Installation Instructions

Unpack the Ice Maker

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

■To remove any remaining tape or glue from the exterior of the ice maker, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. Do not use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your ice maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the “Ice Maker Care” section.

Location Requirements

■To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

■Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve and either a gravity-drain system or condensate pump to carry the water to an existing drain.

■Choose a well ventilated area with temperatures above 55°F (13°C) and below 100°F (38°C). Best results are obtained between 70°F (21°C) and 90°F (32°C).

■This ice maker must be installed in an area sheltered from the elements, such as wind, rain, water spray or drips.

■When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as shown.

NOTES:

■Be sure the power supply cord is not pinched between the ice maker and the cabinet.

■Be sure the water supply line is not pinched between the ice maker and the cabinet.

■Be sure the drain line (on some models) is not pinched between the ice maker and the cabinet.

34"

(86.4 cm)

Min.

34¹⁄₂"

(87.6 cm)

Max.

14¹⁄₂" (36.8 cm)

3¹⁄₂" 9"

(8.9 cm)(22.9 cm)

28¹⁄₂"

(72.4 cm)

24"

(60.1 cm)

18"

(45.7 cm)

A. Recommended location for electrical and plumbing fixtures

B. Floor level

■Choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See the “Leveling” section.

W10206425A specifications

The KitchenAid W10206425A is a versatile and essential component in many kitchens, known for its functionality and advanced features. This refrigerator water filter is designed specifically for various KitchenAid refrigerator models, ensuring that you have access to clean, great-tasting drinking water and ice.

One of the main features of the W10206425A filter is its advanced filtration technology. This filter effectively reduces impurities and contaminants from your water, including chlorine taste and odor, lead, mercury, and various other harmful substances. This not only enhances the quality of your drinking water but also contributes to the safety and overall health of your family.

A distinctive characteristic of the W10206425A is its easy installation process. Designed with user convenience in mind, this filter can be replaced without requiring any special tools or complicated procedures. This means that homeowners can easily swap out old filters for new ones, promoting regular maintenance of their refrigerator's water system. Additionally, it is recommended to replace the filter approximately every six months to ensure continued high performance and efficient filtration.

The filter is also designed to improve the efficiency of the refrigerator's ice maker, providing consistently clear and fresh-tasting ice. This is particularly beneficial for those who frequently use ice in beverages, ensuring that the ice does not alter the taste of drinks through contamination.

In terms of compatibility, the W10206425A filter works with various KitchenAid refrigerator models, making it a reliable choice for many households. It is essential to check your refrigerator model to ensure compatibility before purchasing to avoid any issues during installation.

Moreover, KitchenAid is known for its commitment to quality and longevity. The W10206425A filter is constructed from durable materials designed to last through numerous filtering cycles while maintaining optimal performance.

In summary, the KitchenAid W10206425A water filter is a crucial accessory for any KitchenAid refrigerator, designed to provide superior filtration, ease of use, and compatibility with various models. Its features ensure that your water and ice remain pure and refreshing, making it a wise investment for your kitchen needs. Whether for daily hydration or entertaining, this filter enhances your overall kitchen experience.