KitchenAid W10440541A Adjust Leveling Legs, Install Anti-Tip Bracket, Freestanding Ranges

Page 9

2.Measure from the floor to the underside of the range cooktop.

C

B

A

A. Distance from floor to underside of range cooktop

B. Range side frame

C.Cooktop

3.Your leveling height will be the difference between the 2 measurements you have just taken.

Freestanding Ranges:

1.Measure the distance of the countertop to the floor.

2.Then measure from the top of the range cooktop trim to the floor.

A

A. Distance from the top of the range cooktop trim to the floor

3.Your leveling height will be the difference between the 2 measurements you have just taken.

Adjust Leveling Legs

1.If range height adjustment is necessary, use a wrench or pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to a standing position.

NOTE: To place range back up into a standing position, put a sheet of cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto the cardboard or hardboard.

2.Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (5 mm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs.

3.When the range is at the correct height, check that there is adequate clearance under the range for the anti-tip bracket. Before sliding range into its final location, check that the anti- tip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation.

Install Anti-Tip Bracket

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

1.Remove the anti-tip bracket from where it is taped inside the storage drawer or warming drawer.

2.Determine which mounting method to use: floor or wall.

If you have a stone or masonry floor, you can use the wall mounting method. If you are installing the range in a mobile home, you must secure the range to the floor.

3.Determine and mark the centerline of the cutout space. The mounting can be installed on either the left side or right side of the cutout. Position the mounting bracket against the wall in the cutout so that the V-notch in the bracket is

13¹³⁄₆₄" (33.62 cm) from the centerline as shown.

B

Centerline

A

A. 13¹³⁄₆₄" (33.62 cm)

B. Bracket V-notch

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents W10440541A Table DES Matières Table of ContentsYour safety and the safety of others are very important Range SafetyInstallation Requirements Tools and PartsLocation Requirements Product Dimensions Freestanding Range Mobile Home Additional Installation RequirementsMobile home installations require Slide-in RangeCabinet Dimensions Electrical Requirements U.S.A. OnlyElectrical Connection If connecting to a 4-wire system If connecting to a 3-wire systemElectrical Requirements Canada Only Countertop Preparation Installation InstructionsUnpack Range Measure for Proper HeightAdjust Leveling Legs Install Anti-Tip BracketFreestanding Ranges Direct Wire Power Supply CordElectrical Connection U.S.A. Only Floor MountingStyle 2 Direct wire strain relief Style 1 Power supply cord strain reliefWire connection Power Supply Cord Wire Connection Direct Wire Direct Wire Installation Copper or Aluminum WireWire Awg Torque Bare Wire Torque SpecificationsVerify Anti-Tip Bracket Is Installed Engaged On models with a storage drawerOn models with a warming drawer For power supply cord-connected ranges Complete InstallationLevel Range Moving the RangeFor direct-wired ranges Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreExigences Dinstallation Exigences demplacementOutillage et pièces Cuisinière coulissante Dimensions du produit Cuisinière autoportanteCuisinière coulissante Dimensions du placardPréparation du plan de travail Spécifications électriquesDéballage de la cuisinière Instructions DinstallationMesures pour une hauteur appropriée Cuisinières autoportantesAjuster les pieds de nivellement Installation de la bride antibasculementMontage au plancher Montage muralRéglage de laplomb de la cuisinière Sur les modèles avec tiroir de remisageSur les modèles avec tiroir-réchaud Déplacement de la cuisinière Achever l’installationCuisinières alimentées par cordon d’alimentation Si la cuisinière ne fonctionne pas, contrôler ce qui suitPour les cuisinières avec câblage direct 11/11
Top Page Image Contents