Breville BKC600XL manual Storage, Empty the Water Tank, Machine is now ready for use

Page 25

BR9013 BKC600XL_IB_AMEND.qxp 11/10/07 21:43 Page 24

Care and cleaning continued

Troub

The Brewer will continue to operate even when the LCD screen indicates ‘DESCALE’.

Note

However, if you do not descale the Brewer soon after it is displayed, continued scale build-up could damage the Brewer. If this occurs, ‘DESCALE’ will begin to flash, alerting you to the potential damage to the Brewer if you do not descale immediately. Promptly follow these steps each time the LCD screen indicates ‘DESCALE’ to ensure the Brewer functions optimally.

1.Empty the Water Tank.

2.Pour 60 oz. of vinegar into the Water Tank, filling to just below the top edge of the clear viewing area.

3.Place a 12 oz. or larger ceramic cup (do not use a plastic cup) on the Drip Tray. The Drip Tray and Drip Tray Plate can be removed to accomodate taller mugs and travel mugs

4.Select the largest brew size (11.25 oz. serving)

by pressing the button on the control panel.

5.Run a cleansing brew without a K-Cup®(refer to Brewing Hot Water, page 15). Pour the contents of the cup into the sink.

6.Repeat the cleansing brew process until the Water Tank is empty, pouring the contents of the cup into the sink after each cycle. Remember to raise and lower the Safety Locking Arm between each cycle so the control panel buttons illuminate.

7.Let the Brewer stand for at least 4 hours while still on.

8.Rinse the Water Tank thoroughly and fill with fresh water.

9.Place a 12 oz. or larger ceramic cup (do not use a plastic cup) on the Drip Tray.

10.Run a cleansing brew without a K-Cup®(refer to Brewing Hot Water, page 15). Pour the contents of the cup into the sink.

11.Repeat the cleansing brew process until the Water Tank is empty, pouring the contents of the cup into the sink after each cycle. You may need to perform additional rinse cycles if you notice any residual taste. Remember to raise and lower the Safety Locking Arm between each cycle so the control panel buttons illuminate.

12.The machine is now ready for use.

If the LCD screen continues to indicate ‘DESCALE’ after completing the process, repeat the process above.

Note

Storage

Before cleaning or moving the Brewer to a different location, ensure the Brewer has been turned off. Switch off at the wall outlet, unplug the power cord and allow the machine to cool. The Water Tank should be emptied and dried thoroughly.

•Store your Brewer in its upright position to avoid water leakage from the inner tank.

•Store your Brewer in a frost free environment. Storing the Brewer in a cold environment runs the risk of water freezing inside the Brewer and causing damage. If your Brewer has been stored in an environment below freezing, ensure to let it warm to room temperature for at least 2 hours before using.

•When preparing to use the Brewer after storage, we recommend rinsing the Water Tank with fresh

water and running three cleansing brews without a K-Cup®(refer to Brewing Hot Water, page 15).

Possi

Brewer

Brewer

Coffee or wat

There a from 13 on K-Cu Custom www.br

24

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Breville Customer Service Center Gourmet Single Cup Brewer Contents Congratulations Breville recommends safety first Uctions Cord plug Not orRisk Tlet, it ion to 3-prong Know your Breville Gourmet Single Cup Brewer My K-Cuplid Your Brewer is ready for the one-time priming process Installing the water filterOne-time priming process WerDer To placeSelect a K-Cup Brewing a K-CupWing Omplete BrewOpen the storage compartment located on top For the next brew cycleInsert the Filter Basket into the Holder Level sOn top of the Brewer Holder. When closed completely, the LCD screenArrow on the My K-CupLid with Arrow in the Brewing Chamber Ground To go up in size or the button to go down in sizeBrewing hot water Stopping the brew processRefilling the water tank Aligning the arrow on the K-CupHolderDo not remove the Water Tank during the brewing process Purging the brewerSetting the ‘ON-OFF TIME’ feature Setting the ‘CLOCK SET’ featureYou must set the clock if using the ‘ON-OFF TIME’ feature Menu and programming optionsLCD screen will return to the menu programming options Follow the instructions ii to iv for Setting the ‘ON TIME’Ready to Etting Setting the ‘AUTO OFF’ FeatureSetting the ‘BREW SIZE’ feature Setting the ‘BREW TEMP’ featurePress the button to reach ‘BREW TEMP’ Over Will returnCleaning the brewer housing Care and cleaningCleaning the K-CupHolder Cleaning the My K-CupaccessoryCleaning the water filter Cleaning the water tank and lidDescaling the brewer Empty the Water Tank StorageMachine is now ready for use Exit Needle may be clogged refer Cleaning the K-CupHolder, TroubleshootingRepeat DifferentWarr One year limited warranty WarrantyOlder Scaling Mes Again
Top Page Image Contents