KitchenAid W10681447A manual Install Side Panel, Install Base Grille

Page 21

Door-to-Door or Door-to-Refrigerator Trim Adjustment

1.Loosen, but do not remove, the four Torx®† 27 flat-head mounting screws and the two ¹⁄₄" hex-head mounting screws.

2.Adjust the top hinge of either door to align it with the other door or the refrigerator trim.

3.Tighten the four Torx®† 27 flat-head mounting screws to a torque of approximately 100 inch-pounds (11.3 Nm) and tighten the two ¹⁄₄" hex-head mounting screws.

A

B

A. Torx® 27 flat-head mounting screws

B. ¹⁄₄" hex-head mounting screws

Install Side Panel

If the built-in area depth is 25" (63.5 cm) or more, the side panels can be installed inside the side trim or attached to the outside of the side trim.

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

1.For the inside side trim piece, slide the front edge of the routed side panel into the trim piece.

2.Nail the rear edge of the panel to the support board.

A

B

A. Support board (mounted to back wall)

B. Cab side trim

†®TORX is a registered trademark of Saturn Fasteners, Inc.

Install Base Grille

There are two pieces to the base grille to allow for a custom fit: the base grille itself and the skirt. The skirt can be added to the base grille in order to extend it all the way to the floor.

1.To see whether the skirt is needed, place the base grille into position. Do not attach the base grille to the refrigerator. Measure the distance between the bottom of the base grille and the floor. The gap must be a minimum of ¹⁄₂" (1.27 cm) in order to add the skirt.

NOTE: If the gap measures less than ¹⁄₂" (1.27 cm), skip steps 3 and 4 of the instructions, and install the base grille only.

2.Remove the film from the base grille.

3.Snap the skirt onto the base grille.

A

B

A. Base grille

B.Skirt

4.Trim the skirt by scoring the proper “V” groove with a utility knife. Break the skirt at the score line.

A

A. “V” groove

5.Using the two screws, attach the base grille assembly to the refrigerator as shown.

NOTE: Drive in the right side screw first.

A

A. Screws (2)

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable of Contents ÍndiceTable DES Matières Your safety and the safety of others are very important Refrigerator SafetySide by Side Non-Dispensing Refrigerators ModelsSide by Side Dispensing Refrigerators Architect SeriesInstallation Requirements Tools and PartsLocation Requirements Recommended Grounding Method Electrical RequirementsTipping Radius Water Supply RequirementsProduct Dimensions 36 91.4 cm Models Door Swing Dimensions42 106.7 cm Models 48 121.9 cm ModelsOverlay Series Door Panel and Cabinetry Clearance DoorHinge Overlay Series Custom Panels and Handle Kits Decorative Overlay PanelModel a Architect Series Custom Side Panels Flush Installation Dimensions Inset Installation DimensionsRecessed Inset Installation Dimensions Overlay Series Custom Side PanelsUnpack the Refrigerator Installation InstructionsReduce Tipping Radius Measure the distance from point a as shown to back wallInstall Anti-Tip Boards Move the Refrigerator into HouseConnect the Water Supply Style 2-Copper Line Connection Parts SuppliedPlace the end of the tubing into a bucket, and turn shutoff Connect to RefrigeratorMove Refrigerator to Final Location Plug in RefrigeratorLevel and Align Refrigerator Door Panel Installation Install Overlay Series Custom PanelsDoor Height Adjustment Adjust DoorsDoor Swing Adjustment Classic and Architect ModelsInstall Side Panel Install Base GrilleDoor-to-Door or Door-to-Refrigerator Trim Adjustment Water System Preparation Complete InstallationStyle 1 Dispenser Models Style 2 Non-Dispenser ModelsSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorRefrigeradores de dos puertas sin despachador ModelosRefrigeradores de dos puertas con despachador Serie ArchitectHerramientas y piezas Requisitos DE InstalaciónRequisitos de ubicación Herramientas necesariasSe debe mantener un espacio de ½ 1,3 cm por encima Medidas de la aberturaPara su modelo. Para obtener más información, vea Requisitos eléctricosRequisitos del suministro de agua Requisitos eléctricosMétodo de conexión a tierra recomendado Presión del aguaMedidas del producto Arco de vuelcoMedidas de oscilación de las puertas Panel Oscilación de Modelo a Panel decorativo recubiertoPaneles de soporte Paneles laterales a la medida para Las series ArchitectModelo D Serie Architect Agarraderas Pieza n ColorAdorno lateral RefrigeradorMedidas para la instalación en relieve Medidas para la instalación empotradaDesempaque el refrigerador Instrucciones DE InstalaciónCómo reducir el arco de vuelco Modelo Arco de vuelco reducidoCómo hacer entrar el refrigerador En la casa Cómo instalar los tableros antivuelcoCómo instalar los tableros antivuelco Conexión a la línea de agua Piezas necesarias Conexión del suministro de aguaEstilo 1-Conexión de la válvula de cierre Estilo 2-Conexión de la tubería de cobreConexión al refrigerador Piezas suministradas Cómo enchufar el refrigeradorNivelación y alineamiento del refrigerador Cómo mover el refrigerador a su Ubicación finalInstalación del panel de la puerta Ajuste las puertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectModelos de paneles recubiertos Cómo ajustar la oscilación de las puertasCómo instalar el panel lateral Cómo instalar la rejilla de la baseEncaje a presión el faldón sobre la rejilla de la base Preparación del sistema de agua Cómo terminar la instalaciónEstilo 1 Modelos con despachador Estilo 2 Modelos sin despachadorVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurRéfrigérateurs côte à côte sans distributeur ModèlesRéfrigérateurs côte à côte avec distributeur Série ArchitectExigences d’emplacement Exigences D’INSTALLATIONOutillage et pièces Outillage requisDimensions de l’ouverture Spécifications électriques Méthode recommandée de mise à la terreSpécifications de l’alimentation en eau Pression de l’eauRayon de basculement Dimensions du produitVue avant Modèles de 36 91,4 cm Dimensions pour louverture des portesModèles de 42 106,7 cm Modèles de 48 121,9 cmPorte Porte Modèle a Panneau décoratif de la série Panneaux décoratifsPanneaux latéraux personnalisés Des séries Architect Dimensions d’installation pour un panneau inséré Dimensions d’installation pour un panneau inséré en retraitDimensions d’installation pour un panneau en affleurement RéfrigérateurDéballage du réfrigérateur Instructions ’INSTALLATIONRéduction du rayon de basculement Installation de planches antibasculementFaire entrer le réfrigérateur Dans le domicile Modèle Rayon de basculement réduitRaccordement à l’alimentation en eau Installation des planches antibasculementRaccordement à la canalisation d’eau Pièces nécessaires Style 1-Raccordement au robinet d’arrêtRaccordement au réfrigérateur Pièces fournies Branchement du réfrigérateurLa caisse à la position OFF arrêt Brancher sur une prise à 3 alvéoles reliée à la terreRéglage de l’aplomb et alignement Du réfrigérateur Déplacement du réfrigérateur à Lemplacement finalAjustement des portes Installation des panneaux de porteAjustement de la hauteur des portes Modèles Classic et ArchitectModèles Panneaux décoratifs Ajustement de l’ouverture des portesInstallation du panneau latéral Installation de la grille de la baseEmboîter la plinthe sur la grille de la base Préparation du système d’eau Achever l’installationStyle 1 Modèles avec distributeur Style 2 Modèles sans distributeur

W10681447A specifications

The KitchenAid W10681447A is a versatile and highly efficient dishwasher designed to meet the demands of modern kitchens. Renowned for its superior cleaning capabilities, this appliance brings together cutting-edge technology, thoughtful design, and an array of features tailored to enhance the user experience.

One of the standout features of the W10681447A is its advanced cleaning system. Equipped with a powerful wash system that utilizes a combination of spray patterns and high-pressure jets, this dishwasher ensures that even the toughest dirt and grease are effectively removed. The soil sensor technology automatically adjusts the wash cycle based on the level of dirt detected, ensuring optimal cleaning performance every time.

Another key characteristic is the adjustable upper rack that provides added flexibility when loading dishes. This feature allows users to accommodate taller items in both the lower and upper racks, maximizing the dishwasher's capacity. The dishwasher also boasts a third-level rack, providing extra space for utensils and small items, which ensures that every inch of the appliance is utilized efficiently.

The W10681447A emphasizes quiet operation, featuring a sound-dampening system that includes a motor sound insulation blanket and sound-reducing materials. With a noise level of just 47 dBA, it is one of the quietest models on the market, allowing you to run it anytime without disturbing your household.

In terms of energy efficiency, the KitchenAid W10681447A is designed to minimize water and energy usage without compromising on performance. It is ENERGY STAR certified, which means it meets strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. This not only benefits the environment but also saves users on utility bills.

The dishwasher comes with a variety of wash cycles and options, including heavy, normal, and quick wash cycles, as well as specialized settings for pots and pans. Additionally, it features a Delay Start option, allowing users to schedule the washing cycle at their convenience.

Overall, the KitchenAid W10681447A exemplifies excellence in design and functionality. With its powerful performance, innovative features, and quiet operation, it is an ideal choice for homeowners seeking a dependable and efficient dishwasher that can handle the rigors of everyday cooking and entertaining.
Top Page Image Contents