Installation Instructions

■Check with a qualified electrician if you are not sure range hood is properly grounded.

■Do not have a fuse in the neutral or ground circuit.

■The range hood must be connected with copper wire only.

■The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed copper cable.

■Wire sizes (copper wire only) and connections must conform with the rating of the appliance as specified on the model/ serial rating plate.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

■A ¹⁄₂" (12.7 mm) UL listed or CSA approved strain relief must be provided at each end of the power supply cable (at the range hood and at the junction box).

Venting Options

General venting installation

For vented installations:

Make necessary cuts in the wall for vent fittings.

NOTE: The hood exhaust may be directed out the rear of the hood by removing the motor assembly and rotating it so the exhaust collar is located on the rear of the hood. If this is desired, see “Change Hood to Rear Exhaust” section to change the exhaust direction.

IMPORTANT: Make sure the vent system is installed before installing range hood.

For recirculating installations:

A vent system and vent grill (not provided) that directs the recirculated air back into the room either through the soffit or through the cabinet top is required. Use Recirculation Kit Part Number 4396565. For ordering information, see “Assistance or Service.”

IMPORTANT: If venting through the cabinet top, do not terminate the exhaust into dead air space such as an attic or enclosed soffit.

When venting through the soffit, assemble the vent system (not provided) you will use over the exhaust collar, but do not attach the vent system yet.

NOTE: The vent system can exhaust out the front of the soffit or be rotated to exhaust out the side or end of the soffit.

Venting through the soffit

1.On a flat surface with a protective covering, assemble the vent system you will use (not provided) over the exhaust collar, but do not attach the vent system yet.

NOTE: The vent system can exhaust out the front of the soffit or be rotated to exhaust out the side or end of the soffit.

2.Measure distance “A” (from top of hood to centerline of 6" [15.2 cm] round vent). Mark the distance “A” on soffit.

3.Mark and cut a 6" (15.2 cm) round vent opening.

Venting through cabinet top

1.Mark the location where vent cover will be installed in the cabinet top and cut a 6" (15.2 cm) round vent opening for the vent cover.

IMPORTANT: Do not terminate exhaust into a dead air space such as an attic or enclosed soffit.

	B	C
	B
A		D
		E

	A. Vent system	D. Ceiling or soffit
	B. Vent cover	E. Hood
	C. Cabinet top

Prepare Location

■For vented installations, it is recommended that the vent system be installed before hood is installed.

■Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for vent fittings.

■Check that all the installation parts and the box with filters have been removed from the shipping carton.

Preparation

WARNING

Excessive Weight Hazard

Use two or more people to move and install range. Failure to do so can result in back or other injury.

1.If possible, disconnect power and/or gas supply and move freestanding or slide-in range from cabinet opening to provide easier access to rear wall.

2.Select a flat surface for assembling the hood. Cover that surface with a protective covering such as a blanket or cardboard during assembly.

Ventilation Hood specifications

The KitchenAid Ventilation Hood is a premium kitchen accessory designed to enhance your cooking experience while ensuring a clean and pleasant environment in your kitchen. This essential appliance combines aesthetics with functionality, making it not only a practical component of your culinary space but also an elegant fixture that complements your kitchen design.

One of the standout features of the KitchenAid Ventilation Hood is its powerful ventilation system. With a range of CFM (cubic feet per minute) options, these hoods effectively capture smoke, steam, and cooking odors, ensuring that your kitchen remains fresh during and after meal preparation. The three-speed blower allows you to choose the perfect level of air circulation based on the intensity of your cooking, providing flexibility to match your culinary needs.

In addition to its efficiency, the KitchenAid Ventilation Hood is designed with a sleek and modern aesthetic. The stainless steel finish not only gives it a professional appearance but also ensures durability and easy maintenance. The hood is available in various styles, including wall-mounted, under-cabinet, and island configurations, allowing you to select the perfect model that fits both your kitchen layout and personal taste.

Technological innovations enhance the user experience as well. Many KitchenAid Ventilation Hoods come equipped with LED lighting, which illuminates your cooking surface effectively, enhancing visibility. This energy-efficient lighting is designed to last longer than traditional bulbs, reducing the frequency of replacements while providing bright, even illumination.

Moreover, these hoods often feature dishwasher-safe filters, making cleanup straightforward. The filters are designed specifically to capture grease and other particulates, ensuring optimal performance and longevity of your appliance. Some models also incorporate charcoal filters, which assist in reducing odors even further, perfect for kitchens that frequently prepare aromatic dishes.

Noise levels are another concern with ventilation hoods, but KitchenAid addresses this with its Quiet-Efficient Ventilation Technology. This feature ensures that even at higher speeds, the hood operates more quietly, allowing for an enjoyable cooking environment without overwhelming noise.

In summary, the KitchenAid Ventilation Hood is a perfect blend of style, efficiency, and advanced technology. With its powerful ventilation capabilities, aesthetic appeal, user-friendly features, and quiet operation, it is an ideal addition to any kitchen, promising both functionality and elegance to enhance your culinary endeavors.