KitchenAid W10029780 installation instructions Electrical Requirements

Page 6

Venting Methods

This canopy range hood is factory set for venting through the roof or wall.

A 6" (15.2 cm) round vent system is needed for installation (not included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance.

Vent system can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.

Rear discharge

A 90° elbow may be installed immediately above the hood.

For non-vented (recirculating) installations

If it is not possible to vent cooking fumes and vapors to the outside, the hood can be used in the non-vented (recirculating) version, fitting an activated carbon filter and the deflector. Fumes and vapors are recycled through the top grille.

Roof Venting

Wall Venting

Non-vented

 

 

(recirculating)

 

A

A

 

 

B

 

B

B

A

A. Roof cap

A. Wall cap

A. Deflector

B. 6" (15.2 cm)

B. 6" (15.2 cm)

B. 6" (15.2 cm)

round vent

round vent

round vent

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent Piece

6" (15.2 cm) Round

45° elbow

2.5 ft

 

(0.8 m)

90° elbow

5.0 ft

 

(1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system

90 elbow

 

 

 

 

 

 

Wall cap

 

 

6 ft (1.8 m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2ft

(0.6 m)

The following example falls within the maximum recommended vent length of 35 ft (10.7 m).

1

- 90° elbow

= 5.0 ft (1.5 m)

1

- wall cap

= 0.0 ft (0.0 m)

8 ft (2.4 m) straight

= 8.0 ft (2.4 m)

 

 

Length of system

= 13.0 ft (3.9 m)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

If the house has aluminum wiring follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the hood.

Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

6

Image 6
Contents Canopy Range Hood Range Hood Safety Table DES MatièresImportant Safety Instructions Installation Requirements ToolsandPartsLocation Requirements VentingRequirements Installation DimensionsCold weather installations Makeup airElectrical Requirements Chimney Support Bracket Installation Installation InstructionsRange Hood Mounting Screws Installation PrepareLocationNon-vented recirculating Installations InstallRange HoodVented Installations Complete PreparationInstall Upper Chimney Cover Install Chimney CoversFor Vented Installations MakeElectrical ConnectionInstallGreaseFilters Complete InstallationRange Hood USE Cleaning Range Hood CareWiring Diagram IntheU.S.A Assistance or ServiceAccessories List InCanadaWhirlpool Corporation Major Appliance Warranty CallSécurité DE LA Hotte D’ASPIRATION Votre sécurité et celle des autres est très importanteConservez CES Instructions Exigences demplacement OutillageetpiècesInstallations sans décharge à lextérieur recyclage Dimensions à respecter lors de linstallationInstallations pour régions à climat froid Exigencesconcernant lévacuationSpécificationsélectriques Installation des vis de montage de la hotte Instructions DinstallationPréparationdelemplacement Dépose des filtresInstallations avec décharge à lextérieur Installationde lahotteInstallation de la bride de support de la cheminée Installations sans décharge à lextérieur recyclageRaccordementélectrique Installation de la section supérieure du cache-cheminée Installationducache-cheminéeInstallation desfiltresà graisse Installation de la section inférieure du cache-cheminéeAchever linstallation Utilisation DE LA HotteEntretien DE LA Hotte NettoyageSchéma DE Câblage Assistance OU Service ListedaccessoiresGarantie DES Gros Appareils Ménagers Whirlpool Corporation W10029780

W10029780 specifications

The KitchenAid W10029780 is a versatile appliance part designed specifically for use with KitchenAid appliances, ensuring efficient performance and durability in the kitchen. This part is primarily known for its compatibility with a wide range of KitchenAid refrigerators, serving as a crucial element in maintaining the appliance's functionality.

One of the standout features of the KitchenAid W10029780 is its innovative design tailored to optimize cooling performance. By facilitating effective temperature control, this part helps maintain the ideal environment for food storage, contributing to the freshness and longevity of your perishables. The unit also benefits from robust construction materials that withstand the rigors of daily kitchen use, ensuring that it remains reliable for years.

In addition to its structural integrity, the W10029780 incorporates advanced technology aimed at minimizing energy consumption. This efficiency not only supports sustainable practices but also helps users save on energy costs. The part's design includes features that promote optimal airflow within the refrigerator, preventing cold spots and ensuring that all areas receive adequate cooling.

The ease of installation is another key characteristic of the KitchenAid W10029780. Homeowners and DIY enthusiasts can replace the part without the need for professional assistance, thanks to its straightforward design. Comprehensive installation instructions accompany the product, guiding users through the replacement process with clarity.

Furthermore, the KitchenAid W10029780 is also engineered for compatibility with various models of KitchenAid refrigerators, making it a versatile choice for those looking to maintain their kitchen appliances. The part's reliability has earned it positive reviews from customers who appreciate its seamless integration into their existing kitchen setups.

In conclusion, the KitchenAid W10029780 stands out as a vital component for those looking to enhance their refrigerator's efficiency and longevity. With its emphasis on cooling performance, energy efficiency, user-friendly installation, and compatibility with various models, this part exemplifies the brand's commitment to quality and customer satisfaction. Whether you are a seasoned chef or a casual home cook, the KitchenAid W10029780 is likely to meet your appliance maintenance needs effectively.