KitchenAid W10681447A manual Install Overlay Series Custom Panels, Door Panel Installation

Page 19

1.Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be off the floor.

A B

A

B

A. Rear leveling bolt

B. Front leveling bolt

2.Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

3.Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

A B

C

¹⁄₄" (6 mm) max.

2" (5 cm)

D

A. Center board ¹⁄₄" (6.35 mm) max. above refrigerator

B. 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards (2)

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than

50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.

4.For Overlay models, additional adjustments may be needed after the custom panels are installed.

Install Overlay Series Custom Panels

IMPORTANT:

■Install the custom handles prior to installing the panels on the refrigerator. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-442-9991. In Canada, visit www.KitchenAid.ca, or call 1-800-807-6777.

■Create custom door overlay panels according to the specifications in the “Overlay Series Custom Panels” section.

■KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panel Installation

1.Remove all tape and door bracing from the refrigerator and freezer doors.

2.Open the refrigerator and freezer compartment doors.

3.Remove the handle-side and top trims.

A

A

 

A.Trims

4.Slide the custom panels into the bottom and hinge side trims on the refrigerator compartment and freezer compartment doors, making sure that the backer panel fits into the hinge side trims.

AA

A. Panels

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresÍndice Table of ContentsTable DES Matières Your safety and the safety of others are very important Refrigerator SafetyArchitect Series ModelsSide by Side Non-Dispensing Refrigerators Side by Side Dispensing RefrigeratorsTools and Parts Installation RequirementsLocation Requirements Recommended Grounding Method Electrical RequirementsTipping Radius Water Supply RequirementsProduct Dimensions 48 121.9 cm Models Door Swing Dimensions36 91.4 cm Models 42 106.7 cm ModelsOverlay Series Door Panel and Cabinetry Clearance DoorHinge Decorative Overlay Panel Overlay Series Custom Panels and Handle KitsModel a Architect Series Custom Side Panels Overlay Series Custom Side Panels Inset Installation DimensionsFlush Installation Dimensions Recessed Inset Installation DimensionsMeasure the distance from point a as shown to back wall Installation InstructionsUnpack the Refrigerator Reduce Tipping RadiusMove the Refrigerator into House Install Anti-Tip BoardsConnect the Water Supply Connect to Refrigerator Parts SuppliedStyle 2-Copper Line Connection Place the end of the tubing into a bucket, and turn shutoffPlug in Refrigerator Move Refrigerator to Final LocationLevel and Align Refrigerator Door Panel Installation Install Overlay Series Custom PanelsClassic and Architect Models Adjust DoorsDoor Height Adjustment Door Swing AdjustmentInstall Base Grille Install Side PanelDoor-to-Door or Door-to-Refrigerator Trim Adjustment Style 2 Non-Dispenser Models Complete InstallationWater System Preparation Style 1 Dispenser ModelsSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorSerie Architect ModelosRefrigeradores de dos puertas sin despachador Refrigeradores de dos puertas con despachadorHerramientas necesarias Requisitos DE InstalaciónHerramientas y piezas Requisitos de ubicaciónRequisitos eléctricos Medidas de la aberturaSe debe mantener un espacio de ½ 1,3 cm por encima Para su modelo. Para obtener más información, veaPresión del agua Requisitos eléctricosRequisitos del suministro de agua Método de conexión a tierra recomendadoMedidas del producto Arco de vuelcoMedidas de oscilación de las puertas Panel Oscilación de Modelo a Panel decorativo recubiertoSerie Architect Agarraderas Pieza n Color Paneles laterales a la medida para Las series ArchitectPaneles de soporte Modelo DMedidas para la instalación empotrada RefrigeradorAdorno lateral Medidas para la instalación en relieveModelo Arco de vuelco reducido Instrucciones DE InstalaciónDesempaque el refrigerador Cómo reducir el arco de vuelcoCómo instalar los tableros antivuelco Cómo hacer entrar el refrigerador En la casaCómo instalar los tableros antivuelco Estilo 2-Conexión de la tubería de cobre Conexión del suministro de aguaConexión a la línea de agua Piezas necesarias Estilo 1-Conexión de la válvula de cierreConexión al refrigerador Piezas suministradas Cómo enchufar el refrigeradorNivelación y alineamiento del refrigerador Cómo mover el refrigerador a su Ubicación finalModelos Classic y Architect Ajuste las puertasInstalación del panel de la puerta Cómo ajustar la altura de la puertaModelos de paneles recubiertos Cómo ajustar la oscilación de las puertasCómo instalar la rejilla de la base Cómo instalar el panel lateralEncaje a presión el faldón sobre la rejilla de la base Estilo 2 Modelos sin despachador Cómo terminar la instalaciónPreparación del sistema de agua Estilo 1 Modelos con despachadorVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurSérie Architect ModèlesRéfrigérateurs côte à côte sans distributeur Réfrigérateurs côte à côte avec distributeurOutillage requis Exigences D’INSTALLATIONExigences d’emplacement Outillage et piècesDimensions de l’ouverture Pression de l’eau Méthode recommandée de mise à la terreSpécifications électriques Spécifications de l’alimentation en eauRayon de basculement Dimensions du produitModèles de 48 121,9 cm Dimensions pour louverture des portesVue avant Modèles de 36 91,4 cm Modèles de 42 106,7 cmPorte Porte Modèle a Panneau décoratif de la série Panneaux décoratifsPanneaux latéraux personnalisés Des séries Architect Réfrigérateur Dimensions d’installation pour un panneau inséré en retraitDimensions d’installation pour un panneau inséré Dimensions d’installation pour un panneau en affleurementDéballage du réfrigérateur Instructions ’INSTALLATIONModèle Rayon de basculement réduit Installation de planches antibasculementRéduction du rayon de basculement Faire entrer le réfrigérateur Dans le domicileStyle 1-Raccordement au robinet d’arrêt Installation des planches antibasculementRaccordement à l’alimentation en eau Raccordement à la canalisation d’eau Pièces nécessairesBrancher sur une prise à 3 alvéoles reliée à la terre Branchement du réfrigérateurRaccordement au réfrigérateur Pièces fournies La caisse à la position OFF arrêtRéglage de l’aplomb et alignement Du réfrigérateur Déplacement du réfrigérateur à Lemplacement finalModèles Classic et Architect Installation des panneaux de porteAjustement des portes Ajustement de la hauteur des portesModèles Panneaux décoratifs Ajustement de l’ouverture des portesInstallation de la grille de la base Installation du panneau latéralEmboîter la plinthe sur la grille de la base Style 2 Modèles sans distributeur Achever l’installationPréparation du système d’eau Style 1 Modèles avec distributeur

W10681447A specifications

The KitchenAid W10681447A is a versatile and highly efficient dishwasher designed to meet the demands of modern kitchens. Renowned for its superior cleaning capabilities, this appliance brings together cutting-edge technology, thoughtful design, and an array of features tailored to enhance the user experience.

One of the standout features of the W10681447A is its advanced cleaning system. Equipped with a powerful wash system that utilizes a combination of spray patterns and high-pressure jets, this dishwasher ensures that even the toughest dirt and grease are effectively removed. The soil sensor technology automatically adjusts the wash cycle based on the level of dirt detected, ensuring optimal cleaning performance every time.

Another key characteristic is the adjustable upper rack that provides added flexibility when loading dishes. This feature allows users to accommodate taller items in both the lower and upper racks, maximizing the dishwasher's capacity. The dishwasher also boasts a third-level rack, providing extra space for utensils and small items, which ensures that every inch of the appliance is utilized efficiently.

The W10681447A emphasizes quiet operation, featuring a sound-dampening system that includes a motor sound insulation blanket and sound-reducing materials. With a noise level of just 47 dBA, it is one of the quietest models on the market, allowing you to run it anytime without disturbing your household.

In terms of energy efficiency, the KitchenAid W10681447A is designed to minimize water and energy usage without compromising on performance. It is ENERGY STAR certified, which means it meets strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. This not only benefits the environment but also saves users on utility bills.

The dishwasher comes with a variety of wash cycles and options, including heavy, normal, and quick wash cycles, as well as specialized settings for pots and pans. Additionally, it features a Delay Start option, allowing users to schedule the washing cycle at their convenience.

Overall, the KitchenAid W10681447A exemplifies excellence in design and functionality. With its powerful performance, innovative features, and quiet operation, it is an ideal choice for homeowners seeking a dependable and efficient dishwasher that can handle the rigors of everyday cooking and entertaining.
Top Page Image Contents