Clarion APX1000.2 manual

Page 10

5.Add an external fuse on the amplifier’s positive (+) power lead and connect it as close as possible to the vehicle’s (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external fuse will protect the electrical system from short circuits that can cause a fire.

6.Refer to Figure 6 when making electrical connections. Connect the amplifier’s positive (+) lead via a fuse directly to the positive (+) terminal on the battery. Do not connect this wire to the car’s fuse panel. Use red-insulated 10-gauge (or larger) wire for the amplifier’s positive (+) power lead and the same-gauge black-insulated wire for the ground.

7.When replacing the amplifier’s fuse, always use one having the same current rating. Substituting a higher-rated fuse or a slow-blow type can result in serious damage to the amplifier.

8.Never ground the speakers to the vehicle chassis or body.

9.Make sure that your vehicle’s electrical system (alternator, battery, etc.) is capable of handling the additional load. If you are planning a multi-amplifier system, you may need to add a second battery and possibly upgrade the alternator with a higher-output rated model. Consult your authorized Clarion dealer for recommendations.

10.To avoid noise problems, run the amplifier’s positive (+) power lead along one side of the vehicle to the battery. Run the remote turn-on wire and RCA audio cables down the center, and route the speaker wires along the remaining side. If wires must cross, run them perpendicular to each other.

11.When creating passage holes for the power wire, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being nicked and causing a short circuit.

12.Extra cable can cause signal loss and act as an “antenna” for noise. Use only high-quality RCA cables that are no longer than necessary to make a direct connection with the source unit or equalizer.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page Table of Contents About the Manual and WarrantyIntroduction Description Input Connections and Audio ControlsHigh-pass/Low-pass Filter Controls Connections for Power and Speakers Applications Channel Full-Range, Satellite, or Subwoofer Stereo System Mixed-Mode Satellite and Subwoofer System Mounting Precautions InstallationWiring Precautions Page Electrical connections for the APX1000.2 Setting the Crossover Setting the GainSetting the Bass Boost Troubleshooting Final System ChecksProduct Specs APX1000.2Page APX1000.0-10 Rev.1 04/00

APX1000.2 specifications

The Clarion APX1000.2 is a powerful and versatile amplifier designed for car audio enthusiasts seeking an upgrade to their sound system. With its robust performance and high-quality features, the APX1000.2 is built to deliver unprecedented audio experiences.

One of the standout features of the APX1000.2 is its impressive output power. This amplifier can deliver up to 1000 watts of peak power, allowing it to drive subwoofers and speakers with ease. The two-channel setup provides flexibility for various configurations, making it suitable for mono, stereo, or multi-channel setups. This versatility caters to a wide range of users, whether they are looking to amplify their entire sound system or focus on enhancing bass performance.

Technology-wise, the APX1000.2 incorporates advanced Class D amplification, known for its efficiency and high power output. Class D amplifiers are designed to produce high levels of power while minimizing heat generation, which is essential for maintaining optimal performance during long listening sessions. This makes the APX1000.2 ideal for users who enjoy loud music without the risk of overheating.

In terms of sound quality, the APX1000.2 features a wide frequency response range and low distortion levels. This means that irrespective of the music genre, the amplifier reproduces audio accurately across the spectrum, from deep bass to crisp highs. Additionally, the built-in crossover allows users to tailor their sound preferences, ensuring that frequencies are appropriately distributed between speakers and subwoofers.

Installation flexibility is another key characteristic of the Clarion APX1000.2. It is designed with a compact form factor, making it easier to fit into various vehicle setups without compromising on space or performance. The amplifier also comes with a range of ports and connections, allowing for straightforward integration with existing audio systems.

Lastly, the APX1000.2 is equipped with various protection features, including thermal and overload protection, ensuring that the unit operates safely under demanding conditions. This attention to reliability contributes to the overall value of the amplifier, as users can trust it to perform consistently.

In conclusion, the Clarion APX1000.2 stands out as a powerful, efficient, and flexible amplifier suitable for any audio enthusiast looking to elevate their in-car listening experience. With its combination of cutting-edge technology, impressive power output, and superior sound quality, it is a worthy investment for anyone passionate about music on the road.
Top Page Image Contents