KitchenAid Series KHWG160 installation instructions Installing the Tank, Cm below the first line

Page 5

Installing the Tank

1.Position tank vertically beneath faucet so that the longer copper tube from the faucet reaches the easy-connect fitting on top of the tank.

2.Use a pencil to mark on the wall where the top of tank needs to be located. Set tank aside. Mark a second line 2-1/4"

(5.7 cm) below the first line.

IMPORTANT: The tank must be positioned so that the copper tubing and flexible tubing from the faucet does not kink.

3.Position mounting bracket on wall so that bottom of mounting bracket is even with the lower line.

4.Use two screws (and plastic anchors if attaching to dry wall) to fasten mounting bracket to wall. Hang tank on bracket.

2-1/4"

(5.7 cm)

off position

mounting

bracket

6.Connect the flexible tube from the faucet to the center tank tube. Make sure the flexible tube does not kink. To avoid kinking, the tube may be shortened.

The center tank tube is not an easy-connect fitting. To connect the flexible tube, use pliers and open the supplied hose clamp. Slide the clamp onto the flexible tube about 2" (5 cm) from the tube end.

flexible tube

hose clamp

tank tube

7.Push the flexible tube down onto the tank tube as far as it will go. Position the hose clamp so that it is close to the end of flexible tube.

hose clamp

IMPORTANT: Do not plug power supply cord into outlet at this time.

5.IMPORTANT: Do not lengthen, twist or tightly bend tubing. Do not use any sealing compounds.

Connect the longest 1/4" copper faucet tube to the rear easy- connect fitting on top of tank. Push tubing straight into fitting as far as it will go. Pull on tubing. The tubing should not come out when properly installed.

copper

 

faucet tube

collet

 

easy-connect fitting

NOTE: If you need to remove tubing, push down on collet. Pull tubing out of easy-connect fitting. It is easier to push the collet down if a 1/4" or 7 mm open-end wrench is used as shown.

copper

1/4" or 7 mm

faucet tube

open-end

 

wrench

collet

 

8.Install saddle valve kit or other plumbing parts as needed to connect 1/4" tubing from faucet easy-connect fitting to cold water supply line.

9.Flush line into bucket or pan to remove any debris that may have been trapped in supply line during plumbing connection.

10.Check that water flows freely and that there are no leaks.

11.Connect 1/4" water supply line tubing to faucet copper tubing with the factory-assembled easy-connect fitting. Push water supply line tubing straight into fitting as far as it will go. Pull on tubing. The tubing should not come out when properly installed.

factory assembled easy-connect fitting

NOTE: If you need to remove tubing, push down on collet and pull tubing out of easy-connect fitting.

IMPORTANT: For proper operation, do not remove the factory-assembled easy-connect fitting from tube.

12.Open water line to faucet.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 85788981 Model SeriesRecord your model’s information HOT Water Dispenser Safety Table of ContentsLocation Requirements Installation RequirementsTools and Parts Installing the Faucet Installation InstructionsElectrical Requirements Water Supply RequirementsCm below the first line Installing the TankTemperature control Complete InstallationBefore first use Dispensing hot waterFor short periods 2-30 days of nonuse Cleaning the Faucet ScreenEnergy-saving tips and preparation for periods of nonuse Troubleshooting Guide Before Calling for ServiceIf you need assistance or service in Canada Requesting Assistance or ServiceIf you need assistance or service in U.S.A 8578898 INSTANT-HOTwater dispenser WarrantyEnregistrement des renseignements concernant votre modèle Modèle sérieDemande D’ASSISTANCE OU DE Service Instructions D’INSTALLATIONTable DES Matières Sécurité DU Distributeur D’EAU ChaudeOutillage et pièces Exigences D’INSTALLATIONEmplacement d’installation Installation du robinet de puisage Instructions D’INSTALLATIONMéthode recommandée de mise à la terre Spécifications électriquesInstallation du chauffe-eau Utilisation DU Achever l’installationAvant la première utilisation Réglage de la températurePour une brève période d’inutilisation 2 à 30 jours ’EAU ChaudeNettoyage du tamis de filtration du robinet Guide de dépannage Avant de demander l’intervention d’un technicienSi vous avez besoin d’assistance ou de service au Canada Demande D’ASSISTANCE OU DE ServiceSi vous avez besoin d’assistance ou de service aux É.-U Kitchenaid NE Prendra PAS EN Charge Garantie du distributeur d’eau INSTANT-HOT

Series KHWG160 specifications

The KitchenAid Series KHWG160 is an impressive addition to the KitchenAid lineup, designed specifically for the modern cooking enthusiast who values both functionality and style. This versatile kitchen appliance is primarily a high-performance hand mixer that caters to a variety of culinary needs.

One of the standout features of the KHWG160 is its powerful 160-watt motor. This robust motor allows users to tackle a wide range of tasks, from whipping cream to mixing dough, with ease. Its variable speed settings—10 in total—enable precise control over mixing speeds, ensuring that users can achieve the perfect consistency for any recipe. The slower first speed is particularly useful for incorporating dry ingredients without creating a mess.

The KHWG160 is equipped with a variety of attachments, making it an essential tool in any kitchen. The included stainless steel beaters are not only durable but also designed for effective mixing. For those looking to fold ingredients gently, the included dough hooks and whisk attachment provide additional versatility, allowing the user to tackle tasks such as kneading bread dough or aerating batter.

In terms of design, the KHWG160 showcases KitchenAid's signature aesthetic, featuring a sleek and elegant profile available in multiple colors. This attention to stylistic detail ensures that the hand mixer is not only a functional tool but also a beautiful addition to your kitchen countertop.

Another notable technology featured in the KHWG160 is the soft-start function. This thoughtful design prevents splattering and ensures that ingredients are blended smoothly from the very start of the mixing process. Users appreciate this feature, as it enhances the overall cooking experience and results in cleaner work surfaces.

The KHWG160 also features a convenient eject button located on the top of the mixer. This allows for easy removal of attachments, streamlining the cleanup process and enhancing user convenience.

Overall, the KitchenAid Series KHWG160 stands out for its combination of power, versatility, and aesthetic appeal. It's an excellent choice for anyone looking to elevate their cooking experience, making it a valuable investment in both everyday cooking and special occasion baking. Whether you're a beginner or a seasoned home chef, this hand mixer is designed to make every culinary task enjoyable and efficient.
Top Page Image Contents