KitchenAid W10206425A manual Condenser, Interior Components, Dirty or clogged condenser

Page 10

7.Press the CLEAN button. See “Using the Controls.” The light will blink, indicating that the cleaning cycle is in process. When the indicator light turns green (approximately

70 minutes), the cleaning cycle is complete. During the cleaning cycle, the system will both clean and rinse itself.

8.After the cleaning cycle is complete, remove the drain cap from the water pan. Look for any cleaning solution left in the water pan. If cleaning solution drains from the water pan, you should run the clean cycle again. Be sure to replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan and you will have either thin ice or no ice.

NOTE: Severe scale buildup may require repeated cleaning with a fresh quantity of cleaning solution.

9.Push the selector switch to ON to resume ice production.

Condenser

A dirty or clogged condenser:

■Obstructs proper airflow.

■Reduces ice making capacity.

■Causes higher than recommended operating temperatures which may lead to component failure.

WARNING

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug ice maker or disconnect power.

2.Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support.

3.Pull the bottom forward and then pull down to remove the lower access panel.

A

A

B

B

A. Lower access panel screws

B. Base grille screws

4.Remove dirt and lint from the condenser fins and the unit compartment with a brush attachment on a vacuum cleaner.

5.Replace the lower access panel using the four screws.

6.Plug in ice maker or reconnect power.

Interior Components

1.Unplug ice maker or disconnect power.

2.Open the storage bin door and remove any ice that is in the bin.

3.Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

4.Remove the two screws that hold the cutter grid cover in place and remove the cutter grid cover.

5.Unplug the wiring harness from the left side of the cutter grid.

A

B

A. Cutter grid cover

B.Screws

6.Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7.Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

D

A

 

B

E

C

F

 

A. Cutter grid harness

D. Ice level sensor harness

B. Screw

E. Plastic spacer

C. Cutter grid

F. Screw

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents ICE Maker Table of Contents Table DES MatièresICE Maker Safety Your safety and the safety of others are very importantUnpack the Ice Maker Installation InstructionsCleaning Before Use Location RequirementsLeveling Electrical RequirementsWater Supply Requirements Recommended grounding methodConnect Water Supply Connecting the Water LineRear View Gravity Drain System Connecting the DrainDrain Connection Drain Pump System on some modelsHow Your Ice Maker Works ICE Maker USENormal Sounds Ice Making ProcessCleaning Using the ControlsICE Maker Care Interior Components CondenserDirty or clogged condenser Vacation and Moving Care For ice makers with a drain pump installedTo shut down the ice maker Ice Maker Operation TroubleshootingIce Production Plumbing Problems Ice QualityU.S.A Assistance or ServiceIf you need replacement parts CanadaItems Excluded from Warranty Kitchenaid ICE Maker WarrantyLimited Warranty This limited warranty does not coverPage Sécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importanteDéballage de la machine à glaçons Instructions D’INSTALLATIONEmplacement d’installation Enlèvement des matériaux d’emballageSpécifications de l’alimentation en eau Méthode de mise à la terre recommandéeSpécifications électriques NivellementRaccordement à la canalisation d’eau Raccordement du tuyau d’eauVUE Arrière Raccordement au conduit dévacuationSystème de vidange par gravité VUE LatéraleSystème à pompe de vidange sur certains modèles Sons normauxRaccordement du conduit dévacuation Utilisation DE LA Machine À Glaçons Utilisation des commandesHoliday Mode mode vacances Fonctionnement de la machine à glaçonsEntretien DE LA Machine À Glaçons NettoyageComposants intérieurs CondenseurUn condenseur sale ou obstrué Précautions à prendre pour les vacances Ou le déménagement Arrêt de la machine à glaçonsLa machine à glaçons semble bruyante DépannageLa machine à glaçons ne fonctionne pas Machine à glaçons avec pompe de vidangeQualité des glaçons Production de glaçonsProblèmes de plomberie Pour plus d’assistance Assistance OU ServiceSi vous avez besoin de pièces de rechange Nos consultants fournissent l’assistance pourÉléments Exclus DE LA Garantie Garantie DE LA Machine À Glaçons KitchenaidGarantie Limitée La présente garantie limitée ne couvre pasPage W10206425A All rights reserved

W10206425A specifications

The KitchenAid W10206425A is a versatile and essential component in many kitchens, known for its functionality and advanced features. This refrigerator water filter is designed specifically for various KitchenAid refrigerator models, ensuring that you have access to clean, great-tasting drinking water and ice.

One of the main features of the W10206425A filter is its advanced filtration technology. This filter effectively reduces impurities and contaminants from your water, including chlorine taste and odor, lead, mercury, and various other harmful substances. This not only enhances the quality of your drinking water but also contributes to the safety and overall health of your family.

A distinctive characteristic of the W10206425A is its easy installation process. Designed with user convenience in mind, this filter can be replaced without requiring any special tools or complicated procedures. This means that homeowners can easily swap out old filters for new ones, promoting regular maintenance of their refrigerator's water system. Additionally, it is recommended to replace the filter approximately every six months to ensure continued high performance and efficient filtration.

The filter is also designed to improve the efficiency of the refrigerator's ice maker, providing consistently clear and fresh-tasting ice. This is particularly beneficial for those who frequently use ice in beverages, ensuring that the ice does not alter the taste of drinks through contamination.

In terms of compatibility, the W10206425A filter works with various KitchenAid refrigerator models, making it a reliable choice for many households. It is essential to check your refrigerator model to ensure compatibility before purchasing to avoid any issues during installation.

Moreover, KitchenAid is known for its commitment to quality and longevity. The W10206425A filter is constructed from durable materials designed to last through numerous filtering cycles while maintaining optimal performance.

In summary, the KitchenAid W10206425A water filter is a crucial accessory for any KitchenAid refrigerator, designed to provide superior filtration, ease of use, and compatibility with various models. Its features ensure that your water and ice remain pure and refreshing, making it a wise investment for your kitchen needs. Whether for daily hydration or entertaining, this filter enhances your overall kitchen experience.
Top Page Image Contents