of the support frame to the joists and cross framing with four screws provided with your hood. Make sure that the screws are driven into the center of the joists and framing for maximum strength. Ensure the correct orientation of the support frame.

Adjust the overall height of the support frame. Loosen and retighten the screws in the height adjustment slots as necessary. Refer to the illustration below.

IMPORTANT NOTE: The hood height is 111/4"

(286)from the support frame attachment point. The bottom of the hood must be 24" (610) minimum and 30" (762) maximum from the countertop.

C O N N E C T D E C O R AT I V E F L U E

Secure the upper telescopic chimney flue section to the upper support frame. Refer to the illustration below.

Temporarily hold the lower telescopic chimney flue section over the upper flue section.

TOP VIEW

61/2"713/16"

(165)(198)

61/2" (165)

107/8" (276)

FRONT OF HOOD

Island hood mounting patterns

Height

Front of

Adjustment

Support

Slots

Frame

Wide

 

Mounting

 

Flange

 

Support frame orientation

Upper Flue

Mounting Screws

 

Lower Flue

Connect upper telescopic flue

10

Image 10
Contents Installation Instructions Page Model Number Serial Number L F Cooktop Ventilation Hoods Installation I N S T R U C T I O N S Hood P L a C E M E N T L C U L AT E C H I M N E Y F L U E H E I G H TU N T I N G H a R D WA R E I N C L U D E D S TA L L D U C T W O R KS TA L L M O U N T I N G B R a C K E T S E C T R I C a L R E Q U I R E M E N T SS TA L L B a C K S P L a S H S TA L L T H E H O O DE C T R I C a L C O N N E C T I O N S N N E C T D U C T W O R KIsland hood installation S TA L L S U P P O RT S Y S T E M N N E C T D E C O R AT I V E F L U EU N T H O O D to S U P P O RT F R a M E Decorative Flue Support Nuts Frame Weld Screws on HoodWA L L S H I E L D S T E R N a L B L O W E R SM OT E B L O W E R S U E E X T E N S I O N ST E R N a L B L O W E R I N S TA L L AT I O N M OT E B L O W E R I N S TA L L AT I O NM OT E B L O W E R W I R I N G Troubles H O O T I N G YO U N E E D Service 7 5 7 0 0