Clarion APX1000.2 manual High-pass/Low-pass Filter Controls

Page 4

•Gain Control - This allows you to set the nominal operating level of the amplifier. The amplifier’s range, 250mV to 2.5V for RCA inputs, can accommodate input levels from virtually any brand of source unit.

•Bass Boost Control- The amplifier also features a “high-Q” (i.e. narrow frequency band) Bass Boost circuit. It acts much like an equlaizer, with adjustable gain (from 0 to +18dB) fixed at 45Hz. Use this feature to tune low- frequency audio response to compensate for a less than ideal subwoofer enclosure design. The added boost produces rich, full bass tones that are normally difficult to reproduce in the car audio environment. NOTE: If Bass Boost is undesired, set Bass Boost to 0dB.

•Pass Through - This allows you to “daisy chain” multiple amplifiers by internally splitting off the RCAinput to the Pass Through output. (The Pass Through output signal will be identical to the input signal. For example, full range in equals full range out, 50Hz low-pass in equals 50Hz low-pass out.)

•Power Save - When engaged, the amplifier will automatically minimize the current drawn while the amplifier is idle or the system volume is at a low level. This feature increases your amplifier’s efficiency by not drawing unnecessary current.

High-pass/Low-pass Filter Controls

•Frequency (Hz) Selection Control - The crossover frequency is fully adjustable between 50Hz and 5500Hz (via the Crossover Frequency Multiplier) for a wide range of crossover points. Use this feature, along with your speaker manufacturer’s recommended crossover frequencies, to quickly design a more advanced system (see Applications on page 5.) NOTE: If the X-Over Mode Switch is set to FULL, varying the Freq (Hz) Control will produce no effect.

•Crossover Frequency Multiplier Switch - When engaged, this switch increases the crossover frequency by a factor of 10. Example: If the Freq (Hz) dial is set for 240 Hz, pushing in the multiplier Switch changes the setting to 2400 Hz.

•X-Over Mode Switch - This switch is equipped with a selectable 12 or 24dB per octave electronic filter for precise frequency attenuation with minimal phase distortion. The steep crossover slope keeps midrange tones out of the subwoofer and thereby eliminates an unnatural “nasal” tone quality in the audio system. A filter is activated by sliding the X-Over Mode Switch to either LP or HP.

•Input Mode Switch - This switch allows you to set the input mode. Stereo input allows full left and right stereo operation. Right (bridged) input allows single channel input for bridged operation. This is especially useful in high- powered systems when using one amplifier for each subwoofer/speaker. L + R (sum mono) allows a stereo input to be summed into a mono output.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Page Table of Contents About the Manual and WarrantyIntroduction Description Input Connections and Audio ControlsHigh-pass/Low-pass Filter Controls Connections for Power and Speakers Applications Channel Full-Range, Satellite, or Subwoofer Stereo System Mixed-Mode Satellite and Subwoofer System Mounting Precautions InstallationWiring Precautions Page Electrical connections for the APX1000.2 Setting the Crossover Setting the GainSetting the Bass Boost Troubleshooting Final System ChecksProduct Specs APX1000.2Page APX1000.0-10 Rev.1 04/00

APX1000.2 specifications

The Clarion APX1000.2 is a powerful and versatile amplifier designed for car audio enthusiasts seeking an upgrade to their sound system. With its robust performance and high-quality features, the APX1000.2 is built to deliver unprecedented audio experiences.

One of the standout features of the APX1000.2 is its impressive output power. This amplifier can deliver up to 1000 watts of peak power, allowing it to drive subwoofers and speakers with ease. The two-channel setup provides flexibility for various configurations, making it suitable for mono, stereo, or multi-channel setups. This versatility caters to a wide range of users, whether they are looking to amplify their entire sound system or focus on enhancing bass performance.

Technology-wise, the APX1000.2 incorporates advanced Class D amplification, known for its efficiency and high power output. Class D amplifiers are designed to produce high levels of power while minimizing heat generation, which is essential for maintaining optimal performance during long listening sessions. This makes the APX1000.2 ideal for users who enjoy loud music without the risk of overheating.

In terms of sound quality, the APX1000.2 features a wide frequency response range and low distortion levels. This means that irrespective of the music genre, the amplifier reproduces audio accurately across the spectrum, from deep bass to crisp highs. Additionally, the built-in crossover allows users to tailor their sound preferences, ensuring that frequencies are appropriately distributed between speakers and subwoofers.

Installation flexibility is another key characteristic of the Clarion APX1000.2. It is designed with a compact form factor, making it easier to fit into various vehicle setups without compromising on space or performance. The amplifier also comes with a range of ports and connections, allowing for straightforward integration with existing audio systems.

Lastly, the APX1000.2 is equipped with various protection features, including thermal and overload protection, ensuring that the unit operates safely under demanding conditions. This attention to reliability contributes to the overall value of the amplifier, as users can trust it to perform consistently.

In conclusion, the Clarion APX1000.2 stands out as a powerful, efficient, and flexible amplifier suitable for any audio enthusiast looking to elevate their in-car listening experience. With its combination of cutting-edge technology, impressive power output, and superior sound quality, it is a worthy investment for anyone passionate about music on the road.
Top Page Image Contents