KitchenAid Ventilation Hood Location Requirements, Venting Requirements, Product dimensions

Page 4

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Installation clearances

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the rear wall.

Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult your cooktop/range manufacturer installation instructions before making any cutouts.

Grounded electrical outlet is required. See “Electrical Requirements” section.

The hood is factory set for vented installations. For recirculating installations, Recirculation Kit Part Number 4396565, including vent cover and 2 charcoal filters are available from your dealer.

All openings in ceiling and wall where range hood will be installed must be sealed.

30" (76.2 cm) or

36" (91.4 cm) min.

cabinet opening width

24" (61 cm) min. 30" (76.2 cm) suggested max. bottom of hood to cooking surface

18" (45.7 cm) min. clearance upper cabinet to countertop

70⁵⁄₁₆"

(178.6 cm)

min.

76⁵⁄₁₆"

(193.8 cm)

max.

to bottom of cabinet frame

Product dimensions

5⁷⁄₈" (14.9 cm) dia.

exhaust collar

36" (91.4 cm) countertop

height

Interchangeable

Front Trim

9¹⁵⁄₁₆"

(25.2 cm)

 

 

29¹⁵⁄₁₆" (76.0 cm) – 30" (76.2 cm) model

20³⁄₁₆"

 

(51.3 cm)

 

35¹⁵⁄₁₆" (91.3 cm) – 36" (91.4 cm) model

 

 

 

Vent and electrical openings and mounting screw locations

5⁷⁄₈"

centerline of

9¹⁄₈"

exhaust collar

(23.2 cm)

(14.9 cm)

 

 

 

dia.

 

 

1¹⁄₄"

 

1³⁄₁₆"

(3.2 cm)

 

(3.0 cm)

 

 

3¹⁵⁄₁₆"

 

 

(10.0 cm)

1⁵⁄₁₆"

(3.3 cm)

1⁵⁄₁₆"

centerline

(3.3 cm)

of hood

7¹⁄₂"

(19.0 cm)

electrical

knockouts

Venting Requirements

Use a straight run or as few elbows as possible.

Do not terminate the vent system in an attic or other enclosed area.

Do not use a 4" (10.2 cm) laundry-type wall caps.

Vent system must terminate to the outside.

Use only a 6" (15.2 cm) round metal vent. Rigid metal vent is recommended. Do not use plastic or metal foil vent.

The size of the vent should be uniform.

The vent system must have a damper. If roof or wall cap has a damper, do not use damper supplied with the range hood.

Use duct tape to seal all joints in the vent system.

Use caulking to seal exterior wall or roof opening around the cap.

Determine which venting method is best for your application.

4

Image 4
Contents Avec garniture de façade interchangeable 9763384 Rev. A1Range Hood Safety Table of ContentsInstallation Requirements Tools and PartsProduct dimensions Location RequirementsVenting Requirements Vent and electrical openings and mounting screw locationsElectrical Requirements Venting methodsCalculating Vent System Length Example vent systemVenting Options Installation InstructionsPrepare Location Cut a 1¹⁄₄ 3.2 cm hole for power supply cable Change Hood to Optional Rear ExhaustInstall Range Hood Make Electrical ConnectionCheck Operation Install FiltersInterchangeable Front Trim Range Hood Controls Range Hood LampsReplacing Hood Lamps Fuse Cleaning AccessoriesRequesting Assistance or Service U.S.ACanada Our consultants provide assistance withKitchenaid Ventilation Warranty ONE Year Limited WarrantyItems Kitchenaid will not PAY for Disclaimer of Implied Warranties Limitation of RemediesWiring Diagram Slide SwitchesSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteConservez CES Instructions Exigences Dinstallation Exigences demplacementDimensions du produit Outillage et piècesDégagements de séparation à respecter Exigences concernant lévacuationMéthodes dévacuation Calcul de la longueur effective du circuit dévacuation Spécifications électriquesLongueur maximum = 35 pi 10,7 m Instructions Dinstallation Préparation de l’emplacementInstructions générales Décharge à travers le soffiteMoteur du ventilateur Vis Installation de la hotte de cuisinière Raccordement électriqueInstallation des filtres Contrôle du fonctionnementGarniture Avant Interchangeable Pièce nCommandes de la hotte de cuisinière DE CuisinièreEntretien DE LA Hotte DE Cuisinière Lampes de la hotte de cuisinièreFiltres pour installation avec recyclage NettoyageSurfaces externes Filtres métalliquesAssistance OU Service AccessoiresGarantie Limitée DE UN AN GarantiedusystèmedeventilationkitchenaidKitchenaid NE Prendra PAS EN Charge Schéma DE Câblage 9763384 Rev. a
Related manuals
Manual 1 pages 33.27 Kb

Ventilation Hood specifications

The KitchenAid Ventilation Hood is a premium kitchen accessory designed to enhance your cooking experience while ensuring a clean and pleasant environment in your kitchen. This essential appliance combines aesthetics with functionality, making it not only a practical component of your culinary space but also an elegant fixture that complements your kitchen design.

One of the standout features of the KitchenAid Ventilation Hood is its powerful ventilation system. With a range of CFM (cubic feet per minute) options, these hoods effectively capture smoke, steam, and cooking odors, ensuring that your kitchen remains fresh during and after meal preparation. The three-speed blower allows you to choose the perfect level of air circulation based on the intensity of your cooking, providing flexibility to match your culinary needs.

In addition to its efficiency, the KitchenAid Ventilation Hood is designed with a sleek and modern aesthetic. The stainless steel finish not only gives it a professional appearance but also ensures durability and easy maintenance. The hood is available in various styles, including wall-mounted, under-cabinet, and island configurations, allowing you to select the perfect model that fits both your kitchen layout and personal taste.

Technological innovations enhance the user experience as well. Many KitchenAid Ventilation Hoods come equipped with LED lighting, which illuminates your cooking surface effectively, enhancing visibility. This energy-efficient lighting is designed to last longer than traditional bulbs, reducing the frequency of replacements while providing bright, even illumination.

Moreover, these hoods often feature dishwasher-safe filters, making cleanup straightforward. The filters are designed specifically to capture grease and other particulates, ensuring optimal performance and longevity of your appliance. Some models also incorporate charcoal filters, which assist in reducing odors even further, perfect for kitchens that frequently prepare aromatic dishes.

Noise levels are another concern with ventilation hoods, but KitchenAid addresses this with its Quiet-Efficient Ventilation Technology. This feature ensures that even at higher speeds, the hood operates more quietly, allowing for an enjoyable cooking environment without overwhelming noise.

In summary, the KitchenAid Ventilation Hood is a perfect blend of style, efficiency, and advanced technology. With its powerful ventilation capabilities, aesthetic appeal, user-friendly features, and quiet operation, it is an ideal addition to any kitchen, promising both functionality and elegance to enhance your culinary endeavors.